Yamaha RX-V1600 Owner's Manual page 95

• Remote sensor PEt'10TE
SEt·~
Use to activate or deactivate the signal-receiving
capability of the remote control sensor on the front panel
of this unit.
Choices: ON, OFF
• Select ON if you want to activate the signal-receiving
capability of the remote control sensor.
• Select OFF if you want to deactivate the signal-
receiving capability of the remote control sensor.
We recommend setting this parameter to ON in most cases.
• Wake on RS-232C access I.dRI<E
m·~
232C
Use to set this unit to transmit data via the RS-232C
interface when this unit is in the standby mode.
Choices: Y (yes), N (no)
• Select Y set this unit to transmit data via the RS-232C
interface.
• Select N set this unit not to transmit data via the
RS-232C interface.
• Remote control AMP 10 PEt'10TE Rt'1P
Use to set the AMP ID of this unit for remote control
recognition (see page 95).
Choices: 101, ID2
• Select ID 1 when the remote control AMP library code
is set to 2001.
• Select ID2 when the remote control AMP library code
is set to 2002.
You need to set the corresponding remote control code for the
remote control.
• Remote control tuner 10
~~Et'1OTE TUt·~
Use to set the tuner ID of this unit for remote control
recognition (see page 95).
Choices: 101, ID2
• Select ID1 when the remote control tuner library code
is set to 2602.
• Select ID2 when the remote control tuner library code
is set to 2603.
You need to set the corresponding remote control code for the
remote control.
ADVANCED SETUP
• Remote control XM 10
~:Et'10TE
>=:1' 1
(U.S.A. model only)
Use to switch the XM-related remote control codes
between IDI and ID2.
Choices: 101, ID2
• Select ID 1 when the remote control XM library code is
set to 2604.
• Select ID2 when the remote control XM library code is
set to 2605.
You need to set the corresponding remote control code for the
remote control.
• Fan operation mode F!=lH 1'10DE
Use to set the operation of the cooling fan of this unit.
Choices: AUTO, CONT.
• Select AUTO to set the fan to operate automatically
according to the temperature of this unit.
• Select CONT. to set the fan to operate continuously
regardless of the temperature of this unit.
• Tuner frequency step TU
(Asia and General models only)
Use to set the tuner frequency step according to the
frequency spacing in your area.
Choices: AMlOIFMlOO, AM9/FM50
• Select AM 1
OIFM
100 for North, Central and South
America.
• Select AM9IFM50 for aU other areas.
• Bi-AMP BI-Rt'1P
Use to activate or deactivate the bi-AMP function.
Choices: ON, OFF
• Select ON if you want to activate the bi-AMP function.
• Select OFF if you want to deactivate the bi-AMP
function.
When BI-AMP is set to ON, the SURROUND BACK terminals
cannot be used to connect surround back speakers in that the
SURROUND BACK terminals are already used for the bi-AMP
connection (see page 19).
• Video reset i')-F£SET
Use to initialize the parameter settings for DISPLAY SET
in OPTION MENU (see page 85). This feature is useful if
the SET MENU items are not displayed on your video
monitor due to a technical error between the CMPNT lIP
setting and the capability of your video monitor. That is, if
your video monitor does not support the analog video
signals with 480p of resolution, the SET MENU items
may not be displayed on your video monitor when
CMPNT lIP is set to ON (see page 85).
Choices: YES, CANCEL
The parameter setting for DIMMER is not initialized (see
page 85).
91
• Remote sensor PEt'10TE
SEt·~
Use to activate or deactivate the signal-receiving
capability of the remote control sensor on the front panel
of this unit.
Choices: ON, OFF
• Select ON if you want to activate the signal-receiving
capability of the remote control sensor.
• Select OFF if you want to deactivate the signal-
receiving capability of the remote control sensor.
We recommend setting this parameter to ON in most cases.
• Wake on RS-232C access I.dRI<E
m·~
232C
Use to set this unit to transmit data via the RS-232C
interface when this unit is in the standby mode.
Choices: Y (yes), N (no)
• Select Y set this unit to transmit data via the RS-232C
interface.
• Select N set this unit not to transmit data via the
RS-232C interface.
• Remote control AMP 10 PEt'10TE Rt'1P
Use to set the AMP ID of this unit for remote control
recognition (see page 95).
Choices: 101, ID2
• Select ID 1 when the remote control AMP library code
is set to 2001.
• Select ID2 when the remote control AMP library code
is set to 2002.
You need to set the corresponding remote control code for the
remote control.
• Remote control tuner 10
~~Et'1OTE TUt·~
Use to set the tuner ID of this unit for remote control
recognition (see page 95).
Choices: 101, ID2
• Select ID1 when the remote control tuner library code
is set to 2602.
• Select ID2 when the remote control tuner library code
is set to 2603.
You need to set the corresponding remote control code for the
remote control.
ADVANCED SETUP
• Remote control XM 10
~:Et'10TE
>=:1' 1
(U.S.A. model only)
Use to switch the XM-related remote control codes
between IDI and ID2.
Choices: 101, ID2
• Select ID 1 when the remote control XM library code is
set to 2604.
• Select ID2 when the remote control XM library code is
set to 2605.
You need to set the corresponding remote control code for the
remote control.
• Fan operation mode F!=lH 1'10DE
Use to set the operation of the cooling fan of this unit.
Choices: AUTO, CONT.
• Select AUTO to set the fan to operate automatically
according to the temperature of this unit.
• Select CONT. to set the fan to operate continuously
regardless of the temperature of this unit.
• Tuner frequency step TU
(Asia and General models only)
Use to set the tuner frequency step according to the
frequency spacing in your area.
Choices: AMlOIFMlOO, AM9/FM50
• Select AM 1
OIFM
100 for North, Central and South
America.
• Select AM9IFM50 for aU other areas.
• Bi-AMP BI-Rt'1P
Use to activate or deactivate the bi-AMP function.
Choices: ON, OFF
• Select ON if you want to activate the bi-AMP function.
• Select OFF if you want to deactivate the bi-AMP
function.
When BI-AMP is set to ON, the SURROUND BACK terminals
cannot be used to connect surround back speakers in that the
SURROUND BACK terminals are already used for the bi-AMP
connection (see page 19).
• Video reset i')-F£SET
Use to initialize the parameter settings for DISPLAY SET
in OPTION MENU (see page 85). This feature is useful if
the SET MENU items are not displayed on your video
monitor due to a technical error between the CMPNT lIP
setting and the capability of your video monitor. That is, if
your video monitor does not support the analog video
signals with 480p of resolution, the SET MENU items
may not be displayed on your video monitor when
CMPNT lIP is set to ON (see page 85).
Choices: YES, CANCEL
The parameter setting for DIMMER is not initialized (see
page 85).
91