Setting Remote Control Codes - Yamaha RX-V1600 Owner's Manual

Setting remote control AMP codes
Select one of the following codes to set the remote control
AMP code for the component you want to use.
Set AMP/SOURCEfTV to AMP or SOURCE and then
change the remote control code settings.
AMP library
Remote
control
code
AMP 10
(remote
Function
control
(this unit's
setting)
setting:
see page 91)
To operate this unit using
2001
the default code.
101
(initial setting) To operate Zone 2 or Zone 3 (initial setting)
features (see page 104).
To operate this unit using an
2002
alternative code.
102
To operate Zone 2 orZone 3
features (see page 104).
• You need to set the corresponding remote control AMP lD
(see page 91).
• When using multiple YAMAHA receivers/amplifiers, you
may be able to operate the other components
simultaneously with the default code setting. In this case,
set one of the alternative codes to operate this unit
separately.
Setting remote control tuner codes
Select one of the following codes to set the remote control
tuner code for the component you want to use.
Set AMP/SOURCEfTV to SOURCE and press TUNER
on the remote control to select TUNER as the input source
and then change the remote control code settings.
Tuner
Remote
control
library code
tuner 10
(remote
Function
control
(this unit's
setting)
setting:
see page 91)
2602 To operate this unit using
101
(initial setting) the default code. (initial setting)
2603
To operate this unit using an
102
alternative code.
• You need to set the corresponding remote control tuner ID
(see page 91).
• When using multiple YAMAHA receivers/amplifiers, you
may be able to operate the other components
simultaneously with the default code setting. In this case,
set one of the alternative codes to operate this unit
separately.
REMOTE CONTROL FEATURES
Setting remote control XM codes
Select one of the following codes to set the remote control
XM code for the component you want to use.
Set AMP/SOURCEfTV to SOURCE and press XM on the
remote control to select XM as the input source and then
change the remote control code settings.
XM library
Remote
code
control XM
(remote
Function
10
control
(this unit's
setting)
setting:
see page 91)
2604
To operate this unit using
IOJ
(initial setting) the default code. (initial setting)
2605
To operate this unit using an
102
alternative code.
• You need to set the corresponding remote control XM ID
(see page 91).
• When using multiple YAMAHA receivers/amplifiers, you
may be able to operate the other components
simultaneously with the default code setting. In this case,
set one of the alternative codes to operate this unit
separately.
5
Press ENTER.
The four-digit code set for the selected component
appears in the display window.
0000 appears in the display window if no code has been set.
6
Press the numeric buttons to enter the
four-digit remote control code for the
component you want to use.
For a complete list of available remote control codes,
refer to "LIST OF REMOTE CONTROL CODES" at
the end of this manual.
58
MUSIC ENTERTAIN
0
®"'0
ECT
c!f
CD 0
@)PEA"@V
7
Press ENTER to set the number.
OK appears in the display window if setting was
successful.
NG appears in the display window if the setting was
unsuccessful. In this case, start over from step 3.
If you continuously want to set up another code for another
component, press the input selector button or
SELECT
11 /
' V
to select the component, then repeat steps 4
through 6.
95
Setting remote control AMP codes
Select one of the following codes to set the remote control
AMP code for the component you want to use.
Set AMP/SOURCEfTV to AMP or SOURCE and then
change the remote control code settings.
AMP library
Remote
control
code
AMP 10
(remote
Function
control
(this unit's
setting)
setting:
see page 91)
To operate this unit using
2001
the default code.
101
(initial setting) To operate Zone 2 or Zone 3 (initial setting)
features (see page 104).
To operate this unit using an
2002
alternative code.
102
To operate Zone 2 orZone 3
features (see page 104).
• You need to set the corresponding remote control AMP lD
(see page 91).
• When using multiple YAMAHA receivers/amplifiers, you
may be able to operate the other components
simultaneously with the default code setting. In this case,
set one of the alternative codes to operate this unit
separately.
Setting remote control tuner codes
Select one of the following codes to set the remote control
tuner code for the component you want to use.
Set AMP/SOURCEfTV to SOURCE and press TUNER
on the remote control to select TUNER as the input source
and then change the remote control code settings.
Tuner
Remote
control
library code
tuner 10
(remote
Function
control
(this unit's
setting)
setting:
see page 91)
2602 To operate this unit using
101
(initial setting) the default code. (initial setting)
2603
To operate this unit using an
102
alternative code.
• You need to set the corresponding remote control tuner ID
(see page 91).
• When using multiple YAMAHA receivers/amplifiers, you
may be able to operate the other components
simultaneously with the default code setting. In this case,
set one of the alternative codes to operate this unit
separately.
REMOTE CONTROL FEATURES
Setting remote control XM codes
Select one of the following codes to set the remote control
XM code for the component you want to use.
Set AMP/SOURCEfTV to SOURCE and press XM on the
remote control to select XM as the input source and then
change the remote control code settings.
XM library
Remote
code
control XM
(remote
Function
10
control
(this unit's
setting)
setting:
see page 91)
2604
To operate this unit using
IOJ
(initial setting) the default code. (initial setting)
2605
To operate this unit using an
102
alternative code.
• You need to set the corresponding remote control XM ID
(see page 91).
• When using multiple YAMAHA receivers/amplifiers, you
may be able to operate the other components
simultaneously with the default code setting. In this case,
set one of the alternative codes to operate this unit
separately.
5
Press ENTER.
The four-digit code set for the selected component
appears in the display window.
0000 appears in the display window if no code has been set.
6
Press the numeric buttons to enter the
four-digit remote control code for the
component you want to use.
For a complete list of available remote control codes,
refer to "LIST OF REMOTE CONTROL CODES" at
the end of this manual.
58
MUSIC ENTERTAIN
0
®"'0
ECT
c!f
CD 0
@)PEA"@V
7
Press ENTER to set the number.
OK appears in the display window if setting was
successful.
NG appears in the display window if the setting was
unsuccessful. In this case, start over from step 3.
If you continuously want to set up another code for another
component, press the input selector button or
SELECT
11 /
' V
to select the component, then repeat steps 4
through 6.
95