Kyocera FS-1750 User Manual page 17

It begins by explaining how to remove the main circuit board from the printer, and explains how to install a SIMM (single in-line memory module) on the
main circuit board. The FS-1750 comes supplied with 8 MB of memory installed, and likewise the FS-3750 comes with 16 MB of memory supplied. Two slots
are provided for expanding the memory in your printer so that more complex printing can be done, as well as increasing the printing speed. By installing the
optional memory card into your printer, the memory in the FS-1750 can be increased to a maximum of 72 MB, and the FS-3750 can be increased to a
maximum of 64 MB. [ A 16 MB SIMM is installed in one of the SIMM sockets in the FS-3750, so in order to increase the memory to the maximum 64 MB this
SIMM must be changed. [ The expansion memory should be installed only by a Kyocera authorized dealer or Kyocera certified technician. Kyocera shall not
The minimum memory requirements for the printer with various options installed are listed in the table below. Please refer to this table when expanding the
printer's memory. Resolution Printing condition PCL 6, duplex mode = None PCL 6, duplex mode = On KPDL, duplex mode = None KPDL, duplex mode =
On PCL 6/KPDL resource protection, duplex mode = None PCL 6/KPDL, resource protection, duplex mode = On 300 dpi 8 MB 8 MB 8 MB 8 MB 600 dpi 8
MB 8 MB 8 MB 8 MB 10 MB 14 MB 1200 dpi Fast mode Fine mode 8 MB 8 MB 8 MB 12 MB 10 MB 14 MB 8 MB 12 MB 8 MB 12 MB 10 MB 14 MB
Removing the Main Circuit Board The main circuit board of the printer is equipped with two sockets for memory expansion. Expansion memory is available
in the form of a SIMM. The following instructions are intended for the technician only. Notes on Handling the Main Circuit Board and SIMM Protect the
electronics by taking these precautions: Ì Before touching the main circuit board, touch a water pipe or other large metal object to discharge yourself of static
electricity. While doing the work, it is recommended that you wear an antistatic wrist strap. Ì Touch the main circuit board and SIMM only by the edges. 1-23
Memory Expansion Installation Withdrawing the Main Circuit Board from the Printer Be sure to remove the memory card first if inserted in the printer's
memory card slot. Withdraw the main circuit board completely from the printer as follows: 1. Turn the printer's power off. Unplug the printer's power cable
Remove the three screws from the printer's rear cover. Power OFF (O) 3. Pull the main circuit board all the way out of the printer. Before pulling the main
Foreign objects, accidentally sticking to the back of the main board, can cause serious damage to the printer. Install the SIMM as described on the next page.
SIMM Sockets 1-24 1.7. Memory Expansion Installation SIMM to be used See your Kyocera dealer for purchasing information of the SIMMs that are best
suited for use with this printer. Either 4 MB, 8 MB, 16 MB or 32 MB SIMMs can be used for memory expansion. Installing and Removing SIMMs Installing
SIMMs Insert the SIMM into the socket as shown right. SIMM 1. Insert the connector end of the SIMM into the socket. 2.
Carefully push the board upright until it snaps into place. Make sure that the catches at the ends of the socket fit into the holes at the ends of the SIMM board.
Socket Catch Catch 1-25 1.7. Memory Expansion Installation Removing SIMMs To remove a SIMM, carefully pull the end catches slightly outwards and tilt
the SIMM as shown, then pull the SIMM out of the socket. Reverse the procedure under Withdrawing the Main Circuit Board from the Printer to put the main
circuit board back into the printer. Testing the Expansion Memory After you have finished installing SIMMs in the printer, test the printer to see if the
be liable for damage due to improper installation of the expansion memory.
and disconnect the printer from the host computer. 2.
board out, clean an area on the table, etc., at the back of the printer's rear panel.
installation has been successful.
You're reading an excerpt. Click here to read official KYOCERA
FS-1750 user guide
http://somemanuals.com/dref/324820
1.7.