Yamaha RX-V1600 Owner's Manual page 116

TROUBLESHOOTING
Problem Cause
Remedy
See
page
Dolby Digital or DTS
The connected component is not set to Make an appropriate setting following the operations
sources cannot
be output Dolby Digital or DTS digital instructions for your component.
-
played. (Dolby Digital signals.
or DTS indicator in
the front panel
The input mode is set to ANALOG. Set the input mode to AUTO or COAX/OPT.
display does not light
43
up.)
A humming sound Incorrect cable connections. Firmly connect the audio plugs. If the problem
can be heard. persist", the cables may be defective.
-
No connection from the turntable to the Connect the grounding cord of your turnable to the
27
GND terminal. GND terminal of this unit.
The volume level is The record is being played on a turntable The turntable should be connected to this unit through
low while playing a
with an MC cartridge. an MC-head amplifier.
27
record.
The volume level The component connected to the OUT Turn on the power to the component.
cannot
be
increased, (REC) jacks of this unit is turned off.
-
or the sound is
distorted.
The sound effect It is not possible to record the sound effect
------------
---
cannot be recorded. with a recording component.
----
------
A source cannot be The source component is not connected to Connect the source component to the DIGITAL
20-27
recorded by a digital this unit's DIGITAL INPUT jacks. INPUT jacks.
recording component
Some components cannot record the
~
connected to this
DIGITAL OUTPUT
Dolby Digital or DTS sources.
jack.
r----_
A source cannot
be The source component is not connected to Connect the source component to the analog AUDIO
recorded by an
the analog AUDIO IN jacks of this unit. IN jacks.
analog component 20--27
connected to the
AUDIO OUT jacks.
The sound field MEMORY GUARD is set to ON. Select OFF.
parameters and some
other settings on this 86
unit cannot be
changed.
This unit does not The internal microcomputer has been Disconnect the AC power cable from the outlet and
operate properly.
frozen by an external electric shock (such then plug it in again after about
30
seconds.
-
as lightning or excessive static electricity)
or by a power supply with low voltage.
CHECK SP WIRES
Speaker cables are short circuited. Make sure all speaker cables are connected correctly.
appears in the front
15
panel display.
There is noise
This unit is too close to the digital or Move this unit further away from such equipment.
interference from radio-frequency equipment.
digital or radio-
-
frequency equipment,
or this unit.
The picture is The video source uses scrambled or
----------.
disturbed. encoded signals to prevent dubbing.
----
This unit suddenly
The internal temperature becomes too Wait for about I hour until this unit cools down and
enters the standby
high and the overheat protection circuitry then turn it back on. -
mode.
has been activated.
112
TROUBLESHOOTING
Problem Cause
Remedy
See
page
Dolby Digital or DTS
The connected component is not set to Make an appropriate setting following the operations
sources cannot
be output Dolby Digital or DTS digital instructions for your component.
-
played. (Dolby Digital signals.
or DTS indicator in
the front panel
The input mode is set to ANALOG. Set the input mode to AUTO or COAX/OPT.
display does not light
43
up.)
A humming sound Incorrect cable connections. Firmly connect the audio plugs. If the problem
can be heard. persist", the cables may be defective.
-
No connection from the turntable to the Connect the grounding cord of your turnable to the
27
GND terminal. GND terminal of this unit.
The volume level is The record is being played on a turntable The turntable should be connected to this unit through
low while playing a
with an MC cartridge. an MC-head amplifier.
27
record.
The volume level The component connected to the OUT Turn on the power to the component.
cannot
be
increased, (REC) jacks of this unit is turned off.
-
or the sound is
distorted.
The sound effect It is not possible to record the sound effect
------------
---
cannot be recorded. with a recording component.
----
------
A source cannot be The source component is not connected to Connect the source component to the DIGITAL
20-27
recorded by a digital this unit's DIGITAL INPUT jacks. INPUT jacks.
recording component
Some components cannot record the
~
connected to this
DIGITAL OUTPUT
Dolby Digital or DTS sources.
jack.
r----_
A source cannot
be The source component is not connected to Connect the source component to the analog AUDIO
recorded by an
the analog AUDIO IN jacks of this unit. IN jacks.
analog component 20--27
connected to the
AUDIO OUT jacks.
The sound field MEMORY GUARD is set to ON. Select OFF.
parameters and some
other settings on this 86
unit cannot be
changed.
This unit does not The internal microcomputer has been Disconnect the AC power cable from the outlet and
operate properly.
frozen by an external electric shock (such then plug it in again after about
30
seconds.
-
as lightning or excessive static electricity)
or by a power supply with low voltage.
CHECK SP WIRES
Speaker cables are short circuited. Make sure all speaker cables are connected correctly.
appears in the front
15
panel display.
There is noise
This unit is too close to the digital or Move this unit further away from such equipment.
interference from radio-frequency equipment.
digital or radio-
-
frequency equipment,
or this unit.
The picture is The video source uses scrambled or
----------.
disturbed. encoded signals to prevent dubbing.
----
This unit suddenly
The internal temperature becomes too Wait for about I hour until this unit cools down and
enters the standby
high and the overheat protection circuitry then turn it back on. -
mode.
has been activated.
112