Kyocera FS-1750 User Manual page 21

The messageý3ULQWý&DQFHO" will appear in the message display and the interface to be canceled will be displayed.
3DUDOOHO 6HULDO 2SWLRQý (appears only when an optional interface is installed) 6. Selecting the interface to cancel using the + or key and then
press the ENTER key. Printing from the interface selected will be stopped. A few pages may be printed even after the CANCEL key is pressed as remaining
data received before the CANCEL key was pressed is printed. The messageý3ULQWý&DQFHO"ý&XUUHQWýMRE will also be displayed when the
CANCEL key is pressed for the purpose of stopping the printing of status pages or font lists from the control panel. When the ENTER key is pressed, the
messageý&DQFHOOLQJýGDWD appears in the message display and printing stops after the printer finishes printing the current page. Press the CANCEL
key again if you wish to stop the cancellation of printing. Press the ON LINE key to put the printer back online to continue with other print jobs. Canceling
data from the computer using the CANCEL key will restore temporary settings to their default values. (The same status resulting from executing the
) It is impossible to cancel printing of just one side when printing in duplex mode using an optional duplexer (DU-21). 2-7 2.2. Operating Procedures Status
Printout If you want to check the printer's current status, including memory available, and option settings, you can find the information you need on the status
Proceed as follows: 1. Make sure the message display indicatesý5HDG\. 2. Press the STATUS key. The printer prints a page of status information.
The message display indicatesý 3URFHVVLQJ during printing of the status page, then returns toý 5HDG\. For a full description of the status page, see next
page. Items and values on the status page may vary depending on the printer model and printer's firmware version. 2-8 2.2. Operating Procedures Sample
Status Page 1 2 4 3 5 6 7 8 9 2-9 2.2. Operating Procedures 1 -- Software version This information shows the software version and date of issue of the printer.
2 -- Hardware information This information shows the currently selected paper feed source (indicated by an asterisk), paper size, and main settings of the
printer. 3 -- Page information This information shows the currently selected resolution and number of copies.
4 -- Memory usage This information shows the amount of total memory installed in the printer and the amount of currently available memory. 5 -- Installation
Options This shows the options currently installed in the printer. 6 -- Emulation This shows all available emulations and the currently selected emulation
(marked with an asterisk). The printer is shipped from the factory set to PCL 6 emulation. 7 -- Interface information This information shows all interfaces
installed in the printer and the currently selected interface. 8 -- Fonts at startup (for each interface) This shows the font automatically selected when the
printer starts up (default font). It is possible to set different fonts for the parallel interface and the serial interface. The figure on page 2-9 shows default
settings. The font is set to Courier font (font number: I000). This also shows font information similar to the column below if an optional interface is installed.
9 -- KIR test pattern This is used when setting the printer's KIR mode. For details, see page 2-24. Form Feed Depending on the software, the
messageý:DLWLQJ may be displayed in the message display when you get to the end of a print job. This occurs when the software does not issue a final form
feed to the printer indicating the end of the print data. If you wait awhile,ý)RUP)HHGý7LPH2XW will be displayed and the last page will be printed
Pressing the FORM FEED key allows you to finish printing immediately. 1. Check if the message display readsý:DLWLQJ.
PRESCRIBE 2e RES command.
page. To print out a status page, the printer must be on-line.
You're reading an excerpt. Click here to read official KYOCERA
FS-1750 user guide
http://somemanuals.com/dref/324820
automatically.