Program/Random/Relay Play/Power On Play - Denon DN-D9000 Operating Instructions Manual

PROGRAM/RANDOM/RELAY PLAY/POWER ON PLAY

16
3
-TRACK HOT START
SAMPLER
RVS SAMP1 SAMP2 B EXIT/RELOOP
STOP
EXIT/
FLIP A 3 A 4 B CUE
RELOOP
CLR A3 A4 CUE
A 3/4
EXIT/
FLIP A 1 A 2 B
RELOOP
CLR A1 A2 4 HOT START PITCH/VOL
A3 B A4 B
A1 B A2 B
TOTAL REMAIN ELAPSED CONT. SINGLE KEY ADJ. DRAG S.
m s
BRAKE
m s f
ECHO
MEMO DUMP
PROG RVS
CONT./SINGLE TIME MEMO PROGRAM PLATTER MODE
RELAY TOTAL TIME PRESET RANDOM ALL OFF
CUE
TAP
STUTTER PLAY/PAUSE AUTO
q, e
Program Play
• Up to 25 tracks from one disc can be programmed.
• Programs for up to six discs (one program per disc) can be stored in the non-volatile memory for later recall.
NOTE: Such functions as Hot Start, Sampler, Effector and Platter Effect do not operate during programmed
playback.
Program mode select
q Push the PROGRAM button in Cue or pause mode to enter Program mode.
w Turn the PARAMETERS knob to select the various program setting modes as follows.
Prog.In, Prog.On, Prog.Off, MemoSet, MemoCall, Memo Clr
Depending on conditions, some modes cannot be selected.
e Push the PROGRAM button again to exit program mode.
Input Program (Prog.In)
Input the program for program playback.
r Turn the PARAMETERS
PARAMETERS
knob to select the track.
PUSH
ON/OFF
t Push the PARAMETERS
PARAMETERS TRACK
knob to input the
1 selected track to the PUSH
-1
ON/OFF
program.
1 Insert Tracks to Program
• You can insert tracks to the previously
programmed tracks.
• One track can be inserted at a time
using the PITCH BEND + button and
return step 1.
w, r, t, y
2 1
-TRACK PLAY -TRACK HOT START
SAMPLER
PARAMETERS TRACK
RVS SAMP1 SAMP2 B
PUSH
ON/OFF
OPEN/
FLIP A 3 A 4 B
CLOSE
CLR A3 A4 CUE
A/B TRIM
PITCH/KEY PITCH BEND
FLIP A 1 A 2 B
SPLICE CLR A1 A2
RANGE
A3 B
A1 B
TOTAL REMAIN ELAPSED CONT. SINGLE KEY ADJ.
m s
m s f
MEMO
PROG
0%
CONT./SINGLE TIME MEMO PROGRAM
RELAY TOTAL TIME PRESET RANDOM
CUE
STUTTER PLAY/PAUSE
REMOTE CONTROLLER RC-D90
2 Clear Tracks from Program
• You can clear tracks from the previously
1
programmed tracks.
-2
TRACK • One track can be cleared at a time using
the PITCH BEND - button.
y Push the PARAMETERS
PARAMETERS
knob again to return step
PUSH
1- r.
ON/OFF
• Repeat these steps to
input whole program.
2
• Push the PROGRAM button to end the
program input mode, then proceed to
Start Program Play (Prog.On).
Start Program Play (Prog.On)
• When "Prog.On" is selected, DN-D9000 will
cue up at the first track in the program.
• Program playback
3
PLAY/PAUSE button is pushed.
-TRAC
EXIT/RELOOP
STOP 3 You can use program repeat play function
EXIT/
CUE
RELOOP
with push EXIT/RELOOP button.
A 3/4 A/B TR
EXIT/
RELOOP
4 HOT START PITCH/VOL SPLIC Cancel Program mode (Prog.Off)
A4 B
• When "Prog.Off" is selected, the program
A2 B
4
DRAG S.
play mode turns off and returns to normal
BRAKE
ECHO
DUMP
play mode.
RVS
PLATTER MODE
Store Program (MemoSet)
ALL OFF
• When "Memo Set" is selected, the program
TAP
5
that has been set is stored in the non-volatile
AUTO
memory.
Call Program (MemoCall)
• When "MemoCall" is selected, the program
6
stored in the non-volatile memory is loaded
and the program play mode is set.
Clear Program (Memo Clr)
• When "Memo Clr" is selected, the program
7
for the loaded disc is cleared.
• To clear all Program Memo use Preset
function.
TRACK
starts when the
ENGLISH
23