Kyocera FS-1750 User Manual page 5

Shielded circular cable should be used for interfacing with the computer. Caution to user Any modification without prior permission may cause harmful
interference. If any modification/change is introduced to this equipment without prior permission, Kyocera as the manufacturer cannot guarantee compliance
The printer may be optionally installed with the following units: Conforming to the Class A limits Ì HS-3E Bulk Paper Stacker (for FS-3750) Ì PF-7E Bulk
Paper Feeder Conforming to the Class B limits Ì Ì Ì Ì Ì Ì Ì Ì Ì EF-1 Envelope Feeder DU-20 Duplexer (for FS-3750) DU-21 Duplexer (for FS-1750/FS-3750)
HS-20 Paper Handler/Stacker (for FS-3750) HS-21 Paper Handler/Stacker (for FS-1750/FS-3750) PF-20/PF-20mini Paper Feeder (for FS-3750)
PF-21/PF-21mini Paper Feeder (for FS-1750/FS-3750) SO-6 Sorter/Stacker ST-20 Bulk Paper Stacker iv Introduction Interface connectors Important note
on the interface connectors Be sure to turn off printer power before connecting or disconnecting an interface cable to the printer. For protection against static
discharge which may be applied to the printer's internal electronics through the interface connector(s), keep any interface connector which is not in use
capped using the protective cap supplied. Use shielded interface cable. Safety information Laser safety This printer is certified as a Class 1 laser product
Department of Health and Human Services (DHHS) Radiation Performance Standard according to Radiation Control for Health and Safety Act of 1968. This
means that the printer does not produce hazardous laser radiation. Since radiation emitted inside the printer is completely confined within protective housings
and external covers, the laser beam cannot escape from the printer during any phase of user operation. Laser notice This printer is certified in the U.S. to
conform to the requirements of DHHS 21 CFR Subchapter for Class I (1) laser products, and elsewhere is certified as a Class I laser product conforming to
the requirements of IEC 825-1. Caution Laser radiation when open. DO NOT STARE INTO BEAM OR VIEW DIRECTLY WITH OPTICAL INSTRUMENTS.
Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. The labels shown
Similar labels are affixed to same location on the FS-1750. (Philippines) (European/ Asian countries) (U.S.A./Canada) v Introduction CDRH regulations The
Center of Devices and Radiological Health (CDRH) of the U.S. Food and Drug Administration implemented regulations for laser products on August 2, 1976.
These regulations apply to laser products manufactured after August 1, 1976. Compliance is mandatory for products marketed in the United States. A label
indicating compliance with the CDRH regulations must be attached to laser products marketed in the United States.
Ozone concentration The printers generate ozone gas (O3) which may concentrate in the place of installation and cause an unpleasant smell. To minimize
concentration of ozone gas to less than 0.1 ppm, we recommend you not to install the printer in a confined area where ventilation is blocked. IMPORTANT
2. Unplug this product from the wall outlet before cleaning. 3. Do not use this product near water. 4.
Do not place this product on an unstable cart, stand, or table. The product may fall, causing serious damage to the product. 5. Slots and openings in the
cabinet and the back are provided for ventilation to ensure reliable operation of the product and to protect it from overheating, these openings must not be
blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should never be
with FCC rules. To use equipment which does not comply with FCC rules is prohibited.
SAFEGUARDS 1. Read all of these instructions and save these instructions for later use.
placed near or over a radiator or heat register.
You're reading an excerpt. Click here to read official KYOCERA
FS-1750 user guide
http://somemanuals.com/dref/324820
under the U.S.
are affixed to the FS-3750.