Programming User Codes - DSC PowerSeries PC1616 Installation Manual

[,][2] Trouble Display
Refer to Appendix D – Troubleshooting Guide, for troubleshooting assistance and a detailed description of all trouble conditions.
When powering up the system for the first time, or in the event of a loss of power (including battery removal), a Loss of Clock trouble will
appear on the display. Press [8] on any keypad or [
[,][3] Alarm Memory Display
The Memory light will be ON if an alarm occurred during the last armed period. Press [,][3]. The Memory light will flash and the keypad
will display the zones that went into alarm.
To clear the Memory light, arm then disarm the system.
[,][4] Door Chime Enable/Disable
Press [,][4]. The keypad will emit 3 rapid beeps if the door chime feature is now enabled and a steady 2-second tone if it is now disabled.
The same function can be performed by pressing and holding the Chime function button for 2 seconds.
[,][5] Program User Codes
The following table identifies available user codes:
Code
[01]-[39], [41]-[95]
[40]

Programming User Codes:

LED Keypad:
Press [,][5] followed by the Master Code. The Program light will flash. The keypad will turn ON the corresponding zone lights to indicate if
any user codes are programmed. To add or change a user code, enter the 2-digit user code to be programmed. The zone light will flash. Enter
a new 4 or 6-digit user code or press [,] to delete the user code. After the user code is programmed or deleted, the zone light corresponding to
the user code will stop flashing. To add or change another user code, enter the 2-digit user code to be programmed or press [#] to exit.
LCD Keypad:
Press [,][5] followed by the Master Code. The keypad will display the first user (user 01) and include the letter 'P' in the bottom, right cor-
ner if the user code is programmed. Scroll to the appropriate user and press the [,] key to program the user (or enter the 2-digit user num-
ber). Enter a new 4 or 6-digit user code or press [,] to delete the user code. After the user code is programmed or deleted, scroll to another
user or press [#] to exit.
Programming Partition Assignment:
Press [,][5] followed by the Master Code or Supervisor Code. Press [98] followed by the 2-digit user to change to the partition assignment.
The keypad will turn ON the corresponding zone light to indicate which partition(s) the user is assigned to. For example, if zone light 1 is
ON, the user is assigned to partition 1. To change the partition assignment, press the number corresponding to the partition. Once the correct
partitions are assigned to the user, press [#] to exit. To change the partition assignment for another user, press [98] followed by the 2-digit
user number. When finished, press [#] to exit.
Programming User Attributes:
Press [,][5] followed by the Master Code or Supervisor Code. Press [99] followed by the 2-digit user to change to the user attributes. The
keypad will turn ON the corresponding zone light to indicate which attributes are assigned to the user.
Light [1]
Light [2]
Light [3]
Light [4]
Light [5]
Light [6]
Light [7]
Light [8]
To change the user attributes, press the number corresponding to the attribute. Once the correct attributes are assigned to the user, press [
exit. To change the user attributes for another user, press [99] followed by the 2-digit user number. When finished, press [
,
] on any PK series keypad to access the time and date programming menu.
Type
General User Codes
Master Code
User can enter User Code Programming section with this code
Duress Reporting Code is sent whenever this code is entered
User can manually bypass zones
User can access the Escort5580 module remotely
For Future Use
For Future Use
The panel will squawk when the user arms/disarms
One-time use code – Can disarm the system once per day and is reset at midnight.
Function
Arm, disarm
All functions
7
Chapter 2 User Commands
] to
#
] to exit.
#