Pressed - Denon DN-2600F Operating Instructions Manual

!3
Jog dial (inner side)
• In the search mode, turn this dial during the search operation
to move the playing point in units of frames.
• In the pitch bend and plat-H modes, turn this to change the
playing speed.
• In the key mode, turn this to adjust the key.
• In the scratch mode, turn this to scratch.
!4
Filter/Reverse button
(FIL/REVERSE)
• In the sampler mode, press this button to turn the sampler
reverse play mode on and off.
• In the effector mode, press this button to set the filter
parameter input mode.
!5
Reverb/Loop button (RVB/LOOP)
• In the sampler mode, press this button to turn the sampler
loop play mode on and off.
• In the effector mode, press this button to set the reverb
parameter input mode.
!6
TAP (TAP/BPM)/STOP button
• In the sampler mode, press this button to stop sample
recording/playback.
• In the sampler mode, press this button for over 2 seconds to
delete the sample data.
• In cases other than the above, the tempo at which the button
is pressed is measured and this is input as the BPM. When
the button is pressed only once, the BPM is displayed.
!7
CUE button
• Pressing the CUE button during play provides a return to the
position at which play was started. Alternately pressing the
PLAY/PAUSE button and the CUE button allows the CD to be
played from the same position any number of times.
• The button lit, when the standby mode is set.
• When in the sleep mode, cancel the sleep mode.
!8
Flanger/Pitch button (FLG/PITCH)
• In the sampler mode, press this button to set the sampler
parameter input mode.
• In the effector mode, press this button to set the flanger
parameter input mode.
!9
PLAY/PAUSE button (
• Use this button to start playback.
• Press once to start playback, once again to set the pause
mode, and once more to resume playback.
• In the brake mode, press this button to brake.
@0
ON/OFF, PLAY/WRITE button
• In the sampler mode, press this button to start sample
recording/playback.
• Press this button to turn the various effectors on and off.
@1
PRESET button
• Press this button once to turn the preset input mode on.
Press it again to turn the preset input mode off.
@2
MODE button
• When this button is pressed, the ASP operation selection
mode is set.
)
13
@3
Track select/Data master knob
( – /PUSH ENTER)
8 9
• Turn this knob to select the next track to be played.
• Turn the knob clockwise by one click to move one track
forward, counterclockwise by one click to move one track
backward.
• When the knob turned while pressing it in, one click
corresponds to 10 tracks.
• In the preset mode, use this knob to set and enter preset
settings.
• When setting programs, use this knob to select, enter and
check the program.
• In the memo mode, use the knob to set the item, to enter
the setting, to check the setting and to delete the setting.
• This knob is used to select the ASP operation mode and to
set data in various modes.
@4
Pitch slider
• Use this to adjust the playing speed.
• The playing speed decreases when slid upwards and
increases when slid downwards.
@5
PITCH BEND + button
• The playing speed increases while this button is pressed.
• When the button is released, the playing speed returns to
the previous speed.
@6
Key control button (KEY)
• When this button is pressed, the key control mode is set and
the key can be adjusted with the jog dial.
• When pressed again, the key adjust mode is turned on and
the key remains the same even if the pitch is changed. (KEY
ADJUST)
@7
PITCH button
• Press this button to switch to the play speed set with the
Pitch slider. The PITCH LED lights.
• When the button is pressed again, the fixed pitch mode is
set and the PITCH LED flashes.
• Press the button again to cancel the pitch play mode and
return to normal speed.
@8
PITCH BEND – button
• The playing speed decreases while this button is pressed.
• When the button is released, the playing speed returns to
the previous speed.
@9
BRAKE button
• Press this button to select the brake mode (BRAKE/PLAT-S
mode).
#0
MEMO button
• Press this button to set the memo mode.
• The following data is stored in the memory:
Standby position, A-1 point, A-2 point, B point, playing pitch.
#1
PROGRAM button
• Press this button to set the program mode.
ENGLISH
9