Kyocera FS-1750 User Manual page 12

3. Names of Parts Interior View Toner Container Release Lever (Green) Top Cover Toner Container Side Cover Cleaner Knob (Green) Waste Toner Bottle
Main Charger Unit Rear View Rear Cover Serial Interface (RS-232C/RS-422A) Connector Parallel Interface Connector Option Interface Slot Cover Option
Paper Handler/Stacker Connector* Power Cord Receptacle *: To protect the printer against static discharge, the connector must be covered with the
1-6 1.4. Setting Up and Interfacing 1.4. Setting Up and Interfacing Before you can use the printer for the first time, you must set up the printer by installing
The steps to be followed in setting up are: 1. Open the top cover. 2. Install the toner container. 3. Close the top cover. 4. Install the waste toner bottle. 5.
6. Open the paper stopper on the face-down output tray. 7. Install the face-up output tray (if required). 8. Connect the printer to the computer. 9. Attach the
Install the printer driver. 1-7 1.4. Setting Up and Interfacing 1--Open the top cover 1. Remove the packing tape from the printer.
2. Open the printer top cover all the way. Top Cover 2--Install the toner container 1. Take the toner container from the toner kit. 2. With the label side down,
thoroughly shake the toner container (in the direction of the arrow) ten times or more to loosen and mix the toner inside. Toner Container 3. The bottom of the
toner container is sealed with a sealing strip. Peel off the seal on the toner container and carefully pull off and dispose of the sealing strip. Be sure to peel the
Sealing strip 4. Install the toner container on the developer as show in the diagram. Developer Unit 1-8 1.4. Setting Up and Interfacing 5. When the toner
container is installed correctly on the developer, push the top of the container unit ("PUSH HERE") until it locks in. Top Cover Make sure that the toner
container is properly locked in the printer. 3--Close the top cover Close the top cover by pressing the arrowed part in this diagram. Top Cover 4--Install the
waste toner bottle The waste toner bottle is in the toner kit supplied with the printer. The waste toner bottle must be installed in the printer.
Install the waste toner bottle in the printer as follows. 1. Take the waste toner bottle from the toner kit supplied. Cap Do not cap the waste toner bottle. Waste
4. Setting Up and Interfacing 2. Open the side cover on the left side of the printer. Side Cover 3. Insert the waste toner bottle with the bottle tilted slightly
Waste Toner Bottle 4. Ensuring that it is correctly inserted, close the side cover. 1-10 1.4. Setting Up and Interfacing 5--Adjusting the paper guides in the
cassette and adding paper The paper cassette provided with the printer can accommodate paper sizes from A5 to legal, by adjusting the position of the paper
guides and the paper stopper. Paper sizes that are not standard sizes (custom sizes) but within the size limitations can also be loaded into the cassette. When
loading custom sizes into the cassette, the size must be input into the printer on the control panel. (Refer to 2.7. Setting Custom Sizes) Standard size paper
[ Before adding paper, remove the paper cassette all the way from the printer. [ Read the paper manufacturer's instructions concerning handling of the paper.
1. Remove the paper cassette from the printer, and place it on a flat, stable surface. Paper Cassette 2. Push the bottom plate down until it locks. Bottom Plate
supplied protective cap when not in use.
the printer components and interfacing with the computer.
Adjusting the paper guides in the cassette and adding paper.
power cord. 10. Print a status page.
11. Test the interface with the computer. 12. Set the emulation mode. 13.
seal off the toner container before the toner container is fitted into the developer unit.
towards you as shown in the figure.
settings are indicated as fixed positions in the cassette.
You're reading an excerpt. Click here to read official KYOCERA
FS-1750 user guide
http://somemanuals.com/dref/324820
Toner Bottle 1-9 1.
3.