Page 2
BEAN TO CUP ESPRESSO AND CAPPUCCINO MACHINE ESAM 03.105...
Page 3
ELECTRICAL REQUIREMENTS Before using this appliance ensure that the voltage indicated on the product corresponds with the main voltage in your home, if you are in any doubt about your supply contact your local electricity company. The flexible mains lead is supplied connected to a B.S. 1363 fused plug having a fuse of 13 amp capacity. Should this plug not fit the socket outlets in your home, it should be cut off and replaced with a suitable plug, following the procedure outlined below.
CONTENTS DESCALING ............14 SETTING WATER HARDNESS ........14 INTRODUCTION ............7 Measuring water hardness ............15 Symbols used in these instructions .......... 7 Set water hardness ..............15 Letters in brackets ..............7 Troubleshooting and repairs ............. 7 SETTING THE TEMPERATURE ........15 SAFETY ..............7 TECHNICAL SPECIFICATION ........15 Fundamental safety warnings ..........
INTRODUCTION SAFETY Thank you for choosing the „ESAM03.105“ bean to cup coffee Fundamental safety warnings maker. Danger! To get the best result of your new coffee machine please read This is an electrical appliance and may therefore cause electric these instructions carefully before use. This should ensure op- shock.
DESCRIPTION environments; • farm houses Description of the appliance • by clients in hotels, motels and other residential type en- (page 3 - A ) vironments A1. Grinding adjustment dial • bed and breakfast type environments. A2. Main switch A3. Beans container INSTRUCTIONS A4.
PRELIMINARY CHECKS 2. Remove the water tank, fill to the MAX line with fresh water then replace in the appliance (fig. 1). Checking the appliance 3. Turn the cappuccino maker outwards and place a contain- After removing the packaging, make sure the product is com- er with a minimum capacity of 100 ml underneath (fig.
A few seconds may elapse between energy saving mode and Danger of burns! delivery of the first coffee. During rinsing, a little hot water flows from the coffee spouts. Avoid contact with splashes of water. MAKING COFFEE To turn the appliance off, press the button (fig.
coffee mill is in operation. Please note: If the coffee is delivered too slowly or For hotter coffee, see the section “Tips for a hotter coffee”. not at all, turn one click clockwise to- wards “7”. For fuller bodied creamier Important! coffee, turn one click anticlockwise •...
For a richer denser froth, use skimmed or partially Cleaning the cappuccino maker after use. skimmed milk at refrigerator temperature (about 5°C). Clean the cappuccino maker each time you use it to avoid the To avoid milk with poor froth or large bubbles, always build-up of milk residues or blockages.
CLEANING cleaned. To remove the drip tray: 1. Remove the drip tray and the grounds container (fig. 19); Cleaning the coffee maker 2. Empty the drip tray and grounds container and wash The following parts of the machine must be cleaned regularly: them;...
Do not use washing up liquid to clean the infuser as it could Place an empty container with a minimum capacity of 1.5 cause damage. litres under the hot water spout. 4. Wait for the lights to come on stead- ily.
Measuring water hardness HIGH 1. Remove the “TOTAL HARDNESS TEST” indicator paper at- tached to this manual from its pack. 2. Immerse the paper completely in a glass of water for one second. 3. Remove the paper from the water and shake lightly. After about a minute, 1, 2, 3, or 4 red squares form, depending on the hardness of the water.
MEANING OF LIGHTS DURING NORMAL OPERATION LIGHTS DESCRIPTION MEANING The lights flash The water is not yet at the ideal temperature. Wait for the lights to come on steadily before ma- king coffee The lights are on steadily The appliance is ready to make coffee The light is on steadily The appliance is delivering one cup of coffee The light is on steadily...
MEANING OF THE ALARM LIGHTS LIGHTS DESCRIPTION MEANING WHAT TO DO The light is on steadily Insufficient water in the tank or Fill the tank with water and insert it correct- the tank is not correctly inserted ly, pushing it as far as it will go until it clicks into place.
LIGHTS DESCRIPTION MEANING WHAT TO DO The light is on steadily The infuser has not been replaced Insert the infuser as described in the para- after cleaning. graph “Cleaning the infuser” The inside of the appliance is very Clean the appliance thoroughly dirty The light flashes The service door is open...
Page 20
PROBLEM POSSIBLE CAUSE SOLUTION The appliance does not come • It is not plugged into the mains socket. • Plug into the mains socket. • The main switch (A8) is not turned on. • Place the main switch in the I position (fig. 3). When the steam/hot water •...