Kyocera FS-1750 User Manual page 35

6. to format the card. This message appears when the printer is in the ready state and the battery in the memory card is low. You can still enter the memory
card mode, but the battery should be changed as soon as possible. This message appears when the printer is in the ready state and the battery in the memory
card is dead, or there is no battery at all. It is not possible to use the memory card mode until you insert a good battery in the card.
.3'/ (UURU 3UHVV &217,18( 5$0ý ',6.ý HUURUý úú 3UHVVý &217,18( 0(025[ &$5' HUU ,QVHUW DJDLQ ,QVHUW WKH VDPH 0(025[ &$5' )RUPDW
HUURU 0(025[ &$5' :DUQLQJ EDWWHU\ 0(025[ &$5' %DWWHU\ HUURU 0(025[ &$5' 5-10 5.5 Indicators and Messages Message 0(025[&$5' HUUúú
3UHVV &217,18( Corrective Action This message appears when an error occurs during access to the memory card using the PRESCRIBE 2e RWER (ICCD)
command or from the printer's control panel. Look at the error code given in place ofýúú and refer to the corresponding description given below. Note that
error codes ofýíä and above only result when memory card operations are done fromthe control panel. íì: Data or memory card capacity is too large. · This
error code appears if an attempt is made to write more than 32 MB of data to a memory card or if the capacity of the memory card installed in the printer is
more than 32 MB. Decrease the data being written to the memory card to less than 32 MB. Note that only the memory card of 32 MB and less can be used by
· This error code appears when a data name not existing on the memory card is specified. Check the data names on the memory card. íë: The memory card
does not meet specifications. This memory card cannot be used by this printer. Insert a memory card which can be used by this printer.
(See "Memory Card" of Chapter 2.) íê: The memory card is not a JEIDA card. Only a JEIDA Ver. 4.2 memory card can be used by this printer.
íé: The card is an S-RAM or flash card which cannot be used by this printer. íè: There is no battery in the memory card. Replace the battery in the memory
card with a new one. íç: The memory card is write-protected. Cancel the write-protection of the memory card. íæ: The memory card requires formatting.
Format the memory card from the control panel. íä: The capacity of the memory card is insufficient. This error code appears when an attempt is made to
write more data on the memory card than available memory. To halt the writing of data, first stop data transmissions from the computer, and then the
Press the FORM FEED key if the messageý :DLWLQJ will appear in the message display. The message display will return to readingý5HDG\. ìì: The
memory card is full of data items. The number of data items which can be written on the memory card is limited to 127. Pressing the CONTINUE key will
restore the messageý5HDG\ in the message display. ìê: This is a logical error. Try substituting another flash memory card. ìæ: The flash memory card cannot
be written due to insufficient printer memory. Either delete unnecessary macros and/or fonts stored in the printer, or expand the printer's available memory.
Try substituting another flash memory card. (Error codes ìê throughýìå apply only to a flash memory card.) This message is displayed when you attempt to
use the printer's control panel to change the environmental settings on the interface from which data are presently being received. ),7 (image FITting) flashes
to indicate that a loss of raster data occurred when the data was compressed to be fitted within the currently available memory. Flashingý ),7 extinguishes
automatically when the job times out; the printer receives the next data from the host computer; or if you press any key on the printer's control panel.
Try adding more memory in the printer to prevent this error. ,î) RFFXSLHG 3URFHVVLQJ 3$5 ),7 $é 5-11 5.6. Correcting a Paper Jam 5.6.
Correcting a Paper Jam Theý3DSHU MDP message is displayed on the message display when paper becomes stuck in the paper transport system, the paper
printer's CONTINUE key.
ìå: This is a write error.
feed timing is incorrect, or paper fails to feed at all.
You're reading an excerpt. Click here to read official KYOCERA
FS-1750 user guide
http://somemanuals.com/dref/324820
this printer.