Tool-Chg Command; Enabling Pen Change Commands; [Vs Command] Vs Command (Velocity Select); Feed The Loaded Sheet [Fs Command] Fs Command (Force Select) - Roland Camm-1 PNC-1850 User Manual

• Giving priority to settings from the computer

TOOL-CHG COMMAND

Display readout
TOOL-CHG COMMAND
<IGNORE> EFFECT
Factory default setting
IGNORE
Available settings
IGNORE / EFFECT
Procedure
At the top menu, press the
of the lower line of the display, press
Use or to move the blinking cursor to "TOOL-CHG" on the right side of the upper line of the display, and press
ENTER again. Change the value with
* See "2-5 PLOTTING ON PAPER MEDIA" on page 32 for a description of operation when a pen change command is received.
When "EFFECT" is selected and a tool select command is sent from the computer, the following message will be displayed,
and all operation will halt.
When this message is displayed and the tool must be changed, open the front cover, and
insert the appropriate tool into the tool carriage and close the front cover. Press
plotting will restart.
If tool change is not required, press
If the tool select command from the computer specifies the tool number, select the tool number from the top menu.
VS COMMAND
Display readout
VS COMMAND
<IGNORE> EFFECT
Factory default setting
IGNORE
Available settings
IGNORE / EFFECT
FS COMMAND
Display readout
FS COMMAND
<IGNORE> EFFECT
Factory default setting
IGNORE
Available settings
IGNORE / EFFECT
30
Enabling tool change commands
Explanation
This sets the handling of tool select (SP instruction). When cutting is executed,
normally set this to "IGNORE".
When a tool select command (SP command) is sent from the computer, it will be
ignored if this is set to "IGNORE". If set to "EFFECT", SP change commands will
be received. If tool changes are needed set this to "EFFECT".
When plotting with pen and paper, set to "EFFECT" if pen change is needed (or if
data includes pen change commands). Select the top menu tool number (number at
left of top line on display) and software (or driver) pen number to match the pen to
be used.
For plot data without pen changes, or if pen change data is present but you will
ignore it, set "IGNORE". In this case, before sending the data from the computer
select the tool number from the top menu with the correct plotting parameters (or
set a tool number if there isn't one).
Refer to page 32 "2-5 PLOTTING ON PAPER MEDIA" for additional information
on plotting.
key once. Press or
MENU
, then press
MENU
ENTER
or and press
ENTER when the message is displayed and plotting will restart.
VS command (Velocity Select)
Explanation
To perform cutting at the speed determined by a VS command (tool speed setting
command) sent from the computer, set this to "EFFECT." When set to "IG-
NORE," cutting is performed using the values for " ** cm/s" and "UPSPEED"
set at the top menu.
Procedure
At the top menu, press the
blinking cursor to "SUBMENU" on the right side of the lower line of the display,
press , then press
ENTER
Use or
lower line of the display, and press
and press
ENTER
FS command (Force Select)
Explanation
To perform cutting at the tool force determined by an FS command (tool force
setting command) sent from the computer, set this to "EFFECT." When set to
"IGNORE," cutting is performed using the value for "** gf" set at the top menu.
Procedure
At the top menu, press the
blinking cursor to "SUBMENU" on the right side of the lower line of the display,
press , then press
ENTER
Use or
the lower line of the display, and press
or and press
to move the blinking cursor to "SUBMENU" on the right side
again.
to save the new setting.
ENTER
ENTER and
key once. Press
MENU
MENU again.
to move the blinking cursor to "VS-CMND" on the left side of the
again. Change the value with
ENTER
to save the setting.
key once. Press
MENU
again.
MENU
to move the blinking cursor to "FS-CMND" on the right side of
ENTER again. Change the value with
to save the new setting.
ENTER
TOOL-CHG:TOOLNO2
or to move the
or
or to move the