Kyocera FS-1750 User Manual page 30

Remove the old toner container as gently as possible. Old Toner Container Keep the toner container as level as possible while removing. Toner Container
Release Lever (Green) 3. Put the old toner container in the plastic bag supplied with the toner kit.
Dispose of the toner container. Plastic Bag The old toner container may be incinerated without the risk of generating harmful gas. Old Toner Container 4.
Take the new toner container from its bag. With the label side down, thoroughly shake the toner container (in the direction of the arrow) ten times or more to
loosen and mix the toner inside. New Toner Container 5. The bottom of the toner container is sealed with a plastic strip. Carefully pull the sealing strip off the
toner container, making sure not to leak any toner. Dispose of the sealing strip. Sealing Strip 4-2 4.
1. Toner Kit Replacement 6. Install the toner container on the developer as shown in the diagram. Be sure to peel off the seal on the toner container before
mounting the toner container on the developer unit. 7. When the toner container is installed correctly on the developer. 8. Push the top of the toner container
unit ("PUSH HERE") until it locks in. Make sure that the toner container is properly locked in the printer. 9.
Close the top cover by pressing the arrowed part in this diagram. It is necessary to clean the inside of the printer after replacing the toner container. If the
toner container is replaced when the messageý 5HSODFH 7RQHUý &OHDQ SULQWHU is displayed, the messageý &OHDQý SULQWHUý 3UHVVý
&217,18( will be displayed after replacement. After cleaning the inside of the printer (See Section 4.2.
Cleaning), the message will disappear when the CONTINUE key is pressed, and the printer will be ready for printing. 4-3 4.1. Toner Kit Replacement Replace
the Waste Toner Bottle When replacing the toner container, the used waste toner bottle in the printer should also be replaced with a new one from the new
Open the printer side cover. Side Cover Old Waste Toner Bottle 2. Remove the waste toner bottle as shown right. Remove the waste toner bottle as gently as
possible so as not to scatter the waste toner inside. Do not let the opening of the waste toner bottle face downward. Old Waste Toner Bottle 3. Cap the waste
toner bottle after removing from the printer. Cap Old Waste Toner Bottle 4. To avoid toner spilling, place the capped waste toner bottle in the plastic bag
1. Toner Kit Replacement 5. Locate the new waste toner bottle in the toner kit, and install in the printer as shown right. Do not cap the new waste toner bottle.
Insert the new waste toner bottle with the bottle tilted slightly towards you as shown in the figure. New Waste Toner Bottle 6. After ensuring that the bottle is
2. Cleaning In addition to the maintenance procedures described on the following pages, the charger wire in the drum unit and paper feed unit should be
cleaned from time to time, or whenever print quality problems occur. To avoid print quality problems, the following printer parts must be cleaned with every
toner container replacement. If the toner container has been replaced when the messageý5HSODFH 7RQHUý &OHDQ SULQWHU was displayed, the
messageý &OHDQ SULQWHU 3UHVVý &217,18( will be displayed after replacement. After cleaning the inside of the printer following the procedure shown
below, press the CONTINUE key; the message will disappear and the printer will be ready for printing.
Main Charger Unit The main charger unit grid should be cleaned when the toner container is changed. Cleaning the Charger Wire 1. Open the printer side
cover. Main Charger Unit Side Cover 2. Pull the cleaning knob (Green) slowly in and out a few times.
supplied before forwarding to proper disposal. Plastic Bag 4-4 4.
correctly installed, close the side cover. 4-5 4.2. Cleaning 4.
This pulls a cleaning pad inside the drum unit along the wire.
You're reading an excerpt. Click here to read official KYOCERA
FS-1750 user guide
http://somemanuals.com/dref/324820
toner kit. 1.