Entering Station Names - Integra DTM-5.3 Instruction Manual

Entering station names

Standby/On
Standby
Speakers
A B
Zone 2 Off Display
Phones
DVD
Display
While receiving a preset FM or AM station, a maximum of eight
characters consisting of letters, numbers and some symbols can be
stored to represent the station name.
Characters which can be entered:
A B C D E F G H I J K L M N O P Q R S T UV W X Y Z
/
1 2 3 4 5 6 7 8 9 0 –
*
Note: For the remote controller, press the RCVR/Tape mode button
before performing the procedure in this section.
Entering characters
As an example, assume an FM station with a frequency of
89.5 MHz has been stored in preset number 2CH and will be given
the name "ONKYO."
1 Select the desired station.
(Refer to "Selecting preset stations" on page 22.)
SPEAKERS A
AUT AUTO
MONO MONO
2 Press the Character button.
The frequency disappears from the display and the cursor (_)
flashes.
Character SPEAKERS A
3 Continue pressing the 5MNO button until "O" is dis-
played.
With each press of the button, the character that appears in the
display changes in the following sequence:
5 M N O 5 ...
If a button is not pressed within one second, the cursor automat-
ically moves to the next position.
To delete a character, press the Direct Tuning button. After the
selected character is deleted, all characters to the right of the
deleted character move one space to the left.
SPEAKERS A
5 MNO
4 Continue pressing number buttons to enter the desired
characters.
To enter N, press the 5MNO button.
To enter K, press the 4JKL button
To enter Y, press the 9YX- button.
9 YZ -
5 MNO 4 JKL
Alphabetic letters/
Tuning
symbols buttons
Master Volume
1 ABC 2 DEF 3 GHI
4 JKL 5 MNO 6 PQR
7 STU 8 VWX 9 YZ-
Direct Tuning 0/10 / Scan
Clear
Direct Tuning Memory FM Mode Character
Bass
Tape 2
Video Monitor Tape 1 FM AM Phono CD
Character
Direct Tuning
Note: indicate a space.
FM MUTE TUNED
ON STEREO
MHz
CH
FM MUTE TUNED
ON STEREO
CH
FM MUTE TUNED
ON STEREO
CH
SPEAKERS A
5 MNO
DRCT
Tune
Tuning
Down
Treble Balance
L R
DTM-5.3
5 Press the Character button to store the entered characters.
Character
If a button is not pressed within 16 seconds, the operation will
end automatically.
• Press the Display button when you wish to check the frequency
while you are entering the characters.
Changing an entered character
1 Select the desired station.
(Refer to "Selecting preset stations" on page 22.)
2 Press the Character button.
The first character and the cursor flash alternately.
Character
3 Press the Tuning
buttons on the remote controller) to move the cursor to
the character that you wish to change.
The cursor moves to the right when the
to the left when the
Tuning
4 Enter the desired character.
The previous character is replaced with a new character.
9 YZ -
5 Press the Character button.
Character
Cleaning all characters
1 Select the desired station.
(Refer to "Selecting preset stations" on page 22.)
2 Press the Character button.
3 Hold down the Memory button and press the FM Mode
button.
All characters entered for the selected station are cleared.
4 Press the Character button one more time.
Number
buttons
RCVR/Tape
Character
Tuning
Up
SPEAKERS A FM MUTE TUNED
ON STEREO
SPEAKERS A FM MUTE TUNED
ON STEREO
AUT UTO
MONO MONO
SPEAKERS A
button (or Tuning Down and Up
button is pressed and
button is pressed.
SPEAKERS A
SPEAKERS A
SPEAKERS A
CH
CH
23