Kyocera FS-1750 User Manual page 13

Turn the paper size dial so that the size of the paper you are going to use appears in the paper size window. Paper Size Dial When the paper size dial is set to
"Custom" the paper size must be set into the printer on the control panel. See 2-7 Setting Custom Sizes for the setting procedure.
Paper Size Window 4. Adjust the paper guide and paper stopper positions. Move the paper guides while lifting the green latch on the right. Set the triangular
markings on the guides to the size of paper that you are to use as indicated. Triangle Mark Paper Guide 1-11 1.
4. Setting Up and Interfacing Move the paper stopper while pushing on the green button at the back. Set the paper stopper to the size of paper that you are to
use as indicated in the small windows on the floor of the cassette. When using custom size paper, move the paper guides and paper stopper all the way out,
insert the paper, and then adjust the paper guides and paper stopper to suit. Adjust them so that they are in light contact with the paper.
Paper Stopper 5. Tap the edges of the paper to align the sheets neatly. Set the paper in the cassette as shown. The side of paper that faces downward in the
cassette is the one on which printing is done. Do not load paper into the cassette higher than the limitation mark on the right (The cassette should hold
approximately 250 sheets of paper with a 0.1 mm thickness.) When loading the paper, make sure the leading edge of paper is not bent in any way. Limitation
Hold the cassette as shown in the illustration and insert the paper cassette into the printer cassette slot. Push it straight in as far as it will go. If the paper size
dial on the cassette is not set to match the size of paper inserted, a paper jam may result. 1-12 1.4. Setting Up and Interfacing 6--Open the paper stopper on
the face-down output tray Open the paper stopper as shown right. Paper Stopper 7--Install the face-up output tray (if required) This face-up output tray is a
separate option (PT-4) with the FS-1750. If you want the printed pages stacked face-up (in reverse order), mount the face-up output tray as follows.
Depending on the size of the paper you use, mount the paper stopper on the face-up output tray as shown below. Paper Stopper Legal Size A4 Size Letter Size
4. Setting Up and Interfacing 8--Connect the printer to the computer The printer has two computer cable connectors and a slot for installing an option
interface. The one marked " " is for a parallel (Centronics standard) interface. The one marked "IOIOI" is for a serial (RS-232C/ RS-422A) interface. You
may use whichever is convenient for your computer, with the option interface, if you have already have one installed.
All interface connectors can be used simultaneously with different computers. Serial (RS-232C/RS-422A) Interface Connector Parallel Interface Connector
Option Interface Slot Cover Only connect or disconnect cables to the connectors while the printer and computer power are switched off. Parallel interface
Plug one end of the cable into the connector marked Parallel on the printer. Close the clips on both sides to hold it in place. Plug the other end into a parallel
This connector is usually marked PRINTER. See Appendix C for more details about the parallel interface. Printer Cable Clips Rear Panel Serial interface The
serial interface of this printer is set to RS-232C mode before leaving the factory, but can also be set to RS422A mode to suit your operating environment.
Follow the instructions in Appendix C. 9--Attach the power cord 1. Check that the power switch is off. 2. Plug one end of the power cord into the receptacle at
Power Cord Receptacle 1-14 1.4. Setting Up and Interfacing 10--Print a status page Test that the printer works by printing out a status page as follows.
mark 6. Set the stack of paper so that it is under the clips as shown. Clip 7.
Face-up Output Tray 1-13 1.
(Centronics) interface connector on your computer.
the back of the printer. Power Cord 3. Plug the other end into the wall outlet.
You're reading an excerpt. Click here to read official KYOCERA
FS-1750 user guide
http://somemanuals.com/dref/324820