Through The Ceiling; Existing Flue System; Outside Air; Mobile Home Installation - England's Stove Works 25-PDV Installation & Operation Manual

Hide thumbs Also See for 25-PDV:

Installation and operation manual (26 pages)

Table Of Contents

Table of Contents

Available languages

When venting the stove through the ceiling, the pipe is connected the same as through the wall,

except the clean out tee is always on the inside of the house, and a 3" adapter is added before the

clean-out tee. You must use the proper ceiling support flanges and roof flashing supplied by the pipe

manufacturer -- follow the pipe manufacturer's directions and Illustration 1 in this manual. It is

important to note that if your vertical runs of pipe are more than fifteen feet (15'), the pellet vent pipe

should be increased to four inches (4") in diameter. Do not exceed four feet (4') of pipe on a horizontal

run, and do attempt to use the least number of elbows in the flue system. If an offset is used it is

better to install a 45-degree elbow whenever possible. Please remember, installing elbows may

inhibit your draft by up to 15% per elbow.

If you are replacing a wood stove with a pellet unit the chimney or pipe should be thoroughly

cleaned before proceeding with the installation. If connecting this stove to a factory built chimney, it

may ONLY be a 6" flue, UL103 HT venting system (ULC S629 if Canada). Connection to any other

factory built chimney may result in a poorly operating or dangerous stove installation.

connecting to an existing masonry chimney, the cross-sectional area of the flue must be considered.

A chimney with a flue larger than 6" round (28.27 sq. in.) may require relining with an approved pellet

stove chimney lining system. Make sure the chimney meets the minimum standards listed in NFPA

211 (A chimney professional can confirm this upon inspection).

Outside air is mandatory for this unit to operate properly. This unit has been designed and tested

with this connection, because so many homes are airtight and there is not adequate combustion air

available inside the dwelling. The air intake pipe is located on the bottom side of the burn pot (from

the rear) and measures 1 ½" inside diameter (I.D.). The connection can be made with a metal 1

I.D. coupler and pipe (see "Important Information" section of manual), and should exit through the

wall. Be sure to secure the pipe to the unit with a clamp or aluminum tape. The outside end of the

pipe should be covered (screened) to prevent foreign matter from entering the system. Our Outside

Air Kit (Part Number PU-OAK) can be used. If the unit is located below ground level, you will need to

run the pipe up and then outside the dwelling. NOTE: If the total run of the connection exceeds 6', if

more than 2 elbows are used, or if a basement installation, use 3" metal pipe (and coupler) instead.

Note: If an older unit, measure the opening to determine what size pipe to use or couple to.

Secure the heater to the floor using the two holes in the pedestal. If the unit is on a combustible

surface, you will need to drill matching holes in the floor protection that you choose (see Floor

Protection section). Do not disturb the structural integrity of the home, and be sure the unit is

permanently electrically grounded to the chassis of your home. Remember that outside combustion

air is mandatory, and not to install the unit in a sleeping room of the home.

CAUTION: THE STRUCTURAL INTEGRITY OF THE MANUFACTURED HOME FLOOR, WALL AND

*IMPROPER INSTALLATION: The manufacturer will not be held responsible for damage caused by

the malfunction of a stove due to improper venting or installation.

Call 800-245-6489 and/or consult a professional installer if you have any questions.

IMPORTANT: Improper hook-up (too much pipe, too many elbows, etc.) will cause the unit not to

operate. Call Technical Support (800-245-6489) if you have questions about your hook-up or if

your unit will not operate.

IMPORTANT! READ AND FOLLOW ALL INSTALLATION AND MAINTENANCE INSTRUCTIONS, INCLUDING

CLEANING THE UNIT AS SPECIFIED, AND REPLACING GASKETS ANNUALLY, AND PARTS AS NEEDED.

ENGLAND'S STOVE WORKS IS NOT RESPONSIBLE FOR ANY DAMAGE OR INJURY INCURRED DUE TO NEGLECT, OR

DUE TO UNSAFE INSTALLATION OR USAGE OF THIS PRODUCT. CALL TECHNICAL SUPPORT WITH QUESTIONS.