Connections For A Cut Editing System; Connections For An A/B Roll Editing System - Sony DSR-45 Service Manual

Connections for a Cut Editing System

The following figure shows a cut editing system
configuration that uses this unit as the player.
For details of connecting devices other than the DSR-45/
45P, refer to the instruction manual of each device.
S VIDEO OUT 5
VIDEO OUT 1
COMPONENT OUT
1
DSR-45/45P (player)
MONITOR VIDEO
3
MONITOR
AUDIO
3
VIDEO IN
AUDIO OUT CH-4
REF.IN
AUDIO OUT CH-3
AUDIO OUT CH-2
1
AUDIO OUT CH-1
2
RS-422A
REF.VIDEO
OUT
REF.VIDEO
Reference
OUT
video signal
generator
REF.VIDEO OUT
1
PLAYER REF.VIDEO IN
RECORDER
Editing controller
1 75 Ω coaxial cable (not supplied)
2 9-pin remote control cable (not supplied)
Connect one of the following as a video cable: 3 Phono jack cable (not supplied)
video cable (3BNC y 3BNC), S-video cable, or
75 Ω coaxial cable.
4 Cable with XLR connectors (not supplied)
Note
5 S-video cable (not supplied)
Use a recorder equipped with a synchronization
function.

Connections for an A/B Roll Editing System

The following is an example of a configuration of an
A/B roll editing system using the DSR-45/45P and a
recorder.
The purpose of the following figure is to clearly
DSR-45/45P (Player 1)
1
CH-1
Switcher
CH-2
CH- CH-
1/2 3/4
CH-3
MIN MAX
CH-4
Editing controller
Player 2 Audio mixer
Video signal
Audio signal
Reference video signal
Control signal
Note
Use a recorder equipped with a synchronization
function.
Note
The preroll time of the setting on the editing controller
is required to be more than five seconds.
S VIDEO IN
VIDEO IN
Y, R-Y, B-Y IN
Video
input
Source video
Audio
monitor
input
AUDIO IN CH-4
4
4 AUDIO IN CH-3
AUDIO IN CH-2
4
AUDIO IN CH-1
4
Recorder
REF.VIDEO
IN
1
MONITOR MONITOR REMOTE
AUDIO VIDEO OUT
3 1
Audio input Video input
Main video
monitor
2
49
Chapter 3 Using the Unit as a Player in an Editing System
indicate the flow of signals among the component
devices in this system. The specific connections and
the recorder settings for this system are described on
the following pages.
Reference video
signal generator
Main video
monitor
Source video
Recorder
monitor
Audio monitor
system
a)
Delay unit
a) When using a switcher, the phase of the video signals
processed by the switcher is delayed, which means that a
delay unit must be connected between the audio mixer's
output and the recorder's audio input.
51
Chapter 3 Using the Unit as a Player in an Editing System
Connections for a Cut Editing System
Settings on the Editing Control Unit
For details on the settings of the Editing Control Unit,
refer to "Adjusting Edit Timing" on page 56 (GB).
Settings on the DSR-45/45P (player) and a
recorder
Switch DSR-45/45P
REMOTE/LOCAL REMOTE
REMOTE RS-422A
For details, refer to the instruction manual of the recorder.
About reference video signals
• In order to provide stable video and audio signals for
analog editing, it is necessary for the built-in time
base corrector (TBC) to operate correctly. To ensure
this, input a reference video signal synchronized with
the video signal to the VIDEO IN REF.IN connector.
• Set EXT SYNC on the VIDEO SET menu to ON.
50
(GB) Chapter 3 Using the Unit as a Player in an Editing System
(GB)
Connections for an A/B Roll Editing System
Reference video signal connection
When you perform editing, be sure to use a reference
video signal.
For details on reference video signals, see "About reference
video signals" on page 50 (GB).
Editing controller
REF.
REF. VIDEO IN 75 Ω
VIDEO
termination switch: ON
IN
REF. VIDEO IN 75 Ω
termination switch: ON
Player 2
Use 75 Ω coaxial cables for all of these connections.
52
(GB) (GB) Chapter 3 Using the Unit as a Player in an Editing System
1-11
DSR-45/45P
Recorder
REMOTE
If you intend to make this unit perform playback
synchronized with an external reference video signal,
set EXT SYNC on the VIDEO SET menu to ON.
REF. VIDEO IN 75 Ω
termination switch: ON
REF. VIDEO IN
Switcher Recorder
4 3 2 1
BLACK BURST OUT
VIDEO IN REF.IN
DSR-45/45P (Player 1)
REF. VIDEO IN