A-B Trim - Denon DN-D9000 Operating Instructions Manual

ENGLISH
A/B TRIM
10
• The seamless loop, sampler loop and splice A and B points can be fine-adjusted using Jog Wheel.
• There are two ways for doing this.

A-B Trim:

Trim the points during loop playback as a rehearsal.
A/B Move: Move the points using the Manual Search. A/B Move can not be used with Sampler loop.
A/B TRIM
-TRACK HOT START
e, t, o, !2 RVS
FLIP
CLR
FLIP
CLR
A3
A1
MEMO
PROG
CONT./SINGLE
RELAY
Select A-B trim mode
First select whether to adjust the A and B
points using the A-B trim mode or the A/B
move mode.
q Push the A/B TRIM button to
set the A and B point position
1
adjustment mode.
w Now turn the
PARAMETERS
PARAMETERS knob to
PUSH
select the A-B Trim or the ON/OFF
A/B Move.
Select A point (in A-B Trim)
e Select the A-B Trim and push
the corresponding A button
for the loop to be trimmed.
The A button illumination
2 flashes and loop playback
starts.
• In the splice trim mode, total 6 seconds
of spliced section (started from 2
seconds before A point to 4 seconds
after the B point) is played.
16
y, i, !0 , !2 q, !3 w
-TRACK PLAY
SAMPLER
PARAMETERS TRACK
SAMP1 SAMP2 B EXIT/RELOOP
STOP
PUSH
ON/OFF
EXIT/
A 3 A 4 B CUE
RELOOP
A3 A4 CUE
A 3/4 A/B TRIM
PITCH/KEY PITCH BEND
EXIT/
A 1 A 2 B
RELOOP
A1 A2 4 HOT START PITCH/VOL SPLICE
RANGE
B A4 B
B A2 B
TOTAL REMAIN ELAPSED CONT. SINGLE KEY ADJ. DRAG S.
m s
BRAKE
m s f
ECHO
DUMP
RVS
TIME MEMO PROGRAM PLATTER MODE
TOTAL TIME PRESET RANDOM ALL OFF
CUE
TAP
STUTTER PLAY/PAUSE AUTO
REMOTE CONTROLLER RC-D90
r, u, !1
Trim A point
r Turn the Jog Wheel to
move the A point 1 frame
at a time.
A/B TRIM
• Range for trimming A point is limited as
follows.
SPLICE
A point for Loop:
±30 frames from the original A point.
TRACK (However, when the A point was
3
loaded from the standby mode, the A
point cannot be moved backwards.
So, use A/B Move function)
A point for Splice:
Between the beginning of the disc and
5 frames before B point.
A 1 A point for Sampler:
Between the original A point and 5
frames before B point.
Save the A point
t Push the A button again to
save new A point, and the
4
unit automatically exit from
the A-B Trim mode.
Select B point (in A-B Trim)
y Select the A-B Trim mode and
to select the B point, push the
B button after selecting the A
5
point.
Then push the B button. The B LED
flashes and the B point trim become
enable.
Trim B point
u Turn Jog Wheel to move
the B point 1 frame at a
-TRACK HOT START
S time.
RVS SAMP1 SAMP2
OPEN/
FLIP A 3 A 4
CLOSE
CLR A3 A4 CUE
• Range for trimming B point is limited as
FLIP A 1 A 2
follows.
CLR A1 A2
B point for Loop:
A3 B
A1 B
Between 5 frames after A point and
TOTAL REMAIN ELAPSED CON
m 6
m s
disc end.
MEMO
PROG
B point for Splice:
0%
CONT./SINGLE TIME MEMO
±30 frames from the original B point.
RELAY TOTAL TIME PRESET
(However, when the B point was loaded
CUE
from the standby mode, the B point
cannot be moved backwards. So, use
STUTTER PLA
A/B Move function)
B point for Sampler:
Between 5 frames after A point and
sampler end.
Save the B point
i Push the B button again to
7 save new B point, and the
unit automatically exit from
finish the A-B Trim mode.
A 1
A/B Move
B
Select A and B points
o Select or the A/B Move and
push the A button for the A
point you want to move. The
standby mode is set at the A
point and the A button
illumination flashes.
8
!0 To select the B point, push
the B button after selecting
the A point.
• The B LED flashes. The
Selected B point is used for the A1 or A2
point that was first selected.
Move A or B points
!1 Turn the Jog Wheel to move
the selected point using the
Manual Search function.
• Range for moving A point is limited as
follows.
A point for Loop:
Between the beginning of the disc and
5 frames before B point.
A point for Splice:
9
Between the beginning of the disc and
5 frames before B point
• Range for moving B point is limited as
follows.
B
B point for Loop:
Between 5 frames after A point and
disc end
B point for Splice:
Between 5 frames after A point and
disc end
Save the A or B points
!2 Push the A1/A2 or B button
again. The LED stops flashing
10
and the A1/A2 or B point is
saved, and the unit
automatically exit from the A/B
Move mode.
Cancel the A-B Trim or A/B Move
!3 Push the A/B TRIM button to
11
cancel the mode.
A 1
B
B
A/B TRIM
SPLICE