Quinny ZAPP Instructions Manual page 6

>> GB
Preparing the pushchair for use and instructions for use
The illustration numbers correspond to the text
(see illustrations on pages 3 to 5).
Please note: The left and right sides are as seen from the
handlebar/back of the Zapp.
Start:
Mounting the wheels onto the frame
(1) Insert the rear wheel with axle into the Zapp frame
until you hear a 'click'.
(2) Slide the double front wheel onto the front axle of
the Zapp frame until you hear a 'click'.
Unfolding the frame
(3) Gently lift the Zapp by the adapter attachments.
The frame will unfold itself.
(4) Pull the coupling outwards until you hear a 'click'.
(5) Press release button 1. The button will stay pressed
by itself.
(6) Press release button 2, whilst at the same time raising
the upper section of the Zapp. Release button 2 and
lift up further until you hear a 'click'.
(7) Extend the upper lock into the horizontal position.
The Zapp is now ready for use.
Parking brake
Always use the parking brake, even when standing still for
only a few moments!
(8) Push down on the red button (P) to set the parking
brake. Push down on the other pedal to release the
brake.
Maxi-Cosi:
Using with a Maxi-Cosi car seat
Maxi-Cosi infant carriers are suitable for children from birth
to 15 months and weighing up to 13 kg (as indicated on the
Maxi-Cosi car seat).
Installing the adapters
(9) Slide off the covers of the adapter attachments and
store them carefully in the storage compartment in
the Zapp carrying bag.
(10) Slide the adapters into the adapter attachments until
you hear a 'click'.
Installing the Maxi-Cosi car seat
(11) Place the car seat onto the adapters with the head
end at the front until you hear a 'click'. Check to
make sure everything is attached securely.
Removing the Maxi-Cosi car seat
(12) Press the control buttons on both sides while at the
same time lifting the car seat from the Zapp.
Removing the adapters
(13) Press the button and slide the adapters out of the
adapter attachments.
(14) Slide the covers back onto the adapter attachments.
Zapp pushchair seat:
Using as a pushchair
The Zapp seat is suitable for children ages 6 months to
4 years (maximum of 20 kg). The Zapp seat can be used
as soon as your child is able to sit up unassisted.
10
Preparing the Zapp seat for use
(15) Fasten the cover to the foot end of the seat.
(16) Place the Zapp in a half-open position and tilt the
frame until it is resting on the rear wheels and
adapter attachments.
(17) The ends of the cover have markings that correspond
to the markings at the end of the cover grooves.
(18) First slide each end piece into the corresponding
groove and then pull the cover into place.
(19) Slide the cover stops into the cover grooves.
(20) Fasten the hooks to the tubes and unfold the Zapp
completely.
Using the Zapp:
Hood
(21) Slide off the covers of the adapter attachments and
store them carefully.
(22) Slide both ends of the hood into the adapter
attachments until you hear a 'click'.
(23) Fasten the hood to the top of the Zapp using the
snaps and Velcro. Check to make sure the hood is
fastened securely.
(24) The hood can be adjusted to two different positions:
folded out or folded back. Note: The Zapp can be
folded without removing the hood. To remove the
hood, unfasten the snaps and Velcro and pull the
hood out of the adapter attachments. Slide the
covers back onto the adapter attachments.
GB <<
Placing your child in the Zapp
Set the brake on the Zapp before placing your child in it.
Make sure the safety harness is unhooked before placing
your child in the pushchair seat.
(25) Slide the buckle sections together. Fasten the lap and
shoulder belts to the crotch strap by 'clicking' the
buckle sections into the buckle.
(26) Adjust the belts to the size of your child by
lengthening or shortening them using the clasps.
(27) Push both buttons to open the belt buckle. There are
D-rings for attaching an additional safety harness.
Make sure it complies with all safety standards
(i.e. the BS 6684) before using it.
(28) Important! The fasteners on the side of the safety
harnesses are for attaching the footmuff only.
Locking the swivel wheel
It is advisable to lock the swivel wheel into a fixed position
when using the pushchair in a straight direction for a
longer period.
(29) Push the swivel wheel lock downwards and turn
the front wheel into the backward position until you
hear a 'click'. The front wheel is now locked into the
fixed position. To unlock the swivel wheel, push the
swivel wheel lock upwards.
11