Denon DN-D9000 Operating Instructions Manual page 9

#6
EXIT/RELOOP button
• Use this to exit, back again to Seamless Loop
playback for A1 and A2 with keeping all loop
settings. You can add variety looping with this
function.
• The LED indicates what's going on about
looping.
EXIT/RELOOP LED lit:
Seamless Loop on or playing.
EXIT/RELOOP LED flashing:
Playback after exit loop.
• This button also switches repeat play modes
on and off in Program, Random mode.
#7
(SAMP) RVS/FLIP/CLR button
• (SAMP)RVS:
Use this to select the sample play direction
forward and reverse. When select reverse
RVS LED lights up.
• FLIP:
If in 4 Hot Start mode or Alpha-Track Hot Start
mode, this button works as FLIP button for A3,
A4. You can select Hot Start or Stutter mode.
When Hot start mode is selected FLIP LED
lights up.
• If the FLIP button is pushed while pushing the
A3, A4 or Alpha-Cue button, the selected A
point or the Alpha-Cue point is cleared.
By holding down just the FLIP button for more
than 1 sec, you can clear A3 and A4 points all
at once.
#8
SAMP1/A3 button
#9
SAMP2/A4 button
• SAMP1/SAMP2:
In the sampler mode, push these buttons to
record or play sound of Sampler 1 or 2.
• A3, A4:
When in the 4 Hot Start or Alpha-Track Hot
Start modes, these act as A3 or A4 button. You
can use these buttons for Hot Start, Seamless
Loop and Stutter playback.
• These 4 buttons illumination color changes in
the different modes.
..
Orange 4 Hot Start mode
Green ....Alpha-Track Hot Start or Sampler
mode
$0
(SAMP) B, B button
• (SAMP)B:
In the Sampler mode, use this to set the
sampler loop B point.
• B:
In the 4 Hot Start or Alpha-Track Hot Start
modes, use this to set the B point for A3 or A4
button seamless looping.
$1
(SAMP) EXIT/RELOOP,
EXIT/RELOOP button
• (SAMP)EXIT/RELOOP:
Use this to turn the Sampler Loop mode on
and off. Also acts as EXIT/RELOOP button for
Sampler Loop to exit or back again.
• EXIT/RELOOP:
In the 4 Hot Start or Alpha-Track Hot Start
modes, use this to exit or back again Seamless
Loop for A3 and A4.
• EXIT/RELOOP LED indicates conditions of
loop.
EXIT/RELOOP LED lit:
Seamless Loop on or playing.
EXIT/RELOOP LED flashing:
Playback after exit loop.
$2
A3/4, PITCH/VOL button
• A3/4:
After a short push, A3, A4 button operating
mode can be selected with the PARAMETERS
knob from Sampler, 4 Hot Start, Alpha-Track
Hot Start.
• PITCH/VOL:
After pushing for more than 1 sec, pitch and
output level of Sampler, Alpha-Track playback
can be adjusted with the PARAMETERS knob.
$3
A/B TRIM, SPLICE button
• A/B TRIM:
With a short push of this button, the A
and B point trim mode changes on and
off while in PLAY or CUE mode.
•
SPLICE:
When pushed for more than 1 sec ,
Splice point setting mode for A1 and A2
starts.
$4
a a (Alpha) CUE/SAMP STOP/
STUTTER button
• a a (Alpha) CUE/STUTTER:
Use this as CUE and STUTTER button in
Alpha-Track.
• SAMP STOP:
Push while Sampler playback, Sampler
playback stops.
• This button lights up when the Alpha-CUE
point is set.
$5
a a (Alpha) TRACK PLAY/PAUSE
button
• When this button is pushed while in the Cue
or Pause mode, the Alpha-Track playback
starts. By pushing it once again will Pause the
Alpha-Track.
• It is necessary to make Cue point for the
Alpha-Track before starting Alpha-Track
playback.
$6
a a (Alpha) MODE button
• Use this to turn the Alpha-Mode on and off.
The Alpha-Mode playback sounds
outputted from the MONITOR OUT jacks in the
Alpha-Mode.
(4) RC-D90 Rear panel
$7
are REMOTE connector
• Connect this connector to the REMOTE
connector on the DN-D9000 using the included
cord.
ENGLISH
9