Table of Contents
Advertisement
OPERATING INSTRUCTIONS
FOR YOUR SAFETY READ BEFORE LIGHTING
with local codes, if any; if not,
follow the current CAN1-B149/ANSI Z 223.1
(Australia: AS5601-2004, New Zealand: NZS
5261/ NZS5266)
WARNING: If you do not follow these
may result causing property damage,
personal injury or loss of life. Improper
installation, adjustment, alteration, service
or maintenance can cause injury or property
manual provided with this appliance. For
assistance or additional information consult
supplier.
A) BEFORE LIGHTING smell all around the appliance
some gas is heavier than air and will settle on the
WHAT TO DO IF YOU SMELL GAS
- Do not try to light any appliance
- Do not touch any electric switch, do not use
- Immediately call your gas supplier from a
instructions.
department.
to inspect the appliance and to replace any part of
the control system and any gas control which has
This appliance needs fresh air for safe operation and
CAUTION: Hot while in operation. Do not
touch. Severe Burns may result. Due to
high surface temperatures keep children,
clothing and furniture, gasoline and other
See installation and operating instructions
accompanying appliance.
LIGHTING INSTRUCTIONS
STOP!
1)
Plug the power cord into a power outlet.
2)
Press and release the ON/OFF button once to
start the unit.
*
ON/OFF function may be controlled by either
Remote Wall Mount Control or ON/OFF control
on the Unit.
3)
After approximately 3 seconds the spark
ignition system will spark for 25 seconds to
light the main burner.
4)
If the main burner does not light, check the
gas and reset the unit.
TO TURN OFF GAS APPLIANCE
1)
Press the ON/OFF button once.
2)
Turn off all electric power to the unit if service
is to be performed.
DO NOT REMOVE THIS
INSTRUCTION PLATE
38
38
COPY OF LIGHTING PLATE INSTRUCTIONS
NORMAL OPERATING
It is possible that you will hear some sounds from
your gas appliance. This is perfectly normal due to
the fact that there are various gauges and types
of steel used within your appliance. Listed below
are some examples. All are normal operating
sounds and should not be considered as defects
in your appliance.
Blower:
Regency gas appliances use high tech blowers
to push heated air farther into the room. It is not
unusual for the fan to make a "whirring" sound
when ON. This sound will increase or decrease
in volume depending on the speed setting of
your fan speed control.
Burner Tray:
The burner tray is positioned directly under the
burner tube(s) and logs and is made of a differ-
ent gauge material from the rest of the fi rebox
and body. Therefore, the varying thicknesses of
steel will expand and contract at slightly different
rates which can cause "ticking" and "cracking"
sounds. You should also be aware that as there
are temperature changes within the unit these
sounds will likely re-occur. Again, this is normal
for steel fi reboxes.
Gas Control Valve:
As the gas control valve turns ON and OFF, a
dull clicking sound may be audible, this is normal
operation of a gas regulator or valve.
Unit Body/Firebox:
Different types and thicknesses of steel will
expand and contract at different rates resulting
in some "cracking" and "ticking" sounds will be
heard throughout the cycling process.
919-130
SOUNDS OF
GAS APPLIANCES
DO NOT SPRAY AEROSOLS IN THE VICINITY OF
THIS APPLIANCE WHILE IN OPERATION.
Appliances incorporating a live fuel effect (designed to oper-
"
ate with blue fl ames with slight yellow tips) may exhibit slight
carbon deposition."
RESETTING THE UNIT
If the appliance goes to 'lockout', the system
will have to be reset by depressing the reset
button - located on the right side of the unit
by glass frame.
*Important: Wait at least 5 min for any un-
burned gas to clear before resetting the
appliance.
1) Open the bottom louver on the unit.
2) Press and release the reset button - once.
The button is located near the gas valve.
3) Wait for approximately 3 seconds - the
pilot sparks can be heard and seen. It will
take approximately 2 to 3 seconds for the
fl ame to be lit.
NOTE: Wait 5 minutes between reset
attempts.
NOTE: If unit fails to light after 25 seconds; wait 5
min, then manually reset using red button
on the right hand side below glass frame.
WARNING:
Regency GF900L Gas Fireplace
Advertisement
Table of Contents
