Part Names And Functions; Pressed - Denon DN-2600F Operating Instructions Manual

ENGLISH

3 PART NAMES AND FUNCTIONS

(1) DN-2600F Front Panel
q
POWER button (
• Press this button to turn the power on.
NOTE:
• Be sure to close the disc holders before turning off the
power.
w
POWER indicator
• This lights when the power is on.
e
Disc holder
• Place discs in this holder.
• Press the disc holder OPEN/CLOSE button to open and close
the disc holder.
CAUTION:
• Do not place foreign objects in the disc holders. Doing so
could damage the player.
• Do not push the disc tray in manually when the power is off,
as this may result in malfunction and damage the player.
r
Disc holder LED
• This flashes while the disc holder is opening and closing.
• The LED lights when the disc holder is open and serves as
the disc holder illumination.
t
Disc holder OPEN/CLOSE button
• Press this button to open and close the disc holder.
• The disc holder will not open during playback. Stop playback
before pressing this button.
(2) DN-2600F Rear Panel
y
Analog output jacks 1, 2
(ANALOG OUT 1, 2)
• These are unbalanced output jacks. The audio signals from
the CD players are output from these jacks.
u
Digital output jacks 1, 2
(DIGITAL OUT 1, 2)
• Digital data is output from these jacks according to the
presettings.
• We recommend using a 75Ω/ohm pin cord (available in
stores) for connections.
NOTES:
• Turn PITCH control OFF when making digital recordings.
Most digital recorders will not accept a variable pitched
digital signal.
• The functions are limited when outputting digital data. (The
loop, brake, Plat, Bend-Jog, scratch, sampler, effector and
key control functions cannot be used.)
i
Fader input jacks 1, 2
(FADER 1, 2)
• Use this when using the unit with a console fader. (Mini
Jack)
(FADER INPUT LEVEL HCMOS (Ii=–3mA))
8
ON OFF)
¢ £
• The fader can be activated using the switch circuit shown on
the diagram below.
SW 1
SW 2
*
GND
• Connect SW1 to the "Lch" stereo mini jack.
• Connect SW2 to the "GND" stereo mini jack.
• Connect GND* to the analog output "GND" terminal.
• Do not use the "Rch" jack.
• When SW1 is pressed, the hot start play mode selected with
the A1 and A2 buttons starts.
• When SW2 is pressed, the hot start play mode stops.
Load the hot start data before starting fader playback.
o
Remote control connector (REMOTE)
• Connect this connector to the RC-46 control unit using the
included control cord.
(3) RC-46 Front Panel
!0
EFFECT button
• Press this button is pressed to select the jog dial operating
mode.
Pitch bend mode:
When the jog dial is turned, the playing speed changes at a
fixed rate. (The BEND LED lights.)
Plat-H mode:
When the jog dial is turned, the playing speed changes in
function of the speed at which the jog dial is turned.
(The BEND LED and the "
Key mode:
The key can be adjusted by turning the jog dial. (The KEY
LED lights.)
Scratch mode:
Scratching is possible by turning the jog dial. (The DIGI-S
LED lights.)
!1
SEARCH button
• When this button is pressed while the jog dial operating
mode is set to pitch bend, plat-H, key or scratch, the jog and
shuttle dial operating mode is set to the search mode.
!2
Shuttle dial (outer side)
• The shuttle dial can be used in the search mode.
• Use this dial to select the scanning direction and speed.
• The disc is scanned in the forward direction when the shuttle
dial is turned clockwise from the neutral position, and in the
reverse direction when the shuttle dial is turned
counterclockwise.
• The scanning speed increases as the wheel is turned further.
Lch
GND
" indicator light.)
PLAT-H