Setting & Displaying The Date & Time - Stryker 240-020-505 Instructions Manual

Preparation
Setting & Displaying the Date & Time
Use the following procedure to set the internal clock's date and time. Even when the DVD recorder's power is turned off, the clock's
date and time settings are stored using the internal battery.
Note that these settings are used to write the current date and time to a disc being recorded.
The DISPLAY screen can be used to indicate whether or not the date and time are to be displayed on-screen.
OPERATE
AUDIO
TITLE
CH1
DOLBY DIGITAL
LPCM MPEG
CH2
PHONES REV STOP
Setup Menu
DISC
INPUT SELECT
Setting the Date and Time
SYSTEM
DVD MENU
RECORDER
REMOTE
Setting of the date and time is carried out using the CLOCK ADJUST MENU
DISPLAY
screen. During this procedure, the monitor connected to the VIDEO LINE OUT
CLOCK ADJUST
NETWORK or Y/C OUT terminal is used to monitor the setting of data.
EXIT
Turn on the power and ensure that the DVD recorder is stopped.
1.
Press the SET UP button to display the Setup Menu.
CLOCK ADJUST MENU screen
2.
Open the CLOCK ADJUST MENU screen.
CLOCK ADJUST MENU
MENU
04/05/04
DATE
10:00
TIME
3.
Set the date and time as required.
DATE SETTING
04 / 05 / 04
4 5 04 SET
MONTH DAY YEAR
4.
After completing all of the required settings, return to the Setup
CLOCK ADJUST MENU
MENU Menu.
DATE 04/05/04
To do this, use the 6 or 7 buttons to select MENU and then press the SET
TIME 12:00
button.
5.
Return to the normal screen display.
To do this, press the SET UP button
or
Select EXIT from the Setup Menu and press the SET button.
CLOCK SETTING
07 : 44
07 44 SET
24
BUSY
OPEN/CLOSE
6 button
OPTION DV Y/C LINE
SET UP
CHAPTER
SET UP button
t button
SET
PLAY FWD PAUSE REC TOP
MENU MENU
SET button
8 button 7 button
Use the 6 and 7 buttons to select CLOCK ADJUST. (The currently
selected menu item is displayed as highlighted.)
Press the SET button to open the CLOCK ADJUST MENU screen.
Use the 6 and 7 buttons to select either DATE or TIME. Then press the
SET button.
Use the t and 8 buttons to select the digit to be changed. (The currently
selected digit is displayed as highlighted text.)
Use the 6 and 7 buttons to change the value of the selected digit.
Repeat steps through to make all of the required settings, and then
press the SET button.
Note
It is not possible to set the time in units of seconds. After setting the
minutes, press the SET button in sync with a time signal.
Setting & Displaying the Date & Time (continued)
Displaying the Date and Time
Use the DISPLAY MENU screen to indicate whether or not the date and time are
DISPLAY MENU screen
to be displayed on-screen and to set a display style. (
regarding setting methods.)
DISPLAY MENU
MENU DISPLAY MENU Screen Makeup
DISPLAY
ON
DISPLAY: This parameter is used to indicate whether or not data is to
TITLE/CHAPTER/INDEX
TITLE+CHAPTER
RECORDER MODE ON
TIME/DATE TIME+DATE
ON : Data will be displayed on-screen. The following parameters can be
REMAIN ON
DATE STYLE MM/DD/YY
OFF : No data is displayed on-screen.
TITLE+CHAPTER
LCD
TIME/DATE: This parameter is used to set the way in which the date
OFF
TIME
DATE
TIME + DATE : Both date or time are displayed.
DATE STYLE: This parameter is used to select the way in which the
YY/MM/DD : Year, month, day
MM/DD/YY : Month, day, year
DD/MM/YY : Day, month, year
To display date and time information on-screen;
On-screen display Only the date and time information from the VIDEO LINE OUT and Y/C OUT
terminal are displayed on screen.
000 min
Set DISPLAY to ON.
Set TIME/DATE to anything other than OFF.
Date and time information is displayed as follows.
Mode
Recording or Stop The value of the internal clock
REC Playback
04/05/06 TITLE 01 00:11:22
11:20:00 CHAPTER 01 00:11:22
TIME/DATE
Page 72 for details
be displayed on-screen.
used to indicate which data is to be displayed.
and time are displayed.
: Neither date or time are displayed.
: Only the time is displayed.
: Only the date is displayed.
date is to be displayed.
Displayed information
The date and time at which the current disc was
recorded.
25