Subaru Forester 2004 Service Manual page 33

ENGINE (DIAGNOSTIC)
7. LED OPERATION MODE FOR ENGINE
1) On the «Main Menu» display screen, select the {Each System Check} and press the [YES] key.
2) On the «System Selection Menu» display screen, select the {Engine} and press the [YES] key.
3) Press the [YES] key after the information of engine type was displayed.
4) On the «Engine Diagnosis» screen, select the {Current Data Display/Save}, and then press the [YES] key.
5) On the «Data Display» screen, select the {Data & LED Display} and press the [YES] key.
6) Using the scroll key, move the display screen up or down until the desired data is shown.
• A list of the support data is shown in the following table.
Description
Ignition switch signal
Test Mode Signal
Neutral position switch signal
Air conditioning switch signal
Air conditioning relay signal
Radiator main fan relay signal
Knocking signal
Radiator sub fan relay signal
Rear oxygen sensor rich signal
Starter switch signal
Idle switch signal
Crankshaft position sensor signal
Camshaft position sensor signal
Power steering switch signal
Rear defogger switch signal
Blower fan switch signal
Small light switch signal
Tumble generated valve actuator
signal
Tumble generated valve drive sig-
nal
Handle switch signal
AT/MT identification terminal
Wiper switch signal
A/C mid pressure switch signal
AT coordinate retard angle
demand
AT coordinate fuel cut demand
AT coordinate permission signal
VDC not torque down out put
VDC torque down demand
ETC motor relay signal
Clutch switch signal
Stop switch signal
Subaru Select Monitor
Display
Ignition Switch
Test Mode Signal
Neutral Position Switch
A/C Switch
A/C Compressor Signal
Radiator Fan Relay #1
Knocking Signal
Radiator Fan Relay #2
Rear O Rich Signal
2
Starter Switch Signal
Idle Switch Signal
Crankshaft Position Signal
Camshaft Position Signal
P/S Switch
Rear Defogger Switch
Blower Fan Switch
Light Switch
TGV Output
TGV Drive
Handle SW
AT Vehicle ID Signal
Wiper Switch
A/C Mid Pressure Switch
Retard Signal from AT
Fuel Cut Signal from AT
Torque Permission Signal
Ban of Torque Down
Request Torque Down VDC
ETC Motor Relay
Clutch Switch
Stop Light Switch
EN(H4DOTC 2.5)-32
Message LED "ON" requirements
ON or OFF When ignition switch is ON.
ON or OFF When test mode connector is connected.
ON or OFF When neutral position signal is entered.
ON or OFF When air conditioning switch is ON.
ON or OFF When air conditioning relay is in function.
ON or OFF When radiator main fan relay is in function.
ON or OFF When knocking signal is input.
ON or OFF When radiator sub fan relay is in function.
When rear oxygen sensor mixture ratio is
ON or OFF
rich.
ON or OFF When starter switch signal is entered.
ON or OFF When idle switch signal is entered.
When crankshaft position sensor signal is
ON or OFF
input.
When camshaft position sensor signal is
ON or OFF
entered.
ON or OFF When power steering switch is entered.
ON or OFF When rear defogger switch is ON.
ON or OFF When blower fan switch is ON.
ON or OFF When small light switch is ON.
ON or OFF When TGV actuator signal is entered.
Close or
When TGV moves and valve opens.
Open
Low Input
or High Illuminates in Low Input.
Input
ON or OFF ON (AT model).
ON or OFF When wiper switch is turned to ON.
When A/C mid pressure switch is turned to
ON or OFF
ON.
ON or OFF When AT retard angle signal is exists.
When AT coordinate fuel cut demand signal
ON or OFF
is exists.
When AT coordinate permission signal is
ON or OFF
exists.
When VDC not torque down output signal is
ON or OFF
exists.
When VDC torque down demand signal is
ON or OFF
exists.
When electronic throttle control relay is in
ON or OFF
function.
ON or OFF When clutch switch is ON.
ON or OFF When stop light switch is ON.