Konica Minolta FK-502 Service Manual page 167

Setting Address
--- 0e0002 No. of error lines-good
--- 0e0003 No. of error lines-bad
--- 0e0004 Rate of error lines-very good
--- 0e0005 Rate of error lines-good
--- 0e0006 No. of continuous error lines-bad
--- 0e0007 No. of continuous error lines-bad
--- 0e0008 No. of continuous error lines-bad
--- 0e0009 No. of continuous error lines-bad
Utility Mode Spe-
cial Setting 0e000a EP tone addition
(0,2)
--- 0e000b CED detection-transmission frequency
--- 0e000c TSI/CSI/CIG parameter
Utility Mode Spe-
cial Setting 0e000d G3ModeError
(6)
--- 0e000e Step up/down
Utility Mode Spe-
0e000f Delay timer between DCS-TCF
cial Setting
Utility Mode Spe-
0e0010 Delay timer between PIX-PMC
cial Setting
Utility Mode Spe-
0e0011 Delay timer between CED-DIS
cial Setting
Utility Mode Spe-
0e0012 T1 timer for calling
cial Setting
Utility Mode Spe-
0e0013 T1 timer for called
cial Setting
--- 0e0014 ph.C reception limited time
Utility Mode Spe-
0e0015 Timer between EOLs
cial Setting
--- 0e0016 Timer between frames
Utility Mode Spe-
0e0017 ANSam signal transmission time
cial Setting
Item
bit7 bit6
No. of good judgment error lines (HEX)
VeryGoodErrorNum<No. of error linesGoodErrorNum, RTP is transmitted
No. of bad judgment error lines (HEX)
GoodErrorNum<No. of error lines BadErrorNum, RTN is transmitted. No. of error lines>BadErrorNum, it is considered to be error line over.
Rate of very good judgment error lines (HEX, %)
Rate of error linesVeryGoodErrorPercent, MCF is transmitted.
Rate of good judgment error lines (HEX, %)
VeryGoodErrorPercent<Rate of error linesGoodErrorPercent, RTP is transmitted.
Rate of error lines>GoodErrorPercent, RTN is transmitted.
No. of bad judgment sequential error lines (HEX) Normal
No. of sequential error linesErrorContNormal, MCF is transmitted.
No. of sequential error lines>ErrorContNormal, RTN is transmitted.
No. of bad judgment sequential error lines (HEX) Fine
No. of sequential error linesErrorContNormal, MCF is transmitted.
No. of sequential error lines>ErrorContNormal, RTN is transmitted.
No. of bad judgment sequential error lines (HEX) 300dpi
No. of sequential error linesErrorContNormal, MCF is transmitted.
No. of sequential error lines>ErrorContNormal, RTN is transmitted.
No. of bad judgment sequential error lines (HEX) Super fine
No. of sequential error linesErrorContNormal, MCF is transmitted.
No. of sequential error lines>ErrorContNormal, RTN is transmitted.
TSI transmission CSI Transmission
0: No 0: No
1: Always 1: Always
Ph-C8 min. limit Selection of "-" at
timer at NonECM dial top
0: No 0:OFF
1: Yes 1:ON
Strict TCF check
DCS - TCF delay timer Unit: 10 ms, HEX)
PIX - PMC delay timer Unit: (10 ms, HEX)
CED - DIS delay timer (Unit: 10 ms, HEX)
T1 timer for transmission (Unit: 1sec, HEX)
T1 timer for reception (Unit: 1 sec, HEX)
Max. reception time per page (Unit: min, HEX) 1to255 min.
EOL - EOL timer (Unit: 100 ms, HEX)
Timer between frames (Unit: 1 sec, HEX)
ANSam signal transmission time (Unit: 100 ms, HEX)
Contents
bit5 bit4 bit3
V.17
CIG Transmission
0: No
1: Always
DIS retransmis-
RTN reception
Remote reception sion interval in
0:step down DCN transmis-
ID received manual reception
1: Line discon- sion at T200
1: No limit 0:4.5 sec.
nect.
1:3.0 sec.
bit2 bit1 bit0 Japan
0x40
0x80
0x05
0x0a
0x03
0x06
0x09
0x0c
V.33 V.29 0x06
CED transmis-
CED detection
sion frequency
0: Detect 0x00
0:2100Hz,
1: Not detect
1:1100Hz
Character ID is
0xe0
put on CSI.
DIS length at
reception limited
DCN transmitted
to 4byte 0x00
at stop of ph.C
0: No limit
1: Limit
0x00
0x08
0x08
0x08
0x23
0x23
0x0f
0x82
0x23
0x28
Default
North Amer-
Europe
ica
0x40 0x40
0x80 0x80
0x05 0x05
0x0a 0x0a
0x03 0x03
0x06 0x06
0x09 0x09
0x0c 0x0c
0x06 0x06
0x00 0x00
0xe0 0xe0
0x00 0x00
0x00 0x00
0x08 0x08
0x08 0x08
0x08 0x08
0x23 0x23
0x23 0x23
0x0f 0x0f
0x82 0x82
0x23 0x23
0x28 0x28