Preliminary Checks; Checking The Appliance; Installing The Appliance; Connecting The Appliance - DeLonghi ESAM04.350 Instructions For Use Manual

C4. MENU button: to access the settings menu.
C5.
by)
C6.
C7. CAPPUCCINO button to deliver a cappuccino or
frothed milk (press button twice)
C8.
you access the MENU: to scroll forwards through the
menu)
C9.
the MENU: ESC to exit the menu)
C10.
C11.

PRElIMINARY CHECKS

Checking the appliance

after removing the packaging, make sure the product is
complete and undamaged and that all accessories are present.
do not use the appliance if it is visibly damaged.
Contact de'longhi Customer Services.

Installing the appliance

Important!
When you install the appliance, you should respect the
following safety warnings:
• The appliance gives off heat. After positioning the
appliance on the worktop, leave a space of at least 3 cm
between the surfaces of the appliance and the side and
rear walls and at least 15 cm above the coffee maker.
• Water penetrating the appliance could cause damage. Do
not place the appliance near taps or sinks.
• The appliance could be damaged if the water it contains
freezes. do not install the appliance in a room where the
temperature could drop below freezing point.
• Arrange the power cable in such a way that it cannot be
damaged by sharp edges or contact with hot surfaces
(e.g. electric hot plates).

Connecting the appliance

Important!
s
Check that the mains power supply voltage corresponds to
the value indicated on the rating plate on the bottom of the
appliance.
n
Connect the appliance to an efficiently earthed and correctly
installed socket with a minimum current rating of 10a only.
s
if the power socket does not match the plug on the appliance,
d
have the socket replaced with a suitable type by a qualified
professional.
button: to turn the appliance on and off (stand-
button to deliver hot water.
button: to select coffee quantity (when
button: to select coffee taste (When you access
button: to perform a rinse cycle
button: to select pre-ground coffee

Using the appliance for the first time

Please note :
• Coffee has been used to factory test the appliance and it is
therefore completely normal for there to be traces of coffee
in the grinder. The machine is, however, guaranteed to be
new.
• you should customise water hardness as soon as possible
following the instructions in the section "Setting water
hardness" on page 17.
1. Plug the appliance into the mains socket and place the
main switch on the back of the appliance in the i position
(fig. 1).
you must first choose the language (the languages scroll
through at intervals of about 3 seconds).
2. When "english" appears, press the OK button (fig. 2). once
the language has been saved, the message "engliSh set"
is displayed.
Follow the instructions indicated by the appliance:
3. "FILL TANK": remove the water tank, fill to the MAX line
with fresh water then replace in the appliance (fig. 3).
4. "inSerT WaTer SPouT": Check that the hot water spout
is inserted on the nozzle and place a container holding a
minimum of 100 ml underneath (fig. 4).
5. "Hot water Press OK": press the OK button (fig. 2). " Please
wait" is displayed and the appliance begins to deliver
water from the hot water spout.
The appliance ends the first start up procedure, then the
message "Turning off Please wait" is displayed and the
appliance goes off.
The coffee maker is now ready for normal use.
Please note:
• When using the appliance for the first time, you need to
make 4-5 cups of coffee or 4-5 cappuccinos before the
appliance starts to give satisfactory results.

TURNING THE APPlIANCE ON

Please note:
Before turning the appliance on, make sure the main switch on
the back of the appliance is in the i position (fig. 1).
each time the appliance is turned on, it performs an automatic
preheat and rinse cycle which cannot be interrupted.
The appliance is ready for use only after completion of this
cycle.
9