Auto Pan Setup - JVC LWT0254-001B-H Instructions Manual

38 Setting Up the Camera Using RM-P2580 (continued)
EN

AUTO PAN Setup

Gradual Rotation
MENU button
SET button
CAMERA button
REMOTE CONTROL UNIT
CAMERA POSITION
SETUP
POWER
ALARM
MENU SET
KEY LOCK
LENS CAMERA/POSITION
1 2 3
CAMERA POSI-
SPEED
TION
4 5 6
CLOSE IRIS OPEN OPTION OPTION
1 2
FOCUS
7 8 9
NEAR FAR AUTO AUTO
AF
PAN PATROL
0
ZOOM
WIDE TELE CLEAR ENTER
/HOME
Numeric ENTER
keys button
ZOOM button
FOCUS button
AUTO PAN / PATROL / TRACE
AUTO PAN SET..
AUTO PATROL SET..
AUTO TRACE SET..
AUTO PAN / TRACE VIDEO ..
RM . A . PAN KEY
RM . A . PATROL KEY
< > < >
MENU RETURN SET SUB MENU
AUTO PAN/PATROL/TRACE screen
AUTO PAN SET
AUTO PAN MODE RETURN
AUTO PAN SPEED NORMAL
A . PAN POS . SET..
< >
MENU RETURN
AUTO PAN SET screen
AUTO PAN POSITION SET
[START] POS.SET →
< >
SET INVALID
DURING PAN MOVEMENT
< > < >
MENU RETURN SET L / R
AUTO PAN POSITION SET screen
This section describes procedures for setting the Auto Pan
function, which enables gradual horizontal rotation of the
camera. There are 3 Auto Pan modes, namely movement
between 2 points, rightward rotation and leftward rotation.
Select camera. (ARM-P2580 INSTRUCTIONS )
CAMERA buttonNNumeric key (Camera Number)NENTER button
●Video images of the selected camera will be output.
Display the MENU screen. (A pg. 21, steps
MENU button (3 sec.) N Select CAMERA.. using the PAN lever NSET
button.
●The MENU screen will be displayed.
PAN lever
Move the PAN lever upward/downward to shift the cursor (E)
to the AUTO PAN/PATROL/TRACE.. item, followed by
pressing the SET button.
RM-P2580
●The AUTO PAN/PATROL/TRACE screen will be displayed.
AUTO F-1 F-2 F-3
Press the SET button.
●Check that the cursor is at the AUTO PAN SET.. item and press SET
PAN/TILT
button.
Set the AUTO PAN MODE and AUTO PAN SPEED.
●Set the type of Auto Pan movement using the AUTO PAN MODE item.
RETURN (Movement between 2 points), RIGHT and LEFT
●Set the rotating speed of Auto Pan using the AUTO PAN SPEED item.
LOW, NORMAL, HIGH
AUTO PAN
Shift the cursor (E) to the A. PAN POS. SET.. item, and
button
press the SET button (only when in the Return mode).
●The AUTO PAN POSITION SET screen will be displayed.
Adjust the angle of view at the start position (only when in
the RETURN mode).
●Use the PAN lever, FOCUS button and ZOOM button for adjustment.
●Tilting operations or lens operations such as focusing and zooming are
not possible at the return position.
●During setting, a message indicating [START] POS.SET N will be
displayed at the bottom left of the screen.
Press the SET button (only when in the RETURN mode).
A . PAN
This switches the start position to the end position.
A . PATROL
Set the end position (only when in the RETURN mode).
●Set the return position using the PAN lever.
●During setting, a message indicating O [END] POS.SET will be
displayed at the bottom right of the screen.
Press the MENU button.
The Auto Pan position that has been set will be stored and the screen
will return to the previous menu ( AUTO PAN SET screen).
● Vertical movement (tilting) and lens operations are not possible at the return
position.
● Writing of preset data may fail if the SET button or MENU button is pressed when
the camera is moving. Ensure that the camera has come to a stop before pressing
the SET button and MENU button.
● The Manual Pan Limit mode will be temporarily turned OFF when this menu is
displayed. Manual Pan Limit can be set upon exiting this menu without affecting the
Auto Pan operation.
To enable Auto Pan operation upon setting, press the AUTO PAN button
on RM-P2580.
A RM-P2580 "Auto Pan operation", INSTRUCTIONS
to )