Cleaning The Milk Frother With The Clean Button; Programming The Quantities Of Coffee And Milk In The Cup; Heating Water; Preparation - DeLonghi ESAM04.350 Instructions For Use Manual

Cleaning the milk frother with the ClEAN button

Important! Danger di scottature
When cleaning the internal tubes of the milk container, a little
hot water leaks out of the frothed milk tube (B5).
avoid contact with splashes of water.
"Press Clean button" flashes on the display each time you
use a milk function. To eliminate all milk residues, proceed as
follows:
1. leave the milk container in the machine (you do not need
to empty it);
2. Place a cup or other recipient under the frothed milk
spout.
3. Press the "Clean" button (fig. 23) and keep pressing until
the progress bar which appears on the display together
with the message "Cleaning underway" is complete;
4. remove the milk container and always clean the nozzle
with a sponge (fig. 24).
Please note!
• When "Press CLEAN button" flashes on the display, you
can still prepare any type of coffee or milk. if you have to
make a number of drinks with milk, wait until you have
delivered the last cup before cleaning the container.
• The milk left in the container can be kept in the
refrigerator.
• In some cases, to clean you must wait for the appliance to
heat up, holding the Clean button down.
Programming the quantities of coffee and milk in the
cup
The appliance is set by default to automatically deliver standard
quantities.
To change these quantities, proceed as follows:
1. Place a cup under the coffee spouts and milk spout.
2. Press the CAPPUCCINO button and hold down for at
least 8 seconds until the message "Milk for CaPPuCCino
Program Quantity" is displayed.
3. release the button. The appliance starts delivering milk.
4. once the required quantity of milk has been delivered into
the cup, press the CAPPUCCINO button again.
5. after a few seconds, the appliance starts delivering coffee
into the cup and the message "Coffee f. CaPPuCCino
Program Quantity" is displayed.
6. once the required quantity of coffee has been delivered
into the cup, press the CAPPUCCINO button. Coffee
delivery stops.
The machine is now reprogrammed with the new quantities.

HEATING WATER

Please note:
a few seconds may elapse between "energy saving" mode and
delivery of hot water; "Preparation underway..." is displayed.

Preparation

Important! Danger of burns.
never leave the machine unsupervised while delivering hot
water.
The hot water spout becomes hot while water is being delivered
and must be handled by the handle only.
1. Make sure the hot water spout is attached correctly
2. Place a container under the water spout (as close as
possible to avoid splashes) (fig. 4).
3. Press the button The message "hot Water" is
displayed.
4. Water flows out of the spout. delivery stops automatically
after about 250 ml.
5. To interrupt delivery of hot water manually, press the
button again.

Change the quantity of water delivered automatically.

The appliance is set by default to automatically deliver 250ml.
To modify these quantities, proceed as follows:
1. Position a container under the spout.
2. Press the button until the message "hot Water
Program Quantity" is displayed.
3. When the hot water in the cup reaches the required level,
press the button again.
The machine is now reprogrammed with the new quantity.

ClEANING

Important!
• Do not use solvents, abrasive detergents or alcohol to
clean the appliance. With de'longhi superautomatic
coffee makers, you need not use chemical products to
clean the machine.
• none of the components can be washed in a dishwasher
apart from the milk container (B).
• Do not use metal objects to remove encrustations or coffee
deposits as they could scratch metal or plastic surfaces.

Cleaning the coffee maker

The following parts of the machine must be cleaned regularly:
- coffee grounds container (a15),
- drip tray (a13),
- the inside of the machine, accessible after opening the
service door (a14),
14