Yamaha RX-V1600 Owner's Manual page 35

3
Press MAIN ZONE ON/OFF
J
ZONE 2 ON/OFF
or ZONE 3 ON/OFF on the front panel (or
POWER on the remote control) to turn on this
unit, Zone 2 or Zone 3.
CONNECTIONS
Follow the procedure below to change the impedance
setting for all speakers.
CAUTION
,I,
:til~
• When MASTER ON/OFF is pressed inward to the ON
position, you can also press POWER or STANDBY on the
remote control to turn on or set this unit, Zone 2 and Zone
3 to the standby mode simultaneously.
• For details about controlling Zone 2 and Zone 3 using the
remote control, see page 106.
NQtij~
MAIN ZONE ON/OFF, ZONE 2 ON/OFF and ZONE 3
ON/OFF on the front panel as well as POWER and
STANDBY on the remote control are operational only when
MASTER ON/OFF is pressed inward to the ON position.
Front panel
or
Remote control
If you are using 6 ohm speakers, set the impedance to
6 ohms before using this unit.
1
Press MASTER ON/OFF on the front panel to
release it outward to the OFF position to set
this unit, Zone 2 and Zone 3 to the standby
mode.
MASTER
ON~
2
Press and hold STRAIGHT (EFFECT) on the
front panel and then press MASTER ON/OFF
inward to the ON position to turn on the
power of th is unit.
SP IMP.-8nMIN appears in the front panel display.
4
Press MASTER ON/OFF on the front panel
again to release it outward to the OFF
position to turn off this unit.
This unit, Zone 2 and Zone 3 are turned off.
ST~
t
MASTER
ON~
MASTER
ON~
3
HDI..JH~·iCE[)
SETUP
SF' I t'1P
ft
-BOt'1 I t·~
Press STRAIGHT (EFFECT) on the front
panel repeatedly to select the impedance of
your speakers.
STRAIGHT
~
• Select 6 ohms if you are using 6 ohm speakers.
4
Press MASTER ON/OFF on the front panel to
release it outward to the OFF position to save
the new setting and set this unit, Zone 2 and
Zone 3 to the standby mode.
This unit will be set to the standby mode.
MASTER
ON~
You can also set the speaker impedance by using the SP
IMP. parameter in the ADVANCED SETUP menu (see
page 90).
31
3
Press MAIN ZONE ON/OFF
J
ZONE 2 ON/OFF
or ZONE 3 ON/OFF on the front panel (or
POWER on the remote control) to turn on this
unit, Zone 2 or Zone 3.
CONNECTIONS
Follow the procedure below to change the impedance
setting for all speakers.
CAUTION
,I,
:til~
• When MASTER ON/OFF is pressed inward to the ON
position, you can also press POWER or STANDBY on the
remote control to turn on or set this unit, Zone 2 and Zone
3 to the standby mode simultaneously.
• For details about controlling Zone 2 and Zone 3 using the
remote control, see page 106.
NQtij~
MAIN ZONE ON/OFF, ZONE 2 ON/OFF and ZONE 3
ON/OFF on the front panel as well as POWER and
STANDBY on the remote control are operational only when
MASTER ON/OFF is pressed inward to the ON position.
Front panel
or
Remote control
If you are using 6 ohm speakers, set the impedance to
6 ohms before using this unit.
1
Press MASTER ON/OFF on the front panel to
release it outward to the OFF position to set
this unit, Zone 2 and Zone 3 to the standby
mode.
MASTER
ON~
2
Press and hold STRAIGHT (EFFECT) on the
front panel and then press MASTER ON/OFF
inward to the ON position to turn on the
power of th is unit.
SP IMP.-8nMIN appears in the front panel display.
4
Press MASTER ON/OFF on the front panel
again to release it outward to the OFF
position to turn off this unit.
This unit, Zone 2 and Zone 3 are turned off.
ST~
t
MASTER
ON~
MASTER
ON~
3
HDI..JH~·iCE[)
SETUP
SF' I t'1P
ft
-BOt'1 I t·~
Press STRAIGHT (EFFECT) on the front
panel repeatedly to select the impedance of
your speakers.
STRAIGHT
~
• Select 6 ohms if you are using 6 ohm speakers.
4
Press MASTER ON/OFF on the front panel to
release it outward to the OFF position to save
the new setting and set this unit, Zone 2 and
Zone 3 to the standby mode.
This unit will be set to the standby mode.
MASTER
ON~
You can also set the speaker impedance by using the SP
IMP. parameter in the ADVANCED SETUP menu (see
page 90).
31