Table of Contents
Advertisement
@2 Digital Output key (DIGITAL OUT)
This key, in combination with the Numeric keys, is used
to select a logical output number and produce a one
shot pulse for activating an assigned event.
Pressing this key while holding down the SHIFT key will
turn on the housing defroster of the camera (DEF ON).
@3 Log-out key (LOGOUT)
This key, in combination with the CAMERA (ENTER)
key, is used to log out from the system.
To prevent a log-out error, press CAMERA (ENTER)
while holding down the LOGOUT key.
Pressing this key while holding down the SHIFT key will
turn off the user's auxiliary 1 switch of the Receiver
(AUX1 OFF).
@4 Call Preset key (CALL PRESET)
This key, in combination with the Numeric keys, is used
to move to a preset position of the selected camera in a
system equipped with the specified cameras.
Pressing this key while holding down the SHIFT key will
turn off the user's auxiliary 2 switch of the Receiver
(AUX2 OFF).
@5 Camera Position key (CAM POSI)
This key, in combination with the Numeric keys, is used
to move the camera to the preset position programmed
in advance in a system equipped with the specified
cameras.
Pressing this key while holding down the SHIFT key will
turn off the housing defroster of the camera (DEF OFF).
@6 Camera / Enter key [CAMERA(ENTER)]
CAMERA: This key is used for camera selection. Press
the desired Numeric keys, then press this key to
select the camera.
ENTER: This key, in combination with the Numeric
keys, is used to enter numeric input, such as opera-
tor ID and password.
It is also used to execute the currently highlighted
selection and to enter a submenu of the Camera
Menu.
Pressing CAMERA (ENTER) while holding down the
SHIFT key will activate the auto panning function of the
selected camera (AUTO PAN).
@7 Clear / Escape key [CLEAR (ESC)]
Clear: This key is used to clear numeric input from the
LCD Display.
Escape: This key is used to escape from the currently
highlighted selection and return to the previous
page of the Camera Menu.
This key is also used to exit from alarm selecting mode
to normal operation mode.
49
@8 Numeric keys (0 - 9)
These keys are used for numeric input into the system
such as the camera and monitor number, sequence
number, preset position, etc.
@9 Shift key (SHIFT)
Pressing this key in combination with keys to which
special functions have been assigned will activate
these functions.
#0 Next key (NEXT)
When a Tour Sequence running in forward direction has
been paused with the Pause key, pressing this key will
move the sequence one frame to the next step (in for-
ward run direction). If the sequence was running in
reverse direction, the key will move the sequence one
frame to the next step (in reverse run direction).
The key is also used to select a camera. Pressing it
while holding down the CAMERA (ENTER) key will
replace the currently selected camera with the next
higher camera number, if the active monitor is in Spot
mode.
Similarly pressing this key while holding down the
MONITOR key will select the next higher monitor num-
ber.
When selecting alarms, pressing this key while holding
down the ALARM key will select the next alarm.
Pressing this key while holding down the SHIFT key will
display the software version of the system on the LCD
Display of the controller.
#1 Previous key (PREV)
When a Tour Sequence running in forward direction has
been paused with the Pause key, pressing this key will
move the sequence one frame to the previous step (in
forward run direction). If the sequence was running in
reverse direction, the key will move the sequence one
frame to the previous step (in reverse run direction).
The key is also used to select a camera. Pressing it
while holding down the CAMERA (ENTER) key will
replace the currently selected camera with the next
lower camera number, if the active monitor is in Spot
mode.
Similarly pressing this key while holding down the
MONITOR key will select the next lower monitor num-
ber.
When selecting alarms, pressing this key while holding
down the ALARM key will select the previous alarm.
Pressing this key while holding down the SHIFT key will
display the controller ID on the LCD display (S-CTL ID).
#2 Stop key (STOP)
This key is used to end a Tour Sequence that is being
run on the active monitor.
To end a Group sequence, select one of the monitors
that are being run on the sequence, then press this key.
#3 Pause key (PAUSE)
This key is used to pause a Tour or Group Sequence
that is being run on the active monitor.
Advertisement
Table of Contents
