Denon DN-2600F Operating Instructions Manual page 20

ENGLISH
Select the high frequency range to be filtered.
Turn the data master knob (
• If the data master knob (
player returns to the same status as in step 1-2.
• The frequency can be set between 100 Hz and 20 kHz (or
2-
none).
2
The high frequency cannot be set below than the low
frequency.
NOTE:
• For some tracks, clipping may occur in the playback
sound.
Start filtered playback.
Press the ON/OFF button at any point between steps 1-1
and 2-2.
3
FIL ON
• When pressed again, the filter turns off.
Canceling the filter frequency input mode.
Press the FIL/REVERSE button.
4
• The " " indicator is lit when the filter is on.
• The " " indicator is not lit when the filter is off.
Using the reverb function
With this function, an echo is produced at the set tempo.
Set the reverb delay time input mode.
Press the RVB/LOOP button.
1-
1 ***bpm 1/2
Select the reverb delay time.
Turn the data master knob (
1-
2
• The time can be set to 2/1, 1/1, 3/4, 1/2, 1/4 or 1/8 the
BPM set with the TAP (TAP/BPM) button.
Set the reverb feedback number mode.
Press the data master knob (
2-
1
Feedback number
Select the reverb feedback number.
Turn the data master knob (
PUSH ENTER
The feedback number increases when the
2-
knob is turned clockwise and decreases
2
when the knob is turned counterclockwise.
• If the data master knob (
player returns to the same status as in step 1-2.
20
— ).
8 9
— ) is pressed again, the
8 9
FIL OFF
EFFECT
Flashing
— ).
8 9
***bpm 1/2
— ).
8 9
L F.Back H
— ).
8 9
— ) is pressed again, the
8 9
Start reverb playback.
Press the ON/OFF button at any point between steps 1-1
and 2-2.
3
RVB ON
• When pressed again, reverb playback stops.
Canceling the reverb data setting mode.
Press the RVB/LOOP button.
4 • The " " indicator is lit when the reverb mode is on.
• The " " indicator is not lit when the reverb mode is
off.
Using the flanger function
With this function you can create swelling sounds.
Set the flanger time input mode.
Press the FLG/PITCH button.
***bpm 1/4
1-
1
Select the flanger time.
Turn the data master knob (
1-
2
• The time can be set to 4/1, 2/1, 1/1, 3/4, 1/2, 1/4 or 1/8
the BPM set with the TAP (TAP/BPM) button.
Set the flanger gain input mode.
Press the data master knob (
2-
1
L
Gain
Select the flanger gain.
Turn the data master knob (
PUSH ENTER
The gain increases when the knob is turned
2-
clockwise and decreases when the knob is
2
turned counterclockwise.
• If the data master knob (
player returns to the same status as in step 1-2.
Start flanger playback.
Press the ON/OFF button.
3
FLG ON
• When pressed again, flanger playback stops.
Canceling the flanger data setting mode.
Press the FLG/PITCH button.
4
• The " " indicator is lit when the flanger mode is on.
• The " " indicator is not lit when the flanger mode is
off.
NOTE:
• For some tracks, clipping may occur in the playback sound.
RVB OFF
EFFECT
Flashing
— ).
8 9
— ).
8 9
Gain H
— ).
8 9
— ) is pressed again, the
8 9
FLG OFF