Kyocera FS-1750 User Manual page 11

Power requirements are: Voltage Frequency Current capacity 120 V (U.S.A./Canada), 220 V to 240 V (European countries), ±10 % at each voltage 60 Hz
3 A at 220 V to 240 V FS-3750: Max. 7.8 A at 120 V, or Max. 4 A at 220 V to 240 V The outlet should be earthed, or an adapter should be used. If an
extension cord is used, the total length of the power cord plus extension should be 5 meters (17 feet) or less. Ì Well ventilated, not too hot or cold, and not too
damp or dry Temperature Humidity 10°C to 32.5°C (50°F to 90.5°F) 20% to 80% If you install the printer where the temperature or humidity is outside the
above ranges, you may not get the best print quality, and there will be an increased chance of paper jams. 1-2 1.2.
Unpacking and Inspection Power Supply The printer should not be on the same power circuit as an air conditioner, fluorescent light, copier, or shredder,
because these devices generate electrical noise on the power line. If it must share a power circuit with equipment like this, a high-frequency noise filter or
isolation transformer is advisable. (Filters and transformers are available commercially.) Avoid using plug multipliers to connect a large number of devices
on the same circuit as the printer. If the power from the outlet itself appears to be unstable, a line stabilizer should be used.
In places where the voltage tends to fluctuate, it may be necessary to install a voltage regulator. As the disconnect device is not incorporated in the printer's
AC primary circuit, an easily accessible socket outlet must be provided near the equipment. If the printer is used with the optional Sorter (SO-6) or Stacker
(ST-20), in order to avoid shortcircuiting, it should be ensured that these devices are plugged securely into their respective power outlets. Da kein
Trennschalter in den Wechselstrom-Primärkreis des Druckers eingebaut ist, muß eine leicht zugängliche Steckdose in der Nähe des Gerätes vorhanden sein.
Wenn der Drucker mit dem gesonderten Sorter (SO-6) oder Stapler (ST-20) verwendet wird, muß darauf geachtet werden, daß diese Geräte einwandfrei an
1.2. Unpacking and Inspection The printer is packed as shown below. Unpack the printer following diagrams 1 and 2 on the next page. While unpacking it,
check that the listed parts are all accounted for. Examine the package for any signs of damage that may have been caused during transportation. If the carton
is found to be badly damaged, leave the carton unopened and immediately notify the dealer from whom you purchased the printer. Save the box and other
packing materials in case you have to repack the printer for transportation at a later date. 1-3 1.2.
Unpacking and Inspection List of Shipped Components Ì Ì Ì Ì Ì (A) Face-up Output Tray (FS-3750 only) (B) Toner Kit (Box for the Developer Unit) (C) Power
Cord (D) User's Manual and Kyocera Digital Library (CD-ROM), including the printer drivers and manuals. (E) Paper Stopper (FS-3750 only) 1 (B) (A) 2
(D) (C) Printer (E) To remove the printer from the box, grasp the handholds on either side of the printer. Lift the printer from the carton as shown below. [
Always use these handholds whenever you lift or move the printer. [ The handhold on the right side of the printer doubles as the memory card slot. Be sure to
remove the memory card first, if inserted, before lifting or moving the printer. 1-4 1.3. Names of Parts 1.3.
Names of Parts This section takes you on a guided tour of the printer, pointing out its major parts. The part names introduced here will be used throughout
this manual. Front View Paper Full Sensor (Model FS-3750 only) Face-down Output Tray Paper Stopper Control Panel MP (Multi-Purpose) Tray Paper
Feed Unit Release Lever Power Switch Paper Cassette Side Cover Size Window Memory Card Slot Transfer Roller Option Paper Feeder Connector*
(120 V), ±2 % 50 Hz/60 Hz (220 V to 240 V), ±2 % FS-1750: Max. 5.8 A at 120 V, or Max.
separate Steckdosen angeschlossen sind, um Kurzschluß zu vermeiden.
Registration Roller MP Tray Paper Cassette Paper Feed Unit 1-5 1.
You're reading an excerpt. Click here to read official KYOCERA
FS-1750 user guide
http://somemanuals.com/dref/324820