Sound Setting; Adjusting Subwoofer/Bass/Treble/Balance (Between Left And Right)/Fader (Between Front And Rear)/Loudness/Defeat; Setting The Bass Control - Alpine iDA-X305S Owner's Manual

Sound Setting

Double Action encoder
/ENTER
(IMPRINT)
If either an external or IMPRINT audio processor is connected, the
Sound Setup screen is not displayed. For an external audio processor,
refer to "Audio Setting" (page 25) of "SETUP" (page 22) to adjust the
sound. For an IMPRINT audio processor, refer to "IMPRINT Operation
(Optional)" (page 26) to adjust the sound.
Adjusting Subwoofer/Bass/Treble/Balance
(Between Left and Right)/Fader (Between
Front and Rear)/Loudness/Defeat
1
Press (IMPRINT) repeatedly to choose the
desired mode.
Each press changes the mode as follows:
1
Subwoofer* Bass Level
Fader Loudness Defeat
Subwoofer: 00 ~ 15
Bass level: –7 ~ +7
Treble level: –7 ~ +7
Balance: Left15 ~ Right15
Fader: Rear15 ~ Front15
Loudness: ON/OFF
Defeat: ON/OFF
Volume: – ~ 0 dB
• Loudness introduces a special low and high frequency
emphasis at low listening levels. This compensates for the
ear's decreased sensitivity to bass and treble sound. The
function is inoperable when Defeat is set to ON.
• By setting Defeat ON, previously adjusted setting of Bass,
Treble and High Pass Filter will return to the factory defaults.
• If (IMPRINT) is not pressed for 15 seconds after selecting the
Subwoofer, Bass, Treble, Balance or Fader mode, the unit
automatically returns to normal mode.
1
* When the subwoofer mode is set to OFF, its level cannot be adjusted.
2
Rotate the Double Action encoder until the
desired sound is obtained in each mode.
• Depending on the connected devices, some functions do not work.
• You can store the contents of Balance/Fader/Loudness settings after
completing. For how to store, refer to "Storing the Audio Adjustment
Level (User Preset)" (page 25).
20
-EN
Treble Level Balance
Volume Subwoofer

Setting the Bass Control

You can change the Bass Frequency emphasis to create your own tonal
preference.
1
Press and hold (IMPRINT) for at least 2 seconds.
The Sound Setup screen is displayed.
2
Press /ENTER.
The Bass Adjustment setting mode is activated.
Setting the Bass Centre Frequency
3
Press /ENTER.
The F setting screen is displayed.
0
4
Press /ENTER.
5
Rotate the Double Action encoder to select the
desired bass centre frequency, and then press
/ENTER.
60 Hz 80 Hz 100 Hz
Emphasises the displayed bass frequency ranges.
6
Press to return to Bass Adjustment mode.
Setting the Bass Bandwidth
3
Rotate the Double Action encoder to select "Q",
and then press /ENTER.
The Q setting screen is displayed.
4
Press /ENTER.
5
Rotate the Double Action encoder to select the
desired bass bandwidth.
1 1.25 1.5 2
Changes the boosted bass bandwidth to wide or narrow. A
wider setting will boost a wide range of frequencies above
and below the centre frequency. A narrower setting will
boost only frequencies near the centre frequency.
6
Press to return to Bass Adjustment mode.
• If is pressed during setting, the unit returns to the previous item.
• The function is inoperable when Defeat is set to ON.
• You can adjust the bass level in normal mode. For details, refer to
"Adjusting Subwoofer/Bass/Treble/Balance (Between Left and Right)/
Fader (Between Front and Rear)/Loudness/Defeat" (page 20).
• After the setting, storing the setting contents on the unit is
recommended. For details, refer to "Storing the Audio Adjustment
Level (User Preset)" (page 25).
• The bass level settings will be individually memorized for each
source (FM, MW (LW), CD, etc.) until the setting is changed. The
bass frequency and bass bandwidth settings adjusted for one source
are effective for all other sources (FM, MW (LW), CD, etc.).
200 Hz