Adjusting Edit Timing - Sony DSR-45 Service Manual

DSR-45/45P
Control signal connections
The following shows an example of the control signal
connections needed to enable the editing controller to
control all other A/B roll editing system devices.
Editing controller
PLAYER 1 9-pin remote control cable
MIXER
PLAYER 2 9-pin remote control cable
RECORDER 9-pin remote control cable
SWITCHER
EDITOR
Audio mixer Switcher
To control the unit from an editing controller, set the
REMOTE/LOCAL switch of this unit to REMOTE.
Furthermore, if you use an RS-422A connection, set the
remote selector of this unit to RS-422A.
a) Use an optional 9-pin remote control cable.
Connection of a video monitor
Set up the following connections to enable monitoring
of video and audio signals on a video monitor. In
addition to video signals, you can check time data, the
DSR-45/45P's operation mode, alarm messages, and
other information displayed as text on the monitor
screen.
Video monitor
75 Ω termination switch: ON
(or attach a 75 Ω terminator)
Input switches: Set
according to the type of input
signals.
Video input
Phono jack cable (not supplied)
Note
When you want to monitor the edited tape, use the
monitor output connector on the recording VCR.
DSR-45/45P (Player 1)
a)
RS-422A
a)
a)
REMOTE REMOTE
Player 2
Recorder
Chapter 3 Using the Unit as a Player in an Editing System
DSR-45/45P
Audio input
MONITOR MONITOR
AUDIO VIDEO
Chapter 3 Using the Unit as a Player in an Editing System
Connections for an A/B Roll Editing System
Video/audio signal connections
The following shows an example of video/audio signal
connections in an A/B roll editing system. In this
example, analog component signals are used as the
video signals and XLR 3-pin connectors are used as
audio output connectors.
COMPONENT VIDEO IN
(Y, R–Y, B–Y)
Recorder
AUDIO IN
CH-1
3
CH-1 OUT
Delay unit
CH-1 IN
3
LINE OUT LINE OUT
Audio mixer
1 12-pin y 3×BNC cable
(not supplied) (Consult
your Sony dealer about
this cable.)
2 12-pin dubbing cable
(not supplied)
3 Cable with XLR
connectors (not supplied)
54
53
(GB) Chapter 3 Using the Unit as a Player in an Editing System
(GB)

Adjusting Edit Timing

For details, refer to the instruction manuals of the editing
controller you use.
Using this unit as a player with the RM-
450/450CE
1
Set the SYNCHRO selector to ON.
2
Set item number 3 of the SYSTEM PRESET right
switch to OFF (it is set to OFF at factory).
Setting this to OFF adjusts the synchronization of
the recorder.
3
Execute the LEARN function.
Using this unit as player 1 with the PVE-
500
When using this unit as player 2, the relevant menu
item is indicated in ( ).
1
Set Sync Edt of SEtUP-10 to OFF in the SETUP
menu.
2
Set P1 dELAY (P2 dELAY) of SEtUP-13 (SEtUP-
14) to LEArn in the SETUP menu.
3
Set rEC Sync of SEtUP-15 to On in the SETUP
menu.
4
Set P1 Sync (P2 Sync) of SEtUP-16 (SEtUP-17) to
OFF in the SETUP menu.
5
Execute the LEARN function.
55 56
(GB) (GB) Chapter 3 Using the Unit as a Player in an Editing System
1-12
Switcher
PGM OUT
COMPONENT OUT
CH-2
3
CH-2 OUT
COMPONENT OUT
DSR-45/45P
Y, R-Y, B-Y OUT
(Player 1)
CH-2 IN
3
6 5 4 3 2 1 AUDIO OUT CH-1
3
3 CH-2
3 CH-3
3 CH-4
3
3
Player 2
For details of the video/audio input, connecting cables, and
audio mode settings, refer to the instruction manuals for the
devices used.
Using this unit as a player 1 with the FXE-
120/120P
• When using this unit as player 2, the relevant menu
item is indicated in ( ).
• When using an FXE-100/100P that has been
upgraded with an FXE-KIT1, the relevant menu item
is indicated in [ ].
1
Display item 104 [301] SYNC GRADE in the
SETUP menu, and set PLAYER1 (PLAYER2) to
PREROLL & PLAY.
2
Display item 301 (302) [401 as player 1, 402 as
player 2] DEVICE TYPE PLAYER1 (DEVICE
TYPE PLAYER2) in the SETUP menu, and set the
VCR device constants.
For details on device constants, see page 47 (GB).
3
Execute the LEARN function.
If the edit timing is out of adjustment, follow the
instruction given in "Adjusting the IN point"
below.
Adjusting the IN point
If the actual edited point does not accurately coincide
with the preset editing point, perform a fine adjustment
of the edit timing using the SETUP menu of the editing
controller. This improves the editing accuracy.
1
Display item 301 (302) [401 as player 1, 402 as
player 2] DEVICE TYPE PLAYER1 (DEVICE
TYPE PLAYER2) in the SETUP menu, and
change it from DISABLE to ENABLE.
2
Repeat the editing process several times and check
the shift of the editing point; that is, count the
number of frames to be adjusted.
Note
The editing results may differ between the
DISABLE and ENABLE settings of SETUP menu
item 301 (302) [401 as player 1, 402 as player 2].
Be sure to check the editing results after changing
the setting to ENABLE.
VIDEO INPUT
COMPONENT INPUT
VIDEO INPUT
COMPONENT INPUT
1
2
COMPONENT
OUTPUT
AUDIO OUTPUT
CH-1 CH-2