KVH Industries TracVision S3 Owner's Manual page 17

Figure 2-11
Figure 2-12
Figure 2-13
Figure 2-14
Figure 2-15
Figure 2-16
Figure 2-17
Figure 2-18
Figure 2-19
Figure 2-20
Figure 2-21
Figure 2-22
Figure 2-23
Figure 2-24a-d Attaching the KVH-provided F-connector
Figure 2-25
Figure 2-26
Figure 2-27
Figure 3-1
Figure 3-2
Figure 5-1
Figure 5-2
Figure 5-3
Figure 5-4
Figure 5-5
Figure 5-6
Figure 5-7
iv
TracVision S3 Shipping Restraints
(Storage Position) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-7
Proper Wire-to-Terminal Connection . . . . . . . . . . . . . . . . .2-8
Moving the Antenna Reflector . . . . . . . . . . . . . . . . . . . . . .2-8
Cable Port Assignments (Exterior of Baseplate) . . . . . . . .2-8
Cable Overlap within the TracVision S3 Baseplate . . . . . .2-9
Switchplate Panel Cutout Dimensions . . . . . . . . . . . . . . . .2-9
Proper Terminal Strip Wiring Arrangement
- Data Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-10
Antenna Data Cable Wiring Arrangement . . . . . . . . . . . .2-11
Proper Terminal Strip Wiring Arrangement
- Power Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-11
Power Cable Wiring Arrangement . . . . . . . . . . . . . . . . . .2-12
Vehicle Power Wiring Arrangement . . . . . . . . . . . . . . . . .2-12
Mounting the Switchplate Support Frame
and Front Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-13
Connecting the RF Cable to TracVision S3 . . . . . . . . . . .2-14
to an RF Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-14
Installing Three or More IRDs Using an Active
Multiswitch (North American Systems Only) . . . . . . . . . .2-16
Skew Adjustment (European Systems Only) . . . . . . . . . .2-24
Remote Dish Wiring Configuration . . . . . . . . . . . . . . . . .2-26
Be Aware of Objects that Might Block
the Satellite Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-1
Turning on the TracVision S3 Using the Switchplate . . . . .3-1
Antenna, PCB, and Rotating Plate . . . . . . . . . . . . . . . . . .5-3
Close-up of Connecting Rod and E-ring . . . . . . . . . . . . . .5-3
Antenna Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-4
Close-up of RF Detector and PCB . . . . . . . . . . . . . . . . . .5-4
Removing the PCB Cover . . . . . . . . . . . . . . . . . . . . . . . . .5-5
PCB and RF Detector Board Connector Locations . . . . . .5-6
LNB Skew Angle Setting (European Systems Only) . . . . .5-7