Page 1 2014 fordowner.com ford.ca EL2J 19A321 AA February 2014 Third Printing Owner’s Manual Explorer Litho in U.S.A.
Page 2: Table Of Contents
Table of Contents Introduction Child Safety Child seat positioning ........21 Booster seats .
Page 3: Table Of Contents
Table of Contents MyKey Settings, MyKey ........71 Creating.
Page 4: Table Of Contents
Table of Contents Lighting Lighting control ........101 Autolamps .
Page 5: Table Of Contents
Table of Contents Seats Sitting in the correct position ......156 Head restraints........157 Manual seats .
Page 6: Table Of Contents
Table of Contents Brakes Brakes ..........223 Hints on driving with anti-lock brakes .
Page 7: Table Of Contents
Table of Contents Load Carrying Cargo net ......... . .269 Roof racks and load carriers .
Page 8: Table Of Contents
Table of Contents Maintenance General information ........315 Opening and closing the hood .
Page 9: Table Of Contents
Table of Contents Wheels and Tires Tire care ......... . .357 Using snow chains .
Page 10: Table Of Contents
No part of this publication may be reproduced, transmitted, stored in a retrieval system or translated into any language in any form by any means without our written permission. Errors and omissions excepted. © Ford Motor Company 2014 2014 Explorer (exp) Owners Guide gf, 3rd Printing, September 2013...
Page 11: Introduction
Introduction ABOUT THIS MANUAL Thank you for choosing Ford. We recommend that you take some time to get to know your vehicle by reading this manual. The more that you know about it, the greater the safety and pleasure you will get from driving it.
Page 12 Introduction SYMBOL GLOSSARY WARNING: You risk death or serious injury to yourself and others if you do not follow the instruction highlighted by the warning symbol. These are some of the symbols you may see on your vehicle. Symbol Description Symbol Description Symbol...
Page 13 Introduction Symbol Description Symbol Description Symbol Description Fuel pump Fuse Hazard reset compartment warning flasher Heated rear Interior Jack window luggage compartment release Lighting Low tire Maintain control pressure correct fluid warning level Panic alarm Parking aid Parking system brake system Power Power Power...
Page 14 In order to properly diagnose and service your vehicle, Ford Motor Company, Ford of Canada, and service and repair facilities may...
Page 15 EDR. Ford Motor Company and Ford of Canada do not access event data recorder information without...
Page 16 See www.dtsc.ca.gov/hazardouswaste/perchlorate for more information. FORD CREDIT (U.S. ONLY) Ford Credit offers a full range of financing and lease plans to help you acquire your vehicle. If you have financed or leased your vehicle through Ford Credit, thank you for your business.
Page 17 Genuine Ford and Motorcraft replacement parts are the only replacement parts that benefit from a Ford Warranty. Damage caused to your vehicle as a result of the failure of non-Ford parts may not be covered by the Ford Warranty. For additional information, see the terms and conditions of the Ford Warranty.
Page 18 Your vehicle is not equipped with a snowplowing package. Using your vehicle as an ambulance Do not use this vehicle as an ambulance. Your vehicle is not equipped with the Ford Ambulance Preparation Package. MOBILE COMMUNICATIONS EQUIPMENT Using mobile communications equipment is becoming increasingly important in the conduct of business and personal affairs.
Page 19 Introduction EXPORT UNIQUE (NON–UNITED STATES/CANADA) VEHICLE SPECIFIC INFORMATION For your particular global region, your vehicle may be equipped with features and options that are different from the features and options that are described in this owner’s manual. A market unique supplement may be supplied that complements this book.
Page 20: Child Safety
NHTSA and other safety organizations, or are the minimum requirements of law. Ford recommends checking with a NHTSA Certified Child Passenger Safety Technician (CPST) and consulting your pediatrician to make sure your child seat is appropriate for your child, and is compatible with and properly installed in your vehicle.
Page 21 Child Safety Recommendations for Safety Restraints for Children Recommended Child size, height, weight, or age restraint type Infants Children weighing 40 lb (18 kg) or less Use a child safety (generally age four or younger). seat (sometimes toddlers called an infant carrier, convertible seat, or toddler seat).
Page 22: Child Seat Positioning
Child Safety • When possible, always properly restrain children twelve (12) years of age and under in a rear seating position of your vehicle. Accident statistics suggest that children are safer when properly restrained in the rear seating positions than in a front seating position. See Front Passenger Sensing System in the Supplementary Restraints System chapter for more information.
Page 23 Child Safety WARNING: Always restrain an unoccupied child seat or booster seat. These objects may become projectiles in a crash or sudden stop, which may increase the risk of serious injury. WARNING: Never place, or allow a child to place, the shoulder belt under a child’s arm or behind the back because it reduces the protection for the upper part of the body and may increase the risk of injury or death in a crash.
Page 24: Booster Seats
Child Safety Note: The child seat must rest tightly against the vehicle seat upon which it is installed. It may be necessary to lift or remove the head restraint. See the Seats chapter for information on head restraints. BOOSTER SEATS WARNING: Never place, or allow a child to place, the shoulder belt under a child’s arm or behind the back because it reduces the protection for the upper part of the body and may increase the risk...
Page 25 Child Safety Types of Booster Seats • Backless booster seats If your backless booster seat has a removable shield, remove the shield. If a vehicle seating position has a low seat back or no head restraint, a backless booster seat may place your child’s head (as measured at the tops of the ears) above the top of the seat.
Page 26 Child Safety Children and booster seats vary in size and shape. Choose a booster that keeps the lap belt low and snug across the hips, never up across the stomach, and lets you adjust the shoulder belt to cross the chest and rest snugly near the center of the shoulder.
Page 27: Installing Child Seats
Child Safety INSTALLING CHILD SEATS Child Seats Use a child safety seat (sometimes called an infant carrier, convertible seat, or toddler seat) for infants, toddlers or children weighing 40 pounds (18 kilograms) or less (generally age four or younger). Using Lap and Shoulder Belts WARNING: Airbags can kill or injure a child in a child seat.
Page 28 Child Safety • Keep the buckle release button pointing up and away from the safety seat, with the tongue between the child seat and the release button, to prevent accidental unbuckling. • Place the vehicle seat upon which the child seat will be installed in the upright position.
Page 29 Child Safety 2. After positioning the child safety seat in the proper seating position, do the following: • Standard safety belt: pull down on the shoulder belt and then grasp the shoulder belt and lap belt together behind the belt tongue.
Page 30 Child Safety • Standard safety belt buckle • Inflatable safety belt buckle 5. To put the retractor in the automatic locking mode, do the following; • Standard safety belt: grasp the shoulder portion of the belt and pull downward until all of the belt is pulled out.
Page 31 Child Safety • Inflatable safety belt: grasp the lap portion of the inflatable safety belt and pull upward until all of the belt is pulled out. Note: Unlike the standard safety belt, the inflatable safety belt’s unique lap portion locks the child seat for installation. The ability for the shoulder portion of the belt to move freely is normal, even after the lap belt has been put into the automatic locking mode.
Page 32 1 inch (2.5 centimeters) of movement for proper installation. Ford recommends checking with a NHTSA Certified Child Passenger Safety Technician to make certain the child restraint is properly installed. In Canada, check with your local St. John Ambulance office for referral to a Child Passenger Safety Technician.
Page 33 Child Safety Using Lower Anchors and Tethers for CHildren (LATCH) WARNING: Never attach two child safety seats to the same anchor. In a crash, one anchor may not be strong enough to hold two child safety seat attachments and may break, causing serious injury or death.
Page 34 Child Safety • Second-row bench seats and third-row passenger side The LATCH anchors are located at the rear section of the rear seat between the cushion and seat back below the symbols as shown. Follow the child seat manufacturer’s instructions to properly install a child seat with LATCH attachments.
Page 35 Child Safety Each time you use the safety seat, check that the seat is properly attached to the lower anchors and tether anchor, if applicable. Tug the child seat from side to side and forward and back where it is secured to your vehicle.
Page 36 Child Safety • Second-row bench seats and third-row passenger side Perform the following steps to install a child safety seat with tether anchors: Note: If you install a child seat with rigid LATCH attachments, do not tighten the tether strap enough to lift the child seat off your vehicle seat cushion when the child is seated in it.
Page 37 Child Safety 2. Locate the correct anchor for the selected rear seating position. • Second-row bucket (40/40) • Second-row bench (60/40) • Third-row seat Note: The cargo tie-downs at the rear edge of the floor are not tether anchors. 2014 Explorer (exp) Owners Guide gf, 3rd Printing, September 2013 USA (fus)
Page 38 If the safety seat is not anchored properly, the risk of a child being injured in a crash greatly increases. If your child restraint system is equipped with a tether strap, and the child restraint manufacturer recommends its use, Ford also recommends its use. 2014 Explorer (exp)
Page 39: Child Safety Locks
Child Safety CHILD SAFETY LOCKS When these locks are set, the rear doors cannot be opened from the inside. The childproof locks are located on the rear edge of each rear door and must be set separately for each door. •...
Page 40: Safety Belts
Safety Belts PRINCIPLES OF OPERATION WARNING: Always drive and ride with your seat back upright and the lap belt snug and low across the hips. WARNING: To reduce the risk of injury, make sure children sit where they can be properly restrained. WARNING: Never let a passenger hold a child on his or her lap while the vehicle is moving.
Page 41 Safety Belts WARNING: When possible, all children 12 years old and under should be properly restrained in a rear seating position. Failure to follow this could seriously increase the risk of injury or death. WARNING: Safety belts and seats can become hot in a vehicle that has been closed up in sunny weather;...
Page 42: Fastening The Safety Belts
Safety Belts FASTENING THE SAFETY BELTS The front outboard and rear safety restraints in your vehicle are combination lap and shoulder belts. 1. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) until you hear a snap and feel it latch.
Page 43 Safety Belts Pregnant women should always wear their safety belts. The lap belt portion of a combination lap and shoulder belt should be positioned low across the hips below the belly and worn as tight as comfort will allow. The shoulder belt should be positioned to cross the middle of the shoulder and the center of the chest.
Page 44 Safety Belts Automatic Locking Mode In this mode, the shoulder belt or lap belt is automatically pre-locked. The belt will still retract to remove any slack in the shoulder or lap belt. The automatic locking mode is not available on the driver safety belt. When to Use the Automatic Locking Mode This mode should be used any time a child safety seat, except a booster, is installed in passenger front or rear seating positions.
Page 45: Safety Belt Height Adjustment
Safety Belts Safety Belt Extension Assembly WARNING: Do not use extensions to change the fit of the shoulder belt across the torso. WARNING: Do not use extensions with an inflatable safety belt. Safety belt extensions are vehicle-specific. See an authorized dealer to make sure you obtain the proper safety belt extension for your vehicle.
Page 46: Safety Belt Warning Light And Indicator Chime
Safety Belts SAFETY BELT WARNING LIGHT AND INDICATOR CHIME This lamp illuminates and an audible warning will sound if the driver’s safety belt has not been fastened when the vehicle’s ignition is turned on. Conditions of Operation If... Then... The driver safety belt is not The safety belt warning light buckled before the ignition illuminates 1-2 minutes and the...
Page 47 Safety Belts If... Then... The driver and front passenger The Belt-Minder feature will not safety belts are buckled before activate. the ignition switch is turned to the on position or less than 1-2 minutes have elapsed since the ignition switch has been turned to on...
Page 48: Rear Inflatable Safety Belt
Safety Belts Read Steps 1 - 4 thoroughly before proceeding with the programming procedure. Before following the procedure, make sure that: • The parking brake is set. • The transmission is in park (P). • The ignition is off. • The driver and front passenger safety belts are unbuckled. 1.
Page 49 Safety Belts The rear inflatable safety belt consists of the following: • An inflatable bag located in the shoulder safety belt webbing. • Lap safety belt webbing with automatic locking mode. • Crash sensors and monitoring system with readiness indicator. See Crash Sensors and Airbag Indicator in the Supplemental Restraint System chapter.
Page 50: Child Restraint And Safety Belt Maintenance
Ford Motor Company recommends that all safety belt assemblies in use in vehicles involved in a crash be replaced. However, if the crash was minor and an authorized dealer finds that the belts do not show damage and continue to operate properly, they do not need to be replaced.
Page 51: Personal Safety System
Personal Safety System PERSONAL SAFETY SYSTEM™ The Personal Safety System provides an improved overall level of frontal crash protection to front seat occupants and is designed to help further reduce the risk of airbag-related injuries. The system is able to analyze different occupant conditions and crash severity before activating the appropriate safety devices to help better protect a range of occupants in a variety of frontal crash situations.
Page 52: Supplementary Restraints System
Supplementary Restraints System PRINCIPLES OF OPERATION WARNING: Airbags do not inflate slowly or gently, and the risk of injury from a deploying airbag is the greatest close to the trim covering the airbag module. WARNING: All occupants of your vehicle, including the driver, should always properly wear their safety belts, even when an airbag supplemental restraint system is provided.
Page 53 Supplementary Restraints System WARNING: If the airbag has deployed, the airbag will not function again and must be replaced immediately. If the airbag is not replaced, the unrepaired area will increase the risk of injury in a crash. The airbags are a supplemental restraint system and are designed to work with the safety belts to help protect the driver and right front passenger from certain upper body injuries.
Page 54: Driver And Passenger Airbags
Supplementary Restraints System DRIVER AND PASSENGER AIRBAGS WARNING: Never place your arm or any objects over an airbag module. Placing your arm over a deploying airbag can result in serious arm fractures or other injuries. Objects placed on or over the airbag inflation area may cause those objects to be propelled by the airbag into your face and torso causing serious injury.
Page 55 Supplementary Restraints System Proper Driver and Front Passenger Seating Adjustment WARNING: The National Highway Traffic Safety Administration recommends a minimum distance of at least 10 inches (25 centimeters) between an occupant’s chest and the driver airbag module. Failure to follow this could seriously increase the risk of injury or death.
Page 56: Front Passenger Sensing System
Supplementary Restraints System Knee Airbag System (Passenger’s Side Only) The knee airbag is located under the instrument panel. When the passenger’s front airbag activates in a crash, the passenger’s knee airbag will deploy. As with front and side airbags, it is important to be properly seated and restrained to reduce the risk of death or serious injury.
Page 57 Supplementary Restraints System The front passenger sensing system is designed to disable (will not inflate) the front passenger’s frontal airbag when the front passenger seat is unoccupied, or when a rear-facing infant seat, a forward-facing child restraint, or a booster seat is detected. Even with this technology, parents are strongly encouraged to always properly restrain children in the rear seat.
Page 58 If it is necessary to modify an advanced front airbag system to accommodate a person with disabilities, contact the Ford Customer Relationship Center at the phone number shown in the Getting the services you need section of the Customer Assistance chapter, or see your authorized dealer.
Page 59: Side Airbags
Supplementary Restraints System SIDE AIRBAGS WARNING: Do not place objects or mount equipment on or near the airbag cover, on the side of the seatbacks (of the front seats), or in front seat areas that may come into contact with a deploying airbag.
Page 60: Safety Canopy Curtain Airbags
Supplementary Restraints System The system consists of the following: • A tag on the seatback indicating that side airbags are found on your vehicle. • Side airbags located inside the seatback of the driver and front passenger seats. • Crash sensors and monitoring system with readiness indicator.
Page 61 Supplementary Restraints System WARNING: All occupants of your vehicle including the driver should always wear their safety belts even when an airbag supplemental restraint system and curtain airbag is provided. Failure to properly wear your safety belt could seriously increase the risk of injury or death.
Page 62: Crash Sensors And Airbag Indicator
Supplementary Restraints System • Crash sensors and monitoring system with readiness indicator. See Crash Sensors and Airbag Indicator in this chapter. Children 12 years old and under should always be properly restrained in the rear seats. The Safety Canopy will not interfere with children restrained using a properly installed child or booster seat because it is designed to inflate downward from the headliner above the doors along the side window opening.
Page 63: Airbag Disposal
Supplementary Restraints System A difficulty with the system is indicated by one or more of the following: • The readiness light will either flash or stay lit. • The readiness light will not illuminate immediately after the ignition is turned on. •...
Page 64: Keys And Remote Control
Keys and Remote Control GENERAL INFORMATION ON RADIO FREQUENCIES This device complies with part 15 of the FCC Rules and with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
Page 65: Remote Control
Keys and Remote Control REMOTE CONTROL Integrated Keyhead Transmitters (IKTs) (If Equipped) Use the key blade to start your vehicle and unlock or lock the driver door from outside your vehicle. The transmitter portion functions as the remote control. Note: Your vehicle’s keys came with a security label that provides important key cut information.
Page 66 Keys and Remote Control Note: Your vehicle’s back-up keys came with a security tag that provides important key cut information. Keep the tag in a safe place for future reference. Replacing the Battery Note: Refer to local regulations when disposing of transmitter batteries. Note: Do not wipe off any grease on the battery terminals or on the back surface of the circuit board.
Page 67 Keys and Remote Control Intelligent Access Transmitter 1. Remove the backup key from the transmitter. 2. Twist a thin coin under the tab hidden behind the backup key head to remove the battery cover. Do not use the backup key to remove the cover or you could damage the intelligent access key.
Page 68 Keys and Remote Control Programming Memory to the Remote Control 1. Turn the ignition on. 2. Move the memory features to the desired positions using the associated controls. 3. Press and hold button 1 for five seconds. A tone will sound in about two seconds.
Page 69 Keys and Remote Control Remote Start (If Equipped) WARNING: To avoid exhaust fumes, do not use remote start if your vehicle is parked indoors or areas that are not well ventilated. Note: Do not use remote start if your vehicle is low on fuel. The remote start button is on the transmitter.
Page 70 Keys and Remote Control Remote Starting the Vehicle Note: You must press each button within three seconds of each other. Your vehicle will not remote start and the horn will not sound if you do not follow this sequence. The label on your transmitter details the starting procedure.
Page 71: Replacing A Lost Key Or Remote Control
Keys and Remote Control Turning the Vehicle Off After Remote Starting Press the button once. The parking lamps will turn off. You may have to be closer to your vehicle than when starting due to ground reflection and the added noise of the running vehicle. You can disable or enable the remote start system through the information display.
Page 72: Mykey
MyKey PRINCIPLES OF OPERATION MyKey allows you to program keys with restricted driving modes to promote good driving habits. All but one of the keys programmed to the vehicle can be activated with these restricted modes. Any keys that have not been programmed are referred to as administrator keys or admin keys.
Page 73: Creating
MyKey Configurable Settings With an admin key, you can configure certain MyKey settings when you first create a MyKey and before you recycle the key or restart the engine. You can also change the settings afterward with an admin key. •...
Page 74: Clearing
MyKey Programming/Changing Configurable Settings Use the information display to access your configurable MyKey settings: 1. Switch the ignition on using an admin key. If your vehicle has push-button start, put the intelligent access key fob into the backup slot. The location of your backup slot is in another chapter. See Starting and Stopping the Engine 2.
Page 75 USING MYKEY WITH REMOTE START SYSTEMS MyKey is not compatible with non-Ford-approved aftermarket remote start systems. If you choose to install a remote start system, please see your Ford authorized dealer for a Ford-approved remote start system. MYKEY TROUBLESHOOTING Condition Potential causes •...
Page 76 MyKey Condition Potential causes • Purchase a new key from your authorized I lost the only admin key. dealer. • Program a spare key. See SecuriLock in the I lost a key. Security. • An admin fob is present at engine start. No MyKey functions •...
Page 77: Locks
Locks LOCKING AND UNLOCKING You can use the power door lock control or the remote control to lock and unlock your vehicle. Power Door Locks The power door lock control is located on the driver and front passenger door panels. A.
Page 78 Locks Locking the Doors Press the button to lock all the doors. The turn signals will illuminate. Press the button again within three seconds to confirm that all the doors are closed. The doors will lock again, the horn will sound and the turn signals will illuminate if all the doors and the luggage compartment are closed.
Page 79 Locks At the Front Doors Pull a front exterior door handle to unlock and open the door. The unlock sensor is on the back of the handle. Make sure not to touch the lock sensor area on the front of the handle. Press and hold the lock sensor area for about a second to lock your vehicle.
Page 80 Locks Smart Unlocks for Intelligent Access Keys (If Equipped) This feature helps to prevent you from unintentionally locking your intelligent access key inside your vehicle’s passenger compartment or rear cargo area. When you lock your vehicle using the driver or passenger power door lock control (with the door open, transmission in P and ignition off), after you close the door your vehicle will search for an intelligent access key in the passenger compartment.
Page 81 Locks Autounlock Feature (If Enabled) The autounlock feature unlocks all the doors when: • the ignition is on, all the doors are closed, and your vehicle has been in motion at a speed greater than 12 mph (20 km/h); • your vehicle has then come to a stop and you switch the off ignition or to accessory;...
Page 82 Locks Illuminated Exit The interior lamps and select exterior lamps illuminate when all doors are closed and you switch the ignition off and remove the key from the ignition (integrated keyhead transmitter only). The lamps turn off if all the doors remain closed and: •...
Page 83 Locks Note: Do not hang anything, for example a bike rack, from the spoiler, glass or liftgate. This could damage the liftgate and its components. Note: Do not leave the liftgate open while driving. This could damage the liftgate and its components. The liftgate area is only intended for cargo, not passengers.
Page 84 Locks Opening and Closing the Power Liftgate Note: You can reverse the liftgate movement direction with a second press of the instrument panel button, or the control button on the liftgate, or a second double press of the transmitter button. The liftgate will only operate with the transmission in P.
Page 85 Locks To close with the rear cargo area control: Press and release the button. WARNING: Keep clear of the liftgate when activating the rear switch. Setting Liftgate Open Height 1. Open the liftgate. 2. Manually move the liftgate to the desired height. 3.
Page 86: Securicode™ Keyless Entry Keypad
Locks When opening: The system will stop and a tone will sound three times when it detects an obstacle. Remove the obstacle to operate the liftgate. Resetting the Power Liftgate The liftgate may not operate properly and you may need to reset it if any of these conditions occur: •...
Page 87 Locks Programming a Personal Entry Code To create your own personal entry code: 1. Enter the factory-set code. 2. Press the 1•2 on the keypad within five seconds. 3. Enter your personal 5-digit code. You must enter each number within five seconds of each other.
Page 88 Locks Anti-Scan Feature The keypad will go into an anti-scan mode if you enter the wrong code seven times (35 consecutive button presses). This mode disables the keypad for one minute and the keypad lamp will flash. The anti-scan feature will turn off after: •...
Page 89: Security
Security SECURILOCK® PASSIVE ANTI-THEFT SYSTEM Note: The system is not compatible with non-Ford aftermarket remote start systems. Use of these systems may result in vehicle starting problems and a loss of security protection. Note: Metallic objects, electronic devices or a second coded key on the same key chain may cause vehicle starting issues if they are too close to the key when starting your vehicle.
Page 90 Security Store an extra programmed key away from the vehicle in a safe place to help prevent any inconveniences. See an authorized dealer to purchase additional spare or replacement keys. Programming a Spare Integrated Keyhead Transmitter Note: You can program a maximum of eight coded keys to your vehicle. Only four of these eight can be integrated keyhead transmitters.
Page 91 Security Wait 20 seconds and repeat Steps 1 through 8 if programming the key was not successful. Take your vehicle to an authorized dealer to have the new key programmed if you are still unsuccessful. Wait 20 seconds and then repeat this procedure from Step 1 to program an additional key.
Page 92: Anti-Theft Alarm
Security 5. Press and release the brake pedal one time. The indicator on the START/STOP button should begin to flash rapidly. This indicates the vehicle is in programming mode and that it has detected two programmed intelligent access keys in the vehicle. 6.
Page 93 Security Disarming the Alarm To disarm the alarm, do any of the following: • Press the power door unlock button within the 20-second pre-armed mode. • Press the unlock button on the remote control. • Unlock the doors with the keyless entry pad. •...
Page 94: Steering Wheel
Steering Wheel ADJUSTING THE STEERING WHEEL WARNING: Do not adjust the steering wheel when your vehicle is moving. Note: Make sure that you are sitting in the correct position. See Sitting in the Correct Position in the Seats chapter. 1. Unlock the steering column. 2.
Page 95 Steering Wheel Power Tilt and Telescope Steering Column (If Equipped) WARNING: Do not adjust the steering wheel when your vehicle is moving. Note: Make sure that you are sitting in the correct position. Refer to Sitting in the Correct Position in the Seats chapter. Use the control on the side of the steering column to adjust the position.
Page 96 Steering Wheel To reset the steering column to its normal stopping position: 1. Press the steering column control again after encountering the new stopping position. 2. Continue pressing the control until it reaches the end of the column position. A new stopping position is set. The next time you tilt or telescope the steering column, it will stop just short of the end of the column position.
Page 97 Steering Wheel CRUISE CONTROL Type 1 Type 2 CNCL See the Cruise Control chapter for information on this feature. INFORMATION DISPLAY CONTROL See the Information Displays chapter for more information. 2014 Explorer (exp) Owners Guide gf, 3rd Printing, September 2013 USA (fus)
Page 98 Steering Wheel Cluster Display Control Features If equipped with: MyFord system: This control functions the same as the center control on the faceplate. See MyFord system in the Audio Systems chapter. MyFord Touch: Use this control to adjust the right side of the cluster display.
Page 99: Pedals
Pedals ADJUSTABLE PEDALS (IF EQUIPPED) WARNING: Never adjust the accelerator and brake pedal with feet on the pedals while the vehicle is moving. The control is located on the left side of the steering column. Press and hold the appropriate control to move the pedals. A.
Page 100: Wipers And Washers
Wipers and Washers WINDSHIELD WIPERS Note: Fully defrost the windshield in icy conditions before turning on the windshield wipers. Note: Make sure the windshield wipers are switched off before entering a car wash. Note: Clean the windshield and wiper blades if they begin to leave streaks or smears.
Page 101: Windshield Washers
Wipers and Washers Keep the outside of the windshield clean, especially the area around the interior mirror where the sensor is located, or sensor performance may be affected. WINDSHIELD WASHERS Note: Do not operate the wipers on a dry windshield. This may scratch the glass, damage the wiper blades or cause the wiper motor to burn out.
Page 102: Lighting
Lighting LIGHTING CONTROL A. Off B. Parking lamps, instrument panel lamps, license plate lamps and tail lamps C. Headlamps High Beams Push the lever forward to switch the high beams on. Push the lever forward again or pull the lever toward you to switch the high beams off.
Page 103: Autolamps
Lighting AUTOLAMPS WARNING: In severe weather conditions, it may be necessary to switch your headlamps on manually. Note: If the vehicle is equipped with autolamps, it will have the windshield wiper rainlamp feature. When the windshield wipers are turned to low- or high-speed wiping during daylight, and the headlamp control is in the autolamp position, the exterior lamps will turn on after a brief delay and will remain on until the wipers are turned off.
Page 104: Headlamp Exit Delay
Lighting HEADLAMP EXIT DELAY You can set the delay time to keep the headlamps on for up to three minutes after the ignition is turned off. Follow the steps below to change the delay time (Steps 1 through 6 must be done within 10 seconds): 1.
Page 105: Automatic High Beam Control
Lighting AUTOMATIC HIGH BEAM CONTROL (IF EQUIPPED) The system will automatically turn on your high beams if it is dark enough and no other traffic is present. When it detects an approaching vehicle’s headlights, a preceding vehicle’s tail lamps or street lighting, the system will turn off the high beams (low beams remain on) before they distract other drivers.
Page 106: Front Fog Lamps
Lighting • Severe rain, snow or fog is detected. • The camera is blocked. Activating the system Switch the system on within the information display. See Information displays. Turn the lighting control to the autolamps position. Manually overriding the system When the automatic control has activated high beams, pushing or pulling the stalk will provide a...
Page 107: Direction Indicators
Lighting DIRECTION INDICATORS The turn signal lever does not mechanically lock in the upward or downward position when activated. The turn signal control activation and cancellation is electronic. • Push down to activate the left turn signal. • Push up to activate the right turn signal.
Page 108 Lighting With fog lamps Use to manually turn the dome lamp on. • Press the control. This will turn on the interior courtesy lights. The lights will remain on until the control is pressed again. Front Row Map Lamps (If Equipped) To turn on the map lamps, press the outer edge of the clear lens.
Page 109 Lighting Second row dome/courtesy lamps (if equipped) The dome lamp lights when: • any door is opened. • the instrument panel dimmer button is pressed until the courtesy lamps come on. • any of the remote entry controls are pressed and the ignition is off. The courtesy lamp can also be turned on and off manually by pressing the lens depression.
Page 110: Windows And Mirrors
Windows and Mirrors POWER WINDOWS WARNING: Do not leave children unattended in your vehicle and do not let children play with the power windows. They may seriously injure themselves. WARNING: When closing the power windows, you should verify they are free of obstructions and make sure that children and pets are not in the proximity of the window openings.
Page 111 Windows and Mirrors Window Lock Press the control to lock or unlock the rear window controls. Bounce-Back The window will stop automatically while closing and reverse some distance if there is an obstacle in the way. Overriding the Bounce-Back Feature WARNING: When you override the bounce-back feature the window will not reverse if it detects an obstacle.
Page 112: Exterior Mirrors
Windows and Mirrors EXTERIOR MIRRORS Power Exterior Mirrors WARNING: Do not adjust the mirror while your vehicle is in motion. A. Left mirror B. Adjustment control C. Right mirror To adjust your mirrors: 1. Press the button to select the mirror you want to adjust. An indicator light on the button will illuminate.
Page 113 Windows and Mirrors Power-Folding Mirrors (If Equipped) Note: Activating the button 10 or more times within one minute, or repeated folding and unfolding of the mirrors while holding the button down during full travel, may disable the system to protect motors from overheating.
Page 114 Windows and Mirrors Integrated Blind Spot Mirrors (If Equipped) WARNING: Objects in the blind spot mirror are closer than they appear. Blind spot mirrors have an integrated convex mirror built into the upper outboard corner of the exterior mirrors. They are designed to assist you by increasing visibility along the side of your vehicle.
Page 115: Interior Mirrors
Windows and Mirrors INTERIOR MIRROR WARNING: Do not adjust the mirror when your vehicle is moving. Note: Do not clean the housing or glass of any mirror with harsh abrasives, fuel or other petroleum or ammonia based cleaning products. You can adjust the interior mirror to your preference. Some mirrors also have a second pivot point.
Page 116: Moonroof
Windows and Mirrors Illuminated Visor Vanity Mirror (If Equipped) Lift the cover to switch on the lamp. DUAL PANEL MOONROOF AND POWER SUNSCREEN (IF EQUIPPED) WARNING: Do not let children play with the moon roof or leave children unattended in the vehicle. They may seriously hurt themselves.
Page 117 Windows and Mirrors Opening and Closing the Moonroof Press and release the SLIDE control to open the moonroof. The sunscreen, if closed, will automatically open prior to opening the moonroof. The moonroof will stop short of the fully opened position. Note: This position helps to reduce rumbling wind noise which may happen with the roof fully open.
Page 118: Instrument Cluster
Instrument Cluster GAUGES Type 1 Cluster shown in standard measure – metric clusters similar. A. Tachometer B. Information display. See Information displays for more information. C. Speedometer D. Fuel gauge Fuel Gauge Indicates approximately how much fuel is left in the fuel tank (when the ignition is on).
Page 119: Warning Lamps And Indicators
Instrument Cluster Type 2 Cluster shown in standard measure – metric clusters similar. A. Left information display. See Information displays for more information. B. Speedometer C. Right information display. See MyFord Touch® for more information. WARNING LAMPS AND INDICATORS There are indicators that can alert you to a vehicle condition that may become serious enough to cause expensive repairs.
Page 120 Instrument Cluster Adaptive cruise control (RTT) (if equipped) The speed control system indicator light changes color to indicate what mode the system is in: • On (gray light): Illuminates when the adaptive cruise control system is turned on. Turns off when the speed control system is turned off.
Page 121 Instrument Cluster Charging system (RTT) Illuminates when the battery is not charging properly. If it stays on while the engine is running, there may be a malfunction with the charging system. Contact your authorized dealer as soon as possible. This indicates a problem with the electrical system or a related component.
Page 122 Instrument Cluster Hill descent (RTT) (if equipped) Illuminates when hill descent is turned on. High beams Illuminates when the high-beam headlamps are on. Low fuel (RTT) Illuminates when the fuel level in the fuel tank is at or near empty. Liftgate ajar (RTT) Illuminates when the ignition is on and liftgate is not completely closed.
Page 123 Instrument Cluster Safety belt Reminds you to fasten your safety belt. A Belt-Minder® chime will also sound to remind you to fasten your safety belt. Service engine soon The service engine soon indicator light illuminates when the ignition is first turned to the on position to check the bulb and to indicate whether the vehicle is ready for Inspection/Maintenance (I/M) testing.
Page 124: Audible Warnings And Indicators
Instrument Cluster Stability Control System Displays when the AdvanceTrac®/Traction control is active. If the light remains on, have the system serviced immediately. Stability Control System Off Illuminates when AdvanceTrac®/Traction control has been disabled by the driver. Transmission Tow/Haul Feature (RTT) (if equipped) Displays when the Tow/Haul feature has been activated.
Page 125: Information Displays
Information Displays GENERAL INFORMATION WARNING: Driving while distracted can result in loss of vehicle control, crash and injury. We strongly recommend that you use extreme caution when using any device that may take your focus off the road. Your primary responsibility is the safe operation of your vehicle.
Page 126 Information Displays Menu You can access the menus using the information display control. Note: Some options may appear slightly different or not at all if the items are optional. †Trip 1 & 2 Distance to E Trip Odometer Trip Timer Inst Fuel Econ Average Fuel Fuel Used...
Page 127 Information Displays Settings Driver Assist Traction Ctrl — check enabled (default) / uncheck disabled Blind Spot — check enabled (default) / uncheck disabled Collision Warning Sensitivity (if MyKey High, Normal or Low is programmed) Cross Traffic — check enabled (default) / uncheck disabled Cruise Control Adaptive or Normal Driver Alert —...
Page 128 Information Displays Settings Convenience Auto Highbeam — check enabled (default) / uncheck disabled Autolamp Delay Off or number of seconds Compass Display Display — check enabled (default) / uncheck disabled Calibrate Hold OK to calibrate Circle slowly to calibrate Calibration complete Zone Zone 1 —...
Page 129: Trip Computer
Information Displays Trip Computer Resetting the Trip Computer Press and hold OK on the current screen to reset the respective trip, distance, time and fuel information. Trip Odometer Registers the mileage of individual journeys. Distance to E Indicates the approximate distance the vehicle will travel on the fuel remaining in the tank.
Page 130 Information Displays Main menu From the main menu bar on the left side of the information display, you can choose from the following categories: • Display Mode • Trip 1 & 2 • Fuel Economy • Driver Assist • Settings Scroll up/down to highlight one of the categories, then press the right arrow key to enter into that category.
Page 131 Information Displays • Fuel gauge: Indicates approximately how much fuel is left in the fuel tank. The fuel gauge may vary slightly when the vehicle is in motion or on a grade. When the fuel level becomes low, the level indicator will change to amber.
Page 132 Information Displays Fuel Economy Use the left/right arrow buttons to choose the desired fuel economy display. Fuel Economy Inst Fuel XX. Min Fuel Fuel Economy Economy History Instantaneous fuel usage Fuel usage over a 30 minute time span Average fuel economy Always Present XXX mi (km) to empty Always Present...
Page 133 Information Displays Settings In this mode, you can configure different driver setting choices. Note: Some items are optional and may not appear. Settings Vehicle DTE Calculation Normal / Towing Easy Entry/Exit — check enabled / uncheck disabled Lighting Auto highbeam On / Off Autolamp Delay Off or number of...
Page 134: Information Messages
Information Displays Settings (cont’d) *MyKey MyKey Status MyKeys / Admin Keys Create Hold OK to Create MyKey MyKey 911 Assist Always On / User Selectable Traction Always On / User Selectable Control Max Speed Choose desired speed or off Speed Choose desired speed or off Warning Volume...
Page 135 Information Displays Message indicators: Some messages will be supplemented by a system specific symbol. Adaptive Cruise Action / Description Control Messages Adaptive Cruise Displayed when a radar malfunction is Malfunction preventing the ACC from engaging. Adaptive Cruise Not Displayed when conditions exist such that the Available adaptive cruise cannot function properly.
Page 136 Information Displays AWD/4WD Messages Action / Description AWD Off Displayed when the system has been automatically disabled to protect itself. This is caused by operating the vehicle with the compact spare tire installed or if the system is overheating. The system will resume normal function and clear this message after driving a short distance with the road tire re-installed or after the system is allowed to cool.
Page 137 Information Displays Battery and Action / Description Charging System Messages Transport Mode Contact your authorized dealer as soon as Contact Dealer possible. Factory Mode Contact Contact your authorized dealer as soon as Dealer possible. Low Battery Features Displayed when the battery management system detects an extended low-voltage Tempor.
Page 138 Information Displays Brake System Action / Description Messages Brake Fluid Level Low Indicates the brake fluid level is low and the brake system should be inspected immediately. Check Brake System Displayed when the brake system needs servicing. If the warning stays on or continues to come on, contact your authorized dealer as soon as possible.
Page 139 Information Displays Door Messages Action / Description X Door Ajar Displayed when a door is not completely closed. Liftgate Ajar Displayed when the liftgate is not completely closed. Driver Alert Action / Description Messages Driver Alert Warning Stop and rest as soon as it is safe to do so. Rest Now Driver Alert Warning Take a rest break soon.
Page 140 Information Displays Keys and Intelligent Action / Description Access Messages Press Brake to Start Displayed when the start/stop button is pressed without the brake pedal being applied. This is a reminder that the brake pedal must be applied when the start/stop button is pressed in order to start the engine.
Page 141 Information Displays Maintenance Action / Description Messages LOW Engine Oil Stop the vehicle as soon as safely possible, Pressure turn off the engine. Check the oil level. If the warning stays on or continues to come on with your engine running, contact your authorized dealer as soon as possible.
Page 142 Information Displays MyKey® Messages Action / Description Vehicle Near MyKey Displayed when a MyKey® is in use and the Top Speed MyKey speed limit is on and the vehicle speed is 80 mph (130 km/h). Vehicle Near MyKey Displayed when a MyKey® is in use and the Top Speed MyKey speed limit is on and the vehicle speed is approaching 80 mph (130 km/h).
Page 143 Information Displays Reminder Messages Action / Description Steering Lock Turn Displays when you need to turn the steering Wheel to Unlock wheel in order to disengage the steering lock. Shift to Park Displays as a reminder to shift into park if gear shift lever is not in park and a door is opened.
Page 144 Information Displays Terrain Management Action / Description / Off Road / Hill Descent Messages Hill Descent Control Displayed when hill descent control mode is Ready activated. Terrain Management Displays driver selected terrain management Normal Mode normal mode. Normal Mode Active Displays terrain management normal mode is currently active.
Page 145 Information Displays Tire Messages Action / Description Low Tire Pressure Displays when one or more tires on your vehicle have low tire pressure. Tire Pressure Monitor Displays when the tire pressure monitoring Fault system is malfunctioning. If the warning stays on or continues to come on, contact your authorized dealer.
Page 146: Climate Control
Climate Control MANUAL CLIMATE CONTROL A. Power: Press the button to turn the system on and off. Switching off the climate control system prevents outside air from entering the vehicle. B. Air distribution control: Press these buttons to turn airflow from the windshield, instrument panel, or footwell vents on or off.
Page 147 Climate Control F. Front temperature control: Controls the temperature of the airflow in the front of your vehicle. Adjust to select the desired temperature. G. Rear fan speed control: Controls the volume of air circulated in the rear of your vehicle. Press + or - to select the desired fan speed. H.
Page 148 Climate Control AUTOMATIC CLIMATE SYSTEM (WITH SONY® AUDIO SYSTEM) Note: You can switch temperature units between Fahrenheit and Celsius. See Menu features in the MyFord Touch or MyLincoln Touch chapter. A. CLIMATE: Press the button to turn the system on and off. Switching off the climate control system prevents outside air from entering the vehicle.
Page 149 Climate Control E. A/C: Press the button to turn air conditioning compressor on or off. Use air conditioning with recirculated air to improve cooling performance and efficiency. F. MAX A/C: Press the button to maximize cooling. Recirculated air flows through the instrument panel vents, air conditioning automatically turns on, and the fan automatically adjusts to the highest speed.
Page 150 Climate Control AUTOMATIC CLIMATE CONTROL (WITH MyTemp) DUAL TEMP AUTO Note: You can switch temperature units between Fahrenheit and Celsius. See Settings in the MyFord Touch or MyLincoln Touch chapter. A. MyTemp: Allows you to quickly adjust to a frequently used setting with a single touch.
Page 151 Climate Control E. MAX A/C: Press the button to maximize cooling. Recirculated air flows through the instrument panel vents, air conditioning automatically turns on, and the fan automatically adjusts to the highest speed. F. A/C: Press the button to turn air conditioning compressor on or off. Use air conditioning with recirculated air to improve cooling performance and efficiency.
Page 152 Climate Control E. REAR LOCK: Illuminates when the rear (auxiliary) climate system is being controlled by the front controls. The rear (auxiliary) climate controls do not work when this graphic is illuminated F. Temperature control: Controls the temperature of the airflow in the rear of your vehicle.
Page 153 Climate Control Heating the Interior Quickly Vehicles with manual climate Vehicles with automatic control climate control Adjust the fan speed to the Press the AUTO button. highest speed setting. Adjust the temperature control Adjust the temperature control to the highest setting. to the desired setting.
Page 154 Climate Control Recommended Settings for Cooling Vehicles with manual climate Vehicles with automatic control climate control Adjust the fan speed to the Press the AUTO button. center setting. Adjust the temperature control Adjust the temperature control to the midway point of the cold to the desired setting.
Page 155: Cabin Air Filter
Climate Control HEATED WINDOWS AND MIRRORS (IF EQUIPPED) Heated Rear Window Note: The ignition must be switched on to use this feature. Press the button to clear the rear window of thin ice and fog. Press the button again within 10 minutes to switch it off. It switches off automatically after 10 minutes, or when you switch the ignition off.
Page 156 Climate Control For more information regarding the interval at which you should replace the cabin air filter, see the Scheduled Maintenance chapter. For additional cabin air filter information, or to replace the filter, see an authorized dealer. REMOTE START (IF EQUIPPED) The remote start feature allows you to pre-condition the interior of your vehicle.
Page 157: Seats
Seats SITTING IN THE CORRECT POSITION WARNING: Sitting improperly out of position or with the seat back reclined too far can take off weight from the seat cushion and affect the decision of the passenger sensing system, resulting in serious injury or death in a crash. Always sit upright against your seat back, with your feet on the floor.
Page 158: Head Restraints
Seats • Bend your legs slightly so that you can press the pedals fully. • Position the shoulder strap of the safety belt over the center of your shoulder and position the lap strap tightly across your hips. Make sure that your driving position is comfortable and that you can maintain full control of your vehicle.
Page 159 Seats Second-row center seat head restraint (if equipped) The head restraints consist of: A. Energy absorbing head restraint B. Steel stems C. Guide sleeve adjust and release button D. Guide sleeve unlock and remove button • Raise: Pull up on the head restraint (A). •...
Page 160 Seats Second-row outboard seat head restraints The head restraints consist of: A. Energy absorbing head restraint B. Steel stems C. Guide sleeve unlock and remove buttons D. Fold strap • Fold: Pull the fold strap (D). Pull it back up to reset. •...
Page 161: Manual Seats
Seats Tilting Head Restraints (If Equipped) The front head restraints may tilt for extra comfort. To tilt the head restraint, do the following: 1. Adjust the seatback to an upright driving or riding position. 2. Tilt the head restraint forward by gently pulling the top of the head restraint.
Page 162: Power Seats
Seats Moving the seats backward and forward WARNING: Rock the seat backward and forward after releasing the lever to make sure that it is fully engaged. Lumbar adjustment (if equipped) POWER SEATS (IF EQUIPPED) WARNING: Never adjust the driver seat or seatback when the vehicle is moving.
Page 163 Seats Power Seat Adjustments Power Lumbar 2014 Explorer (exp) Owners Guide gf, 3rd Printing, September 2013 USA (fus)
Page 164: Memory Function
Seats MEMORY FUNCTION (IF EQUIPPED) This memory control, located on the driver door, allows automatic positioning of the driver seat and power mirrors to three programmable positions. You may also have this feature for the steering column and power adjustable foot pedals.
Page 165: Heated Seats
Seats Easy Entry and Exit Feature (If Equipped) This feature can move the seat rearward and the optional steering column up and forward to allow extra room to exit the vehicle. This occurs when: • You place the transmission in neutral (N) or park (P), and •...
Page 166 Seats To operate the heated seats: Press the heated seat symbol to cycle through the various heat settings and off. Warmer settings are indicated by more indicator lights. HEATED AND COOLED SEATS (IF EQUIPPED) Heated Seats WARNING: Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion, or other physical conditions, must exercise care when using the seat heater.
Page 167 Seats Cooled Seats The cooled seats will only function when the engine is running. To operate the cooled seats: Press the cooled seat symbol to cycle through the various cooling settings and off. Cooler settings are indicated by more indicator lights. If the engine falls below 350 RPM while the cooled seats are on, the feature will turn itself off.
Page 168: Rear Seats
Seats To install a filter: 1. First, position the filter in its housing making sure that the far forward end is all the way up in the housing. 2. Push in on the center of the outside edge of the filter and rotate up into the housing until it clips into position.
Page 169 Seats Fold-flat seatback Lift the handle and fold the seatback forward until it is flat. Note: For the bench seats, make sure the center safety belt is unbuckled before folding the seatback. Moving the seats backward and forward (if equipped) Second-Row Heated Seats (If Equipped) WARNING: Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord...
Page 170 Seats Note: Do not do the following: • Place heavy objects on the seat • Operate the seat heater if water or any other liquid is spilled on the seat. Allow the seat to dry thoroughly. The heated seats only operate when the ignition is on. To operate the heated seats: Press the button located on the rear of the floor console to cycle through the various heat settings and off.
Page 171 Seats Fold and tumble the second-row seat to access the third row: 1. Fold the outboard head restraint by pulling the head restraint release strap. 2. Lift the handle located on the side of the seat to fold the seatback flat. 3.
Page 172 Seats 4. To return the seat back to the floor from the tumbled position, rotate the seat down until you hear it latching to the floor. 5. Lift the seatback toward the rear of the vehicle, and rotate the seatback until you hear a click, locking it in the upright position.
Page 173 Seats Third-row seat access (power fold and tumble seat – if equipped) WARNING: Make sure that the seat is unoccupied when folding it down. Folding the seat while occupied could result in occupant injury or damage to the seat. Press and hold the control located at the back of the rear door opening to fold the seatback down and tumble the seat forward for access to the third row.
Page 174 Seats 1. Fold the outboard head restraint by pulling the head restraint release strap. 2. Pull on the strap located on the back of the second row seat. This will fold the seat back forward. Pull the strap a second time to tumble the seat forward, allowing easy exit from the third row seat.
Page 175 Seats 4. Lift the seatback toward the rear of the vehicle, and rotate the seatback until you hear a click, locking it in the upright position. Note: The seatback will not raise if the rear latch hooks are not properly engaged to the floor striker.
Page 176 Seats 3. From the rear of the vehicle, fold the seat back by pulling and holding the number 1 strap while pushing the seat back forward. Release the strap once the seat back starts rotating forward. 4. Release the cushion latches by pulling the number 2 strap while pulling on the strap located at the top of the seat back to tumble the seat all the way into the tub in the floor.
Page 177 Seats Unfolding the third row manual seat Note: Make sure that there are no objects such as books, purses or briefcases on the load floor before unstowing the seat. Failure to remove all objects from the top of the load floor prior to unstowing it may cause damage to the seat.
Page 178 Seats WARNING: Do not drive the vehicle when the third-row seat is rotated backwards. During a sudden stop, the safety belts are not functional in this position and the third-row seat can rapidly tip back to the forward position, all of which may result in serious injury. Note: Do not use seat in this position or damage to seat may occur.
Page 179 Seats These seats feature a power one-touch operation that allows you fold and stow the seats. • The power fold seats work only when the transmission is in park (P) and the liftgate is open. • If the ignition is off and the feature is still running, the battery saver will turn it off after 10 minutes.
Page 180: Universal Garage Door Opener (If Equipped)
Universal Garage Door Opener (If Equipped) 179 HOMELINK® WIRELESS CONTROL SYSTEM (IF EQUIPPED) WARNING: Make sure that the garage door and security device are free from obstruction when you are programming. Do not program the system with the vehicle in the garage. WARNING: Do not use the system with any garage door opener that does not have the safety stop and reverse feature as required by U.S.
Page 181 180 Universal Garage Door Opener (If Equipped) Programming Note: Put a new battery in the hand-held transmitter. This will ensure quicker training and accurate transmission of the radio-frequency signal. 1. With your vehicle parked outside of the garage and your key in the ignition, turn the key so that the ignition is in the on position.
Page 182 Universal Garage Door Opener (If Equipped) 181 After programming the HomeLink button, follow Steps 5 – 7 as listed below to program your garage door opener. Note: You may need a ladder to reach the unit and you may need to remove the cover or lamp lens on your garage door opener.
Page 183 182 Universal Garage Door Opener (If Equipped) Programming HomeLink to a Genie Intellicode 2 garage door opener Note: The Genie Intellicode 2 transmitter must already be programmed to operate with the garage door opener. Programing the transmitters To program HomeLink to the transmitter you must first put the transmitter into programming mode.
Page 184 Universal Garage Door Opener (If Equipped) 183 Programming HomeLink to the Genie Intellicode garage door opener motor Note: You may need a ladder to access the garage door opener motor. To program HomeLink to the garage door opener motor: 1. Press and hold the PROGRAM button on the garage door opener motor until both blue LED’s turn on.
Page 185: Auxiliary Power Points
Auxiliary Power Points AUXILIARY POWER POINTS WARNING: Do not plug optional electrical accessories into the cigarette lighter socket (if equipped). Improper use of the lighter can cause damage not covered by your warranty, and can result in fire or serious injury. Note: If used when the engine is not running, the battery will discharge.
Page 186 Auxiliary Power Points 110 Volt AC Power Point (If Equipped) WARNING: Do not keep electrical devices plugged in the power point whenever the device is not in use. Do not use any extension cord with the 110 volt AC power point, since it will defeat the safety protection design.
Page 187 Auxiliary Power Points The power point can switch to a fault mode when it is overloaded, overheated or shorted. Unplug your device and turn the ignition off then on for overloading and shorting conditions. Let the system cool off, then turn the ignition off then on for an overheating condition.
Page 188: Storage Compartments
Storage Compartments CENTER CONSOLE WARNING: Use only soft cups in the cupholder. Hard objects can injure you in a collision. Available console features include: A. USB and audio jack B. Power point (if equipped) C. Large cupholders with handle relief and individual grips D.
Page 189: Overhead Console
Storage Compartments OVERHEAD CONSOLE The appearance of the overhead console will vary according to your option package. Press near the rear edge of the door to open it. 2014 Explorer (exp) Owners Guide gf, 3rd Printing, September 2013 USA (fus)
Page 190: Starting And Stopping The Engine
Starting and Stopping the Engine GENERAL INFORMATION WARNING: Extended idling at high engine speeds can produce very high temperatures in the engine and exhaust system, creating the risk of fire or other damage. WARNING: Do not park, idle, or drive your vehicle on dry grass or other dry ground cover.
Page 191: Ignition Switch
Starting and Stopping the Engine IGNITION SWITCH (IF EQUIPPED) A. Off: The ignition is off. Note: When you switch the ignition off and leave your vehicle, do not leave your key in the ignition. This could cause your vehicle battery to lose charge.
Page 192 Starting and Stopping the Engine Ignition Modes ENGINE START STOP Off: Turns the ignition off. • Without applying the brake pedal, press and release the button once when the ignition is in the on mode, or when the engine is running but the vehicle is not in motion.
Page 193 Starting and Stopping the Engine Vehicles with an Ignition Key Note: Do not touch the accelerator pedal. 1. Fully press the brake pedal. 2. Turn the key to the start position. Release the key when the engine starts. Note: The engine may continue cranking for up to 15 seconds or until it starts.
Page 194 Starting and Stopping the Engine Fast Restart (Vehicles with Keyless Start) The fast restart feature allows you to restart the engine within 20 seconds of switching it off, even if a valid key is not present. Within 20 seconds of switching the engine off, press the brake pedal and press the button.
Page 195: Engine Block Heater
Starting and Stopping the Engine 2. If your vehicle has a keyless start system, move the transmission selector lever to position N and use the brakes to bring your vehicle to a safe stop. When your vehicle has stopped, move the transmission selector lever to position P and switch the ignition off by pressing and holding the button for one second, or pressing it three times within two seconds.
Page 196 Starting and Stopping the Engine We recommend that you do the following for safe and correct operation: • Use a 16-gauge outdoor extension cord that is product certified by Underwriter’s Laboratory or Canadian Standards Association. This extension cord must be suitable for use outdoors, in cold temperatures, and be clearly marked Suitable for Use with Outdoor Appliances.
Page 197: Fuel And Refueling
Fuel and Refueling SAFETY PRECAUTIONS WARNING: Do not overfill the fuel tank. The pressure in an overfilled tank may cause leakage and lead to fuel spray and fire. WARNING: The fuel system may be under pressure. If you hear a hissing sound near the fuel filler inlet, do not refuel until the sound stops.
Page 198: Fuel Quality
Fuel and Refueling • Avoid getting fuel liquid in your eyes. If fuel is splashed in the eyes, remove contact lenses (if worn), flush with water for 15 minutes and seek medical attention. Failure to seek proper medical attention could lead to permanent injury.
Page 199 Fuel and Refueling Choosing the Right Fuel With a Flex Fuel Vehicle (If Equipped) Use only UNLEADED gasoline or UNLEADED gasoline blended with a maximum of 85% ethanol (E-85) in your Flex Fuel Vehicle (FFV). If your vehicle is flex fuel capable, it will have a yellow bezel placed over the fuel fill inlet Do not use: •...
Page 200: Running Out Of Fuel
Fuel and Refueling RUNNING OUT OF FUEL Avoid running out of fuel because this situation may have an adverse effect on powertrain components. If you have run out of fuel: • You may need to cycle the ignition from off to on several times after refueling to allow the fuel system to pump the fuel from the tank to the engine.
Page 201: Refueling
Fuel and Refueling When filling the vehicle’s fuel tank from a portable fuel container, use the funnel included with the vehicle. 1. Locate the white plastic funnel in the spare tire compartment. 2. To open the fuel filler door, press the center of the rear edge and then release.
Page 202 Fuel and Refueling Use the following guidelines to avoid electrostatic charge build-up when filling an ungrounded fuel container: • Place approved fuel container on the ground. • DO NOT fill a fuel container while it is in the vehicle (including the cargo area).
Page 203 Fuel and Refueling 4. After you are done pumping fuel, slowly remove the fuel filler nozzle—allow about five to ten seconds after pumping fuel before removing the fuel filler nozzle. This allows residual fuel to drain back into the fuel tank and not spill onto the vehicle.
Page 204: Fuel Consumption
Fuel and Refueling FUEL CONSUMPTION Filling the Tank The advertised capacity is the indicated capacity and the empty reserve combined. Indicated capacity is the difference in the amount of fuel in a full tank and a tank when the fuel gauge indicates empty. Empty reserve is the amount of fuel in the tank after the fuel gauge indicates empty.
Page 205 Information are essential to the life and performance of your vehicle and to its emissions system. If other than Ford, Motorcraft® or Ford-authorized parts are used for maintenance replacements or for service of components affecting emission control, such non-Ford parts should be equivalent to genuine Ford Motor Company parts in performance and durability.
Page 206 Fuel and Refueling An improperly operating or damaged exhaust system may allow exhaust to enter the vehicle. Have a damaged or improperly operating exhaust system inspected and repaired immediately. Do not make any unauthorized changes to your vehicle or engine. By law, vehicle owners and anyone who manufactures, repairs, services, sells, leases, trades vehicles, or supervises a fleet of vehicles are not permitted to intentionally remove an emission control device or prevent...
Page 207 Fuel and Refueling If the service engine soon indicator remains on, have your vehicle serviced at the first available opportunity. Although some malfunctions detected by the OBD-II may not have symptoms that are apparent, continued driving with the service engine soon indicator on can result in increased emissions, lower fuel economy, reduced engine and transmission smoothness, and can lead to more costly repairs.
Page 208: Transmission
Transmission AUTOMATIC TRANSMISSION WARNING: Always set the parking brake fully and make sure the gearshift is latched in P (Park). Turn the ignition to the off position and remove the key whenever you leave your vehicle. WARNING: Do not use the tow feature when driving in icy or slippery conditions as the increased engine braking can cause the rear wheels to slide and the vehicle to swing around with the possible loss of vehicle control.
Page 209 Transmission D (Drive) with Overdrive The normal driving position for the best fuel economy. Transmission operates in gears one through six. The automatic transmission shift strategy has the ability to detect hilly terrain or mountainous areas and will provide a limited amount of grade assist features automatically.
Page 210 Transmission Grade assist: • Provides additional grade (engine) braking and extends lower gear operation on uphill climbs for hilly terrain or mountainous areas. • Provides additional engine braking through the automatic transmission shift strategy which reacts to vehicle inputs (vehicle acceleration, accelerator pedal, brake pedal and vehicle speed).
Page 211 Transmission SelectShift Automatic® Transmission Your SelectShift automatic transmission gives you the ability to manually change gears if you’d like. To use SelectShift, move the gearshift lever into M (Manual). Now you can use select shift to manually change gears. If your vehicle is equipped with (+)/(–) buttons on the side of your gearshift lever: •...
Page 212 Transmission Upshift to the recommended shift speeds according to the following chart. Upshifts when accelerating (recommended for best fuel economy) Shift from: 1 - 2 15 mph (24 km/h) 2 - 3 25 mph (40 km/h) 3 - 4 40 mph (64 km/h) 4 - 5 45 mph (72 km/h) 5 - 6...
Page 213 Transmission Apply the parking brake, turn the ignition key to the off position, and remove the key. 1. Using a screwdriver (or similar tool), carefully pry off and remove the Brake shift interlock access panel. 2. Locate the brake shift interlock lever in front of the shifter assembly.
Page 214: Hill Start Assist
Transmission If Your Vehicle Gets Stuck in Mud or Snow Note: Do not rock the vehicle if the engine is not at normal operating temperature or damage to the transmission may occur. Note: Do not rock the vehicle for more than a minute or damage to the transmission and tires may occur, or the engine may overheat.
Page 215 Transmission Using Hill Start Assist 1. Press the brake pedal to bring the vehicle to a complete standstill. Keep the brake pedal pressed. 2. If the sensors detect that the vehicle is on a slope, the hill start assist feature will be activated automatically. 3.
Page 216: Four-Wheel Drive (If Equipped)
Four-Wheel Drive (If Equipped) USING YOUR FOUR WHEEL DRIVE (4WD) SYSTEM The intelligent 4WD system continuously monitors vehicle conditions and automatically adjusts the power distribution between the front and rear wheels. It combines transparent all-surface operation with highly capable four-wheel drive. The 4WD system is always active and requires no driver input.
Page 217: Steering Wheel Controls
Four-Wheel Drive (If Equipped) How Utility Vehicles Differ from Other Vehicles Truck and utility vehicles can differ from some other vehicles. Your vehicle may be higher to allow it to travel over rough terrain without getting hung up or damaging underbody components. The differences that make your vehicle so versatile also make it handle differently than an ordinary passenger car.
Page 218 Four-Wheel Drive (If Equipped) If your vehicle goes off the edge of the pavement WARNING: Vehicles with a higher center of gravity such as utility and four-wheel drive vehicles handle differently than vehicles with a lower center of gravity. Utility and four-wheel drive vehicles are not designed for cornering at speeds as high as passenger cars any more than low-slung sports cars are designed to perform satisfactorily under off-road conditions.
Page 219 Four-Wheel Drive (If Equipped) If your vehicle gets stuck in mud or snow it may be rocked out by shifting between forward and reverse gears, stopping between shifts, in a steady pattern. Press lightly on the accelerator in each gear. Note: Do not rock the vehicle if the engine is not at normal operating temperature or damage to the transmission may occur.
Page 220 Four-Wheel Drive (If Equipped) Sand When driving over sand, try to keep all four wheels on the most solid area of the trail. Avoid reducing the tire pressures but shift to a lower gear and drive steadily through the terrain. Apply the accelerator slowly and avoid spinning the wheels.
Page 221 Ford Motor Company joins the U.S. Forest Service and the Bureau of Land Management in encouraging you to help preserve our national forest and other public and private lands by “treading lightly.”...
Page 222 Four-Wheel Drive (If Equipped) Driving on snow and ice WARNING: If you are driving in slippery conditions that require tire chains or cables, then it is critical that you drive cautiously. Keep speeds down, allow for longer stopping distances and avoid aggressive steering to reduce the chances of a loss of vehicle control which can lead to serious injury or death.
Page 223 Ford Motor Company recommends that caution be used with any vehicle equipped with a high load or device (such as ladder racks or pickup box cover).
Page 224: Brakes
Brakes GENERAL INFORMATION Note: Occasional brake noise is normal. If a metal-to-metal, continuous grinding or continuous squeal sound is present, the brake linings may be worn out. Have them inspected by an authorized dealer. If your vehicle has continuous vibration or shudder in the steering wheel while braking, have your vehicle inspected by an authorized dealer.
Page 225: Hints On Driving With Anti-Lock Brakes
Brakes Anti-Lock Brake System This system helps you maintain steering control during emergency stops by keeping the brakes from locking. This lamp momentarily illuminates when you turn the ignition on. If the light does not illuminate during start-up, remains on or flashes, the anti-lock brake system may be disabled and may need to be serviced.
Page 226: Traction Control
Traction Control PRINCIPLES OF OPERATION The traction control system helps avoid drive wheel spin and loss of traction. If your vehicle begins to slide, the system applies the brakes to individual wheels and, when needed, reduces engine power at the same time. If the wheels spin when accelerating on slippery or loose surfaces, the system reduces engine power in order to increase traction.
Page 227: Stability Control
Stability Control PRINCIPLES OF OPERATION WARNING: Vehicle modifications involving braking system, aftermarket roof racks, suspension, steering system, tire construction and wheel or tire size may change the handling characteristics of the vehicle and may adversely affect the performance of the AdvanceTrac® system. In addition, installing any stereo loudspeakers may interfere with and adversely affect the AdvanceTrac®...
Page 228: Advancetrac
Stability Control A Vehicle without AdvanceTrac® with RSC® skidding off its intended route. B Vehicle with AdvanceTrac® with RSC® maintaining control on a slippery surface. USING ADVANCETRAC® WITH RSC® The system automatically activates when you start your engine. The AdvanceTrac® with RSC® system cannot be completely turned off, but the electronic stability control and roll stability control portions of the system are disabled when the transmission is in reverse (R).
Page 229: Terrain Response
Terrain Response TERRAIN MANAGEMENT (IF EQUIPPED) This system optimizes drivability and comfort as well as maximizing traction while operating on different types of terrain. Turn the control located on the center console to choose between the following modes: 1. Grass/Gravel/Snow mode should be selected where a firm surface is covered with loose or slippery material such as packed snow, ice, water, grass, or a thin layer of gravel or sand.
Page 230: Hill Descent Control
Terrain Response If the system becomes inoperable, selecting some modes may not be possible and a message is displayed. If it becomes inoperable due to a system malfunction, all of the mode indicators on the control turn off and one of the following messages appears in the information display: TERRAIN MANAGEMENT SYSTEM FAULT: Cycling the key may clear the fault.
Page 231 Terrain Response To enable hill descent control and set the descent speed, do the following: 1. Press and release the hill descent button located in the center of the terrain management control. A light in the control will illuminate and chime will sound when this feature is activated.
Page 232: Parking Aids
Parking Aids SENSING SYSTEM (IF EQUIPPED) WARNING: To help avoid personal injury, please read and understand the limitations of the system as contained in this section. Sensing is only an aid for some (generally large and fixed) objects when moving in reverse on a flat surface at parking speeds. Traffic control systems, inclement weather, air brakes, and external motors and fans may also affect the function of the sensing system;...
Page 233 Parking Aids If a fault is present in the system, a warning message appears in the information display and does not allow the driver to switch the faulted system on. Note: If your vehicle is equipped with MyKey®, it is possible to prevent turning the sensing system off.
Page 234: Active Park Assist
Parking Aids ACTIVE PARK ASSIST (IF EQUIPPED) WARNING: This system is designed to be a supplementary park aid. It may not work in all conditions and is not intended to replace the driver’s attention and judgment. The driver is responsible for avoiding hazards and maintaining a safe distance and speed, even when the system is in use.
Page 235 Parking Aids Using Active Park Assist Press the button; the touch screen displays a message and a AUTO corresponding graphic to indicate it’s searching for a parking space. Use the turn signal to indicate which side of the vehicle you want the system to search on.
Page 236 Parking Aids Automatic Steering into Parking Space Note: If vehicle speed exceeds 6 mph (10 km/h), the system turns off and you need to take full control of the vehicle. Note: If a maneuver is interrupted before completion, the system turns off and you need to full take control of the vehicle.
Page 237 Parking Aids Deactivating the Park Assist Feature The system can be deactivated manually by: • pressing the active park assist button • grabbing the steering wheel • driving above approximately 20 mph (35 km/h) for 30 seconds during an active park search •...
Page 238: Rear-View Camera System
Parking Aids The system does not position the vehicle where I want in the space The vehicle is rolling in the opposite direction of the transmission (i.e. rolling forward when R [Reverse] is selected) The transmission is in R (Reverse); the vehicle must be moving forward to detect a parking space An irregular curb along the parking space prevents the system from aligning the vehicle properly...
Page 239 Parking Aids WARNING: Use caution when using the rear video camera and the liftgate is ajar. If the liftgate is ajar, the camera will be out of position and the video image may be incorrect. All guidelines have been removed when the liftgate is ajar. WARNING: Use caution when turning camera features on or off while in R (Reverse).
Page 240 Parking Aids Note: If the transmission is in R (Reverse) and the trunk/liftgate is ajar, no rear view camera features are displayed. Note: If the image comes on while the transmission is not in R (Reverse), have the system inspected by your authorized dealer. Note: When towing, the camera only sees what is being towed behind the vehicle.
Page 241 Parking Aids Guidelines and the Centerline Note: Fixed guidelines and active guidelines (if equipped) are only available when the transmission is in R (Reverse). A. Active guidelines (if equipped) B. Centerline C. Fixed guideline: Green zone D. Fixed guideline: Yellow zone E.
Page 242 Parking Aids Enhanced Park Aids Note: Enhanced park aids is only available when the transmission is in R (Reverse). Note: The reverse sensing system is not effective at speeds above 3 mph (5 km/h) and may not detect certain angular or moving objects. The enhanced park aids allows the driver to view the area that is being detected by the reverse sensing system.
Page 243: Cruise Control
Cruise Control PRINCIPLES OF OPERATION Cruise control lets you maintain a set speed without keeping your foot on the accelerator pedal. USING CRUISE CONTROL WARNING: Do not use cruise control in heavy traffic, on winding roads or when the road surface is slippery. This could result in loss of vehicle control, serious injury or death.
Page 244: Using Adaptive Cruise Control
Cruise Control Setting a Speed 1. Accelerate to the desired speed. 2. Press the SET control upward and release. 3. Take your foot off the accelerator pedal. The indicator will change colors in the instrument cluster. Changing the Set Speed Note: If you accelerate by pressing the accelerator pedal, the set speed will not change.
Page 245 Cruise Control WARNING: Adaptive cruise control is not a collision warning or avoidance system. Additionally, adaptive cruise control will not detect: • stationary or slow moving vehicles below 6 mph (10 km/h) • pedestrians or objects in the roadway • oncoming vehicles in the same lane. WARNING: Do not use the adaptive cruise control when entering or leaving a highway, in heavy traffic or on roads that are winding, slippery or unpaved.
Page 246 Cruise Control Setting Adaptive Cruise Control 1. Press and release ON. The information display will show the gray indicator light, current gap setting and SET. The system is set to standby mode. 2. Accelerate to the desired speed. 3. Press SET upward and release. The vehicle speed is stored in the memory.
Page 247 Cruise Control When a vehicle ahead of you enters the same lane or a slower vehicle is ahead in the same lane, the vehicle speed adjusts to maintain a preset gap distance. The distance setting is adjustable. The lead vehicle graphic will be illuminated. Your vehicle will maintain a constant distance between the vehicle ahead until: •...
Page 248 Cruise Control Graphic display Following Following Dynamic (bars between distance distance at behavior vehicles) 60 mph (100 km/h) 1 bar 1 second 31 yards (28 m) Sporty 2 bars 1.4 seconds 43 yards (39 m) Normal 3 bars 1.8 seconds 55 yards (50 m) Normal 4 bars 2.2 seconds...
Page 249 Cruise Control The system may apply the brakes to slow your vehicle down to the new set speed. The set speed will display continuously in the information display while the system is active. Resuming the Set Speed Note: Resume should only be used if you are aware of the set speed and intend to return to it.
Page 250 Cruise Control Detection Issues The radar sensor has a limited field of vision. It may not detect vehicles at all or detect a vehicle later than expected in some situations. The lead vehicle graphic will not illuminate if the system does not detect a vehicle in front of you.
Page 251 Cruise Control Blocked Sensor WARNING: Do not use ACC when towing a trailer with brake controls. Aftermarket trailer brakes will not function properly when ACC is activated because the brakes are electronically controlled. Failing to do so may result in loss of vehicle control, which could result in serious injury.
Page 252 Cruise Control Cause Action Swirling water, or snow or ice on Do not use system in these the surface of the road may conditions because it may not interfere with the radar signals. detect any vehicle ahead. You are in a desert or remote area Wait a short time or switch to with no other vehicles and no normal cruise control.
Page 253: Driving Aids
Driving Aids DRIVER ALERT (IF EQUIPPED) WARNING: The driver alert system is designed to aid you. It is not intended to replace your attention and judgment. You are still responsible to drive with due care and attention. Note: The system will store the on/off setting in the information display menu through ignition cycles.
Page 254 Driving Aids System Display When active the system will run automatically in the background and only issue a warning if required. You can view the status at any time using the information display. Refer to the Information Displays chapter. The alertness level is shown by six steps in a colored bar. The current assessment of your alertness is within a typical range.
Page 255: Lane Keeping System
Driving Aids LANE KEEPING SYSTEM (IF EQUIPPED) WARNING: The system is designed to aid the driver. It is not intended to replace the driver’s attention and judgment. The driver is still responsible to drive with due care and attention. The system detects unintentional drifting toward the outside of the lane and alerts and/or aids the driver to stay in the lane through the steering system and instrument cluster display.
Page 256 Driving Aids System Settings The system has one standard feature setting and one optional setting menu available. To view or adjust the settings, refer to the Information Displays chapter. The last-known selection for each of these settings is stored by the system. You do not need to readjust your settings each time you turn on the system.
Page 257 Driving Aids Intensity: This setting affects the intensity of the steering wheel vibration used for the alert mode. This setting does not impact the aid mode. • Low • Medium • High System Display When you switch the system on, an overhead graphic of a vehicle with lane markings will be displayed in the left instrument cluster display.
Page 258 Driving Aids The system can be temporarily disabled at any time by the following: • Quick braking • Fast acceleration • Using the turn signal indicator • Evasive steering maneuver Troubleshooting Why is the feature not available (line markings are gray) when I can see the lane markings on the road? Vehicle speed is outside the operational range of the feature Sun is shining directly into the camera lens...
Page 259: Alert (Cta)
Driving Aids Why does the vehicle not come back into the middle of the lane always, as expected, in the Aid or Aid + Alert mode? High cross winds Large road crown Rough roads, grooves, shoulder drop-offs Heavy uneven loading of the vehicle or improper tire inflation pressure If the tires have been exchanged (including snow tires), or the suspension has been modified BLIND SPOT INFORMATION SYSTEM (BLIS®) WITH CROSS...
Page 260 Driving Aids CTA warns the driver of vehicles approaching from the sides when the transmission is in R (Reverse). Note: BLIS® is not designed to prevent contact with other vehicles or objects; or to detect parked vehicles, people, animals or infrastructure (fences, guardrails, trees, etc.).
Page 261 Driving Aids In this first example, the left sensor is only partially obstructed; zone coverage is nearly maximized. Zone coverage also decreases when parking at shallow angles. Here, the left sensor is mostly obstructed; zone coverage on that side is severely limited. 2014 Explorer (exp) Owners Guide gf, 3rd Printing, September 2013 USA (fus)
Page 262 Driving Aids System Lights and Messages The BLIS® and CTA systems illuminate a yellow alert indicator in the outside mirror on the side of the vehicle the approaching vehicle is coming from. Note: The alert indicator dims when nighttime darkness is detected. CTA also sounds an audible alarm and a message appears in the information display indicating a vehicle is coming from the right or left.
Page 263 Driving Aids If the system detects a degraded performance condition, a blocked sensor warning or low visibility warning will appear in the information display and the alert indicator illuminates in the appropriate mirror(s). The information display warning can be cleared but the alert indicator remains illuminated.
Page 264 Driving Aids False Alerts Note: If you connected a trailer to your vehicle the BLIS® system may detect the trailer causing a false alert. To avoid false alerts you may want to turn the BLIS off manually. There may be certain instances when either the BLIS® or CTA systems illuminate the alert indicator with no vehicle in the coverage zone;...
Page 265: Collision Warning System
Driving Aids COLLISION WARNING SYSTEM (IF EQUIPPED) WARNING: This system is designed to be a supplementary driving aid. It is not intended to replace the driver’s attention, and judgment, or the need to apply the brakes. This system does NOT activate the brakes automatically.
Page 266 Driving Aids Using the Collision Warning System WARNING: The collision warning system’s brake support can only help reduce the speed at which a collision occurs if the driver applies the vehicle’s brakes. The brake pedal must be pressed just like any typical braking situation. The warning system sensitivity can be adjusted to one of three possible settings by using the information display control.
Page 267 Driving Aids Cause Action Heavy rain, spray, snow, or fog is The collision warning system is interfering with the radar signals temporarily disabled. Collision warning should automatically reactivate a short time after the weather conditions improve. Swirling water, or snow or ice on The collision warning system is the surface of the road may temporarily disabled.
Page 268: Steering
Driving Aids If the front end of the vehicle is hit or damaged, the radar sensing zone may be altered causing missed or false collision warnings. See your authorized dealer to have your collision warning radar checked for proper coverage and operation. STEERING Electric Power Steering WARNING: The electric power steering system has diagnostic...
Page 269 Driving Aids If your vehicle loses electrical power while you are driving (or if the ignition is turned off), you can steer the vehicle manually, but it takes more effort. Extreme continuous steering may increase the effort it takes for you to steer. This occurs to prevent internal overheating and permanent damage to your steering system.
Page 270: Load Carrying
Load Carrying CARGO NETS (IF EQUIPPED) WARNING: This net is not designed to restrain objects during a collision or heavy braking. The cargo net secures lightweight objects in the cargo area. Attach the net to the loops and anchors provided. ROOF RACKS AND LOAD CARRIERS (IF EQUIPPED) WARNING: When loading the roof racks, we recommend you evenly distribute the load, as well as maintain a low center of...
Page 271: Vehicle Loading
Load Carrying For correct roof rack system function, you must place loads directly on crossbars affixed to the roof rack side rails. We recommend you use Ford Genuine Accessory crossbars designed specifically for your vehicle. Make sure that you securely fasten the load. Check the tightness of the load before driving and at each fuel stop.
Page 272 Load Carrying Vehicle Curb Weight – is the weight of your new vehicle when you picked it up from your authorized dealer plus any aftermarket equipment. Payload – is the combined weight of cargo and passengers that the vehicle is carrying. The maximum payload for your vehicle can be found on the Tire Label on the B-Pillar or the edge of the driver’s door (vehicles exported outside the US and Canada may not have a Tire Label).
Page 273 Load Carrying Example only: Cargo Weight – includes all weight added to the Base Curb Weight, including cargo and optional equipment. When towing, trailer tongue load or king pin weight is also part of cargo weight. GAW (Gross Axle Weight) – is the total weight placed on each axle (front and rear) –...
Page 274 Load Carrying GAWR (Gross Axle Weight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance Certification Label. The label shall be affixed to either the door hinge pillar, door-latch post, or the door edge that meets the door-latch post, next to the driver’s seating position.
Page 275 Load Carrying • Example only: WARNING: Exceeding the Safety Compliance Certification Label vehicle weight rating limits could result in substandard vehicle handling or performance, engine, transmission and/or structural damage, serious damage to the vehicle, loss of control and personal injury. 2014 Explorer (exp) Owners Guide gf, 3rd Printing, September 2013 USA (fus)
Page 276 Load Carrying GCW (Gross Combined Weight) – is the weight of the loaded vehicle (GVW) plus the weight of the fully loaded trailer. GCWR (Gross Combined Weight Rating) – is the maximum allowable weight of the vehicle and the loaded trailer – including all cargo and passengers –...
Page 277 Load Carrying WARNING: Exceeding any vehicle weight rating limitation could result in serious damage to the vehicle and/or personal injury. Steps for determining the correct load limit: 1. Locate the statement “The combined weight of occupants and cargo should never exceed XXX kg or XXX lb.” on your vehicle’s placard. 2.
Page 278 Load Carrying • Suppose your vehicle has a 1400 lb. (635 kg) cargo and luggage capacity. You and one of your friends decide to pick up cement from the local home improvement store to finish that patio you have been planning for the past 2 years.
Page 279: Towing
Towing TOWING A TRAILER WARNING: Do not exceed the GVWR or the GAWR specified on the certification label. WARNING: Towing trailers beyond the maximum recommended gross trailer weight exceeds the limit of your vehicle and could result in engine damage, transmission damage, structural damage, loss of vehicle control, vehicle rollover and personal injury.
Page 280 TRAILER SWAY CONTROL (IF EQUIPPED) WARNING: Turning off trailer sway control increases the risk of loss of vehicle control, serious injury or death. Ford does not recommend disabling this feature except in situations where speed reduction may be detrimental (such as hill climbing), the driver has significant trailer towing experience, and can control trailer sway and maintain safe operation.
Page 281 Towing Your vehicle may tow a Class I or III trailer provided the maximum trailer weight is less than or equal to the maximum trailer weight listed for your vehicle configuration on the following chart. Engine and trailer Maximum GCWR Maximum trailer class weight...
Page 282 Towing Trailer Towing Connector (Vehicles with a Trailer Towing Package and 7–Pin Connector) When attaching the trailer wiring connector to your vehicle, only use a proper fitting connector that works with the vehicle and trailer functions. If your vehicle has a trailer towing package, it may have a 7–pin connector.
Page 283 Towing 2. To reinstall the cover, insert the four plastic tabs on top of the cover into the corresponding slots (B), and push the cover into the bumper trim. 3. Hold the cover against the bumper trim and reinstall the two ⁄...
Page 284 Towing Safety Chains Note: Never attach safety chains to the bumper. Always connect the safety chains to the hook retainers of your vehicle hitch. To connect the safety chains, cross them under the trailer tongue and allow enough slack for turning tight corners. Do not allow the chains to drag on the ground.
Page 285 Towing When Towing a Trailer • Do not drive faster than 70 mph (113 km/h) during the first 500 miles (800 kilometers). • Do not make full-throttle starts. • Check your hitch, electrical connections and trailer wheel lug nuts thoroughly after you have traveled 50 miles (80 kilometers). •...
Page 286 We recommend the use of a wheel lift and dollies or flatbed equipment to tow your vehicle. Do not tow with a slingbelt. Ford Motor Company has not approved a slingbelt towing procedure. Vehicle damage may occur if towed incorrectly, or by any other means.
Page 287: Recreational Towing
Towing Front-wheel drive vehicles must have the front wheels placed on a tow dolly when towing your vehicle from the rear using wheel lift equipment. This prevents damage to the transmission. Towing an all-wheel drive vehicle requires that all wheels be off the ground, such as using a wheel lift and dollies or flatbed equipment.
Page 288 Towing Vehicles Equipped with a 3.5L or 3.7L Engine Note: Put your climate control system in recirculated air mode to prevent exhaust fumes from entering your vehicle. See the Climate Control chapter. Follow these guidelines if you have a need for recreational towing, such as towing your vehicle behind a motorhome or truck.
Page 289: Driving Hints
Driving Hints BREAKING-IN You need to break in new tires for approximately 300 miles (480 kilometers). During this time, your vehicle may exhibit some unique driving characteristics. Avoid driving too fast during the first 1000 miles (1600 kilometers). Vary your speed frequently and change up through the gears early.
Page 290 Driving Hints • Carry unnecessary weight (approximately 1 mpg [0.4 km/L] is lost for every 400 pounds [180 kilograms] of weight carried). • Add particular accessories to your vehicle (e.g.; bug deflectors, rollbars or light bars, running boards, ski racks). •...
Page 291: Floor Mats
Driving Hints FLOOR MATS WARNING: Always use floor mats that are designed to fit the foot well of your vehicle, leaving the pedal area unobstructed, and which can be firmly secured to retention posts so that they cannot slip out of position and interfere with the pedals or impair safe operation of your vehicle in other ways.
Page 292: Roadside Emergencies
• Winch out – available within 100 feet (30.5 meters) of a paved or county maintained road, no recoveries. • Towing – Ford eligible vehicles will be towed to an authorized dealer within 35 miles (56.3 kilometers) of the disablement location or to the nearest authorized dealer.
Page 293: Hazard Warning Flashers
1-800-241-3673. If you need to arrange roadside assistance for yourself, Ford Motor Company will reimburse a reasonable amount for towing to the nearest Ford dealership within 35 miles (56.3 kilometers). To obtain reimbursement information, United States Ford vehicle customers call 1-800-241-3673. Customers will be asked to submit their original receipts.
Page 294 WARNING: Failure to inspect and if necessary repair fuel leaks after a collision may increase the risk of fire and serious injury. Ford Motor Company recommends that the fuel system be inspected by an authorized dealer after any collision. In the event of a moderate to severe collision, this vehicle includes a fuel pump shutoff feature that stops the flow of fuel to the engine.
Page 295: Jump-Starting The Vehicle
Roadside Emergencies JUMP-STARTING THE VEHICLE WARNING: The gases around the battery can explode if exposed to flames, sparks, or lit cigarettes. An explosion could result in injury or vehicle damage. WARNING: Batteries contain sulfuric acid which can burn skin, eyes and clothing, if contacted. Do not attempt to push-start your automatic transmission vehicle.
Page 296 Roadside Emergencies Connecting the Jumper Cables WARNING: Do not connect the end of the second cable to the negative (-) terminal of the battery to be jumped. A spark may cause an explosion of the gases that surround the battery. Note: Do not attach the negative (-) cable to fuel lines, engine rocker covers, the intake manifold or electrical components as grounding points.
Page 297 Roadside Emergencies Removing the Jumper Cables Note: In the illustration, the vehicle on the bottom is used to designate the assisting (boosting) battery. Remove the jumper cables in the reverse order that they were connected. 1. Remove the jumper cable from the ground metal surface.
Page 298: Customer Assistance
A reasonable time must be allowed to perform a repair after taking your vehicle to the authorized dealer. Repairs will be made using Ford or Motorcraft parts, or remanufactured or other parts that are authorized by Ford.
Page 299 • The name of the authorized dealer and city where located • The vehicle’s current odometer reading. In some states, you must directly notify Ford in writing before pursuing remedies under your state’s warranty laws. Ford is also allowed a final repair attempt in some states.
Page 300 In the case of 1 or 2 above, the consumer must also notify the manufacturer of the need for the repair of the nonconformity at the following address: Ford Motor Company 16800 Executive Plaza Drive Mail Drop 3NE-B Dearborn, MI 48126...
Page 301 BBB Auto Line dispute, and decision, are admissible in the court action. Should you choose to accept the BBB AUTO LINE decision, Ford is then bound by the decision, and must comply with the decision within 30 days of receipt of your acceptance letter.
Page 302 (CANADA ONLY) This pertains to vehicles delivered to authorized Canadian dealers. In those cases, where you continue to feel that the efforts by Ford of Canada and the authorized dealer to resolve a factory-related vehicle service concern have been unsatisfactory, Ford of Canada participates in an impartial third party mediation or arbitration program administered by the Canadian Motor Vehicle Arbitration Plan (CAMVAP).
Page 303 Central America, the Caribbean, and Israel, contact the nearest authorized dealer. If the authorized dealer cannot help you, contact: FORD MOTOR COMPANY FORD EXPORT OPERATIONS & GLOBAL INITIATIVES Customer Relationship Center 1555 Fairlane Drive Fairlane Business Park #3 Allen Park, Michigan 48101 U.S.A.
Page 304 If you buy your vehicle in North America and then relocate to any of the above locations, register your vehicle identification number (VIN) and new address with Ford Motor Company Export Operations & Global Growth Initiatives by emailing expcac@ford.com. If you are in another foreign country, contact the nearest authorized dealer.
Page 305: Reporting Safety Defects (U.s. Only)
However, NHTSA cannot become involved in individual problems between you, your dealer, or Ford Motor Company. To contact NHTSA, you may call the Vehicle Safety Hotline toll-free at 1–888–327–4236 (TTY: 1–800–424–9153);...
Page 306: Fuses
Fuses CHANGING A FUSE Fuses WARNING: Always replace a fuse with one that has the specified amperage rating. Using a fuse with a higher amperage rating can cause severe wire damage and could start a fire. If electrical components in your vehicle are not working, a fuse may have blown.
Page 307: Fuse Specification Chart
Fuses FUSE SPECIFICATION CHART Power Distribution Box WARNING: Always disconnect the battery before servicing high current fuses. WARNING: To reduce risk of electrical shock, always replace the cover to the power distribution box before reconnecting the battery or refilling fluid reservoirs. The power distribution box is located in the engine compartment.
Page 308 Fuses Fuse or relay Fuse amp Protected components number rating 30A** Wipers, Front washer 50A** Anti-lock brake system pump — Not used 30A** Power liftgate 20A** Moonroof 20A** Power point #2 (console rear) — 3rd row rear seat release relay —...
Page 309 Fuses Fuse or relay Fuse amp Protected components number rating 40A** Engine cooling fan #2 high speed fuse 25A** Engine cooling fan #1 and #2 low speed secondary fuse — Auxiliary blower motor relay — Engine cooling fan #1 and #2 low speed relay #2 —...
Page 310 Fuses Fuse or relay Fuse amp Protected components number rating — Wiper relay 15A* Transmission control module 20A* Left high-intensity discharge headlamps 10A* Alternator sensor 10A* Brake on/off switch 10A* Trailer tow back-up lamps 20A* Second row seat release 10A* Air conditioning clutch 15A* Trailer tow stop/turn lamps...
Page 311 Fuses Fuse or relay Fuse amp Protected components number rating — Not used — Not used 15A* Rear washer — Not used 20A* Trailer tow park lamps — Not used 7.5A* Powertrain control module keep-alive power, Powertrain control module relay, Canister vent solenoid Run/start relay coil —...
Page 312 Fuses Passenger Compartment Fuse Panel The fuse panel is located below and to the left of the steering wheel by the brake pedal. Remove the panel cover to access the fuses. To remove a fuse use the fuse puller tool provided on the fuse panel cover.
Page 313 Fuses Fuse or relay Fuse amp Protected components number rating Amplifier Not used (spare) 7.5A Memory seat module logic feed Not used (spare) 4-inch radio display, Power liftgate logic, Electronic finish panel, SYNC Run/accessory relay (wipers, rear washer), Rain sensor Instrument cluster, Heads-up display Interior courtesy lamps (overhead...
Page 314 Fuses Fuse or relay Fuse amp Protected components number rating Horn relay Steering wheel control module, Intelligent access, Headlamp switch Datalink connector, Steering wheel control module Liftgate release Radio frequency module Intelligent access module Ignition switch, Push-button start switch Radio, Global positioning system module Front park lamps Trailer tow brake controller...
Page 315 Fuses Fuse or relay Fuse amp Protected components number rating Auto-dimming rearview mirror, Moonroof High beam headlamp shutters Rear park lamps, License plate lamps, Trailer tow park lamps 7.5A Overdrive cancel, Tow/haul Not used (spare) Not used (spare) Not used (spare) Not used (spare) Climate control module Fog lamps, left and right turn...
Page 316: Maintenance
GENERAL INFORMATION Have your vehicle serviced regularly to help maintain its roadworthiness and resale value. There is a large network of Ford authorized dealers who are there to help you with their professional servicing expertise. We believe that their specially trained technicians are best qualified to service your vehicle properly and expertly.
Page 317: Opening And Closing The Hood
Maintenance OPENING AND CLOSING THE HOOD 1. Inside the vehicle, pull the hood release handle located under the bottom left corner of the instrument panel. 2. Go to the front of the vehicle and release the auxiliary latch that is located under the front center of the hood.
Page 318: Under Hood Overview
Maintenance UNDER HOOD OVERVIEW 2.0L EcoBoost® Engine A. Engine coolant reservoir B. Brake fluid reservoir C. Battery D. Power distribution box E. Air filter assembly F. Engine oil filler cap G. Engine oil dipstick H. Windshield washer fluid reservoir 2014 Explorer (exp) Owners Guide gf, 3rd Printing, September 2013 USA (fus)
Page 319 Maintenance 3.5L V6 Engine A. Engine coolant reservoir B. Brake fluid reservoir C. Battery D. Power distribution box E. Air filter assembly F. Transmission fluid dipstick (out of view) G. Engine oil dipstick H. Engine oil filler cap I. Windshield washer fluid reservoir 2014 Explorer (exp) Owners Guide gf, 3rd Printing, September 2013 USA (fus)
Page 320 Maintenance 3.5L V6 EcoBoost® Engine A. Engine coolant reservoir B. Brake fluid reservoir C. Battery D. Power distribution box E. Air filter assembly F. Automatic transmission fluid dipstick (out of view) G. Engine oil dipstick H. Engine oil filler cap I.
Page 321: Engine Oil Dipstick
Maintenance Engine shield Some vehicles may be equipped with an aero-shield under the engine. This shield needs to be removed for service, including oil and filter changes. It is secured with four quick release fasteners. ENGINE OIL DIPSTICK A. – MIN B.
Page 322: Engine Coolant Check
Note: For best results, coolant concentration should be tested with a refractometer such as Rotunda tool 300-ROB75240 available from your dealer. Ford does not recommend the use of hydrometers or coolant test strips for measuring coolant concentration. Note: Automotive fluids are not interchangeable; do not use engine coolant/antifreeze or windshield washer fluid outside of its specified function and vehicle location.
Page 323 Maintenance Adding Engine Coolant WARNING: Do not add engine coolant when the engine is hot. Steam and scalding liquids released from a hot cooling system can burn you badly. Also, you can be burned if you spill coolant on hot engine parts.
Page 324 Severe Climates If you drive in extremely cold climates: • It may be necessary to have a Ford authorized dealer increase the coolant concentration above 50%. • A coolant concentration of 60% will provide improved freeze point protection.
Page 325 Maintenance Vehicles driven year-round in non-extreme climates should use prediluted engine coolant for optimum cooling system and engine protection. Engine Fluid Temperature Management (If Equipped) WARNING: To reduce the risk of collision and injury, be prepared that the vehicle speed may reduce and the vehicle may not be able to accelerate with full power until the fluid temperatures reduce.
Page 326 Maintenance 3. Turn the engine off and wait for it to cool before checking the coolant level. WARNING: Never remove the coolant reservoir cap while the engine is running or hot. 4. If the coolant level is normal, you may restart your engine and continue on.
Page 327 Maintenance When Fail-Safe Mode is Activated WARNING: Fail-safe mode is for use during emergencies only. Operate the vehicle in fail-safe mode only as long as necessary to bring the vehicle to rest in a safe location and seek immediate repairs. When in fail-safe mode, the vehicle will have limited power, will not be able to maintain high-speed operation, and may completely shut down without warning, potentially losing engine power, power steering assist,...
Page 328 Maintenance Do not use supplemental transmission fluid additives, treatments or cleaning agents. The use of these materials may affect transmission operation and result in damage to internal transmission components. 6F50/6F55 Transmission WARNING: The dipstick cap and surrounding components may be hot; gloves are recommended. WARNING: Use gloves when moving the air filter assembly;...
Page 329 Maintenance Moving the Air Filter Assembly (EcoBoost engine) WARNING: Do not run engine with the air filter disconnected. 1. Shut the engine off. 2. Clean the area around the clamp that connects the air filter assembly to the rubber hose (1). 3.
Page 330 Maintenance 7. Without disconnecting the sensor (4), pull the air filter assembly up to disconnect the air filter assembly from the seated grommets located underneath the air filter assembly. 8. Rotate the air filter assembly 90 degrees counterclockwise and reinstall into the rubber hose. 9.
Page 331 Maintenance High fluid level If the fluid level is above the MAX range of the dipstick, remove fluid to reach the hashmark level. Note: Fluid level above the MAX level may cause shift and/or engagement concerns and/or possible damage. High fluid levels can be caused by an overheating condition. If your vehicle has been operated for an extended period at high speeds, in city traffic during hot weather or pulling a trailer, the vehicle should be turned off until normal operating temperatures are reached.
Page 332: Brake Fluid Check
Add fluid to fill the reservoir if the level is low. Only use a washer fluid that meets Ford specifications. See the technical specifications chart in the Capacities and Specifications chapter. Note: The front and rear washer systems are supplied from the same reservoir.
Page 333: Battery
Maintenance Washer fluids containing non-methanol antifreeze agents should be used only if they provide cold weather protection without damaging the vehicle’s paint finish, wiper blades or washer system. CHANGING THE VEHICLE BATTERY WARNING: Batteries normally produce explosive gases which can cause personal injury. Therefore, do not allow flames, sparks or lighted substances to come near the battery.
Page 334 Maintenance If you see any corrosion on the battery or terminals, remove the cables from the terminals and clean with a wire brush. You can neutralize the acid with a solution of baking soda and water. It is recommended that the negative battery cable terminal be disconnected from the battery if you plan to store your vehicle for an extended period of time.
Page 335 When a battery replacement is required, the battery should be replaced with a Ford recommended replacement battery that matches the electrical requirements of the vehicle. After battery replacement, or in some cases after charging the battery with an external charger, the BMS requires eight hours of vehicle sleep time (key off with doors closed) to relearn the new battery state of charge.
Page 336: Checking The Wiper Blades
Maintenance CHECKING THE WIPER BLADES Run the tip of your fingers over the edge of the blade to check for roughness. Clean the wiper blades with washer fluid or water applied with a soft sponge or cloth. CHANGING THE WIPER BLADES 1.
Page 337: Air Filter(S)
Maintenance 3. To attach the new wiper to the wiper arm, align the slot (1) and cross pin (2) and firmly press the wiper arm into the wiper blade until a click is heard. If you find this procedure too difficult, please see your dealer. AIR FILTER CHECK WARNING: To reduce the risk of vehicle damage and/or personal burn injuries, do not start your engine with the air cleaner...
Page 338 Maintenance Changing the Air Filter Element 3.5L V6 engine 2.0L EcoBoost® engine 3.5L V6 EcoBoost® engine 1. On the passenger’s side of the air filter housing, release the two clamps from the air filter housing cover. 2. Lift the passenger’s side of the cover and push the cover toward the passenger’s side.
Page 339: Adjusting The Headlamps
Maintenance 3. Carefully separate the cover from the housing. 4. Remove the air filter element from the housing. 5. Wipe the cover and the housing clean to remove any dirt or debris and to make sure the cover seals to the housing. 6.
Page 340 Maintenance • (1) 8 feet (2.4 meters) • (2) Center height of lamp to ground • (3) 25 feet (7.6 meters) • (4) Horizontal reference line 2. The center of the headlamp has a 3.0 millimeter circle on the lens. Measure the height from the center of your headlamp to the ground (2) and mark an 8 foot (2.4 meter) long horizontal line on the plain surface (1) at this height (masking tape works well).
Page 341: Changing A Bulb
Maintenance 5. Locate the vertical adjuster for each headlamp. Using a Phillips #2 screwdriver, turn the adjuster control either clockwise or counterclockwise in order to adjust the vertical aim of the headlamp. Note: HORIZONTAL AIMING IS NOT REQUIRED FOR THIS VEHICLE AND IS NON-ADJUSTABLE.
Page 342 Maintenance Replacing headlamp bulbs WARNING: Handle a halogen headlamp bulb carefully and keep out of children’s reach. Grasp the bulb only by its plastic base and do not touch the glass. The oil from your hand could cause the bulb to break the next time the headlamps are operated. Note: If the bulb is accidentally touched, it should be cleaned with rubbing alcohol before being used.
Page 343 Maintenance Front parking lamp/turn signal and sidemarker bulbs 1. Make sure that the headlamp control is in the off position. 2. Open the hood. 3. Remove the hood overslam bumper tower to service park/turn or sidemarker bulbs (if needed). Replacing front parking lamp/turn signal bulbs 1.
Page 344 Maintenance Replacing front fog lamp bulbs 1. Make sure the headlamp switch is off. 1. Make sure that the fog lamp switch is in the off position. 2. Remove the bulb socket from the fog lamp by turning it counterclockwise. 3.
Page 345: Bulb Specification Chart
Maintenance Carefully install the tail lamp assembly on the vehicle by securing the lamp assembly with two bolts. Reinstall bolt covers. Replacing tail/brake lamp bulbs For bulb replacement, see your authorized dealer. Replacing the License Plate Lamp Bulb 1. Carefully release the spring clip. 2.
Page 346 Maintenance Function Number of bulbs Trade number * Stop lamp * High-mount stop lamps Rear license plate lamp Front fog lamp Interior front map 168 (T10) lamps Second row 168 (T10) dome/courtesy lamp * Second row dome/map lamp * Third row cargo lamp Visor vanity lamp - Slideon rail system...
Page 347: Vehicle Care
Vehicle Care GENERAL INFORMATION Your Ford or Lincoln authorized dealer has many quality products available to clean your vehicle and protect its finishes. CLEANING PRODUCTS For best results, use the following products or products of equivalent quality: Motorcraft Bug and Tar Remover (ZC-42)
Page 348 Vehicle Care • Note: Suntan lotions and insect repellents can damage any painted surface; if these substances come in contact with your vehicle, wash it off as soon as possible. • Remove any exterior accessories before entering a car wash. Stripes or Graphics (if equipped) Do not use a commercial or high-pressure wand on the surface or edge of stripes and graphics.
Page 349: Waxing
Vehicle Care WAXING Regular waxing is necessary to protect the paint on your car from the elements. We recommend that you wash and wax the painted surface once or twice a year. When washing and waxing, park your vehicle in a shaded area out of direct sunlight.
Page 350: Cleaning The Windows And Wiper Blades
Vehicle Care • Spray Motorcraft Engine Shampoo and Degreaser on all parts that require cleaning and pressure rinse clean. In Canada, use Motorcraft Engine Shampoo. • Never wash or rinse the engine while it is hot or running; water in the running engine may cause internal damage.
Page 351: Cleaning The Interior
Vehicle Care CLEANING THE INTERIOR WARNING: Do not use cleaning solvents, bleach or dye on the vehicle’s safety belts, as these actions may weaken the belt webbing. WARNING: On vehicles equipped with seat-mounted airbags, do not use chemical solvents or strong detergents. Such products could contaminate the side airbag system and affect performance of the side airbag in a collision.
Page 352: Cleaning Leather Seats
Vehicle Care • Be certain to wash or wipe your hands clean if you have been in contact with certain products, such as insect repellent and suntan lotion, in order to avoid possible damage to the interior painted surfaces. • Do not use household or glass cleaners as these may damage the finish of the instrument panel, interior trim and cluster lens.
Page 353: Cleaning The Alloy Wheels
Vehicle Care • To check for compatibility, first test any cleaner or stain remover on an inconspicuous part of the leather. • Do not use household cleaning products, alcohol solutions, oil/petroleum-based leather conditioners, or solvents or cleaners intended specifically for rubber, vinyl and plastics. These products may cause premature wearing or damage to the leather.
Page 354 Vehicle Care General • Store all vehicles in a dry, ventilated place. • Protect from sunlight, if possible. • If vehicles are stored outside, they require regular maintenance to protect against rust and damage. Body • Wash vehicle thoroughly to remove dirt, grease, oil, tar or mud from exterior surfaces, rear-wheel housing and underside of front fenders.
Page 355 Vehicle Care Battery • Check and recharge as necessary. Keep connections clean. • If storing your vehicle for more than 30 days without recharging the battery, it may be advisable to disconnect the battery cables to ensure battery charge is maintained for quick starting. Note: If battery cables are disconnected, it will be necessary to reset memory features.
Page 356: Wheels And Tires
Wheels and Tires GENERAL INFORMATION Notice to Utility Vehicle, Van and Truck Owners WARNING: Utility vehicles have a significantly higher rollover rate than other types of vehicles. To reduce the risk of serious injury or death from a rollover or other crash you must: •...
Page 357 Wheels and Tires Power is supplied to all four wheels through a transfer case or power transfer unit. Four-wheel drive vehicles allow you to select different drive modes as necessary. You can find information on transfer case operation and shifting procedures in the Transmission chapter. You can find information on transfer case maintenance in the Maintenance chapter.
Page 358: Tire Care
• The Sport, optional 265/45ZR20 tires are optimized for performance in both wet and dry conditions. Ford does not recommend using the original equipment tires when temperatures drop to about 40°F (5°C) or below (depending on tire wear and environmental conditions) or in snow/ice conditions.
Page 359 Wheels and Tires • The Sport, optional 265/45ZR20 tires were designed for track use and may exhibit significantly reduced tread life and increased tire noise compared to the standard equipment tires under normal driving conditions. Increasing the front camber settings beyond the factory settings may further accelerate tread wear and induce tire noise.
Page 360 Wheels and Tires U.S. Department of Transportation-Tire quality grades: The U.S. Department of Transportation requires Ford Motor Company to give you the following information about tire grades exactly as the government has written it. Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course.
Page 361 Wheels and Tires Glossary of Tire Terminology • Tire label: A label showing the OE (Original Equipment) tire sizes, recommended inflation pressure and the maximum weight the vehicle can carry. • Tire Identification Number (TIN): A number on the sidewall of each tire providing information about the tire brand and manufacturing plant, tire size and date of manufacture.
Page 362 Wheels and Tires INFORMATION CONTAINED ON THE TIRE SIDEWALL Both U.S. and Canada Federal regulations require tire manufacturers to place standardized information on the sidewall of all tires. This information identifies and describes the fundamental characteristics of the tire and also provides a U.S.
Page 363 Wheels and Tires F. 95: Indicates the tire’s load index. It is an index that relates to how much weight a tire can carry. You may find this information in your owner’s manual. If not, contact a local tire dealer. Note: You may not find this information on all tires because it is not required by federal law.
Page 364 Wheels and Tires The numbers in between are identification codes used for traceability. This information is used to contact customers if a tire defect requires a recall. I. M+S or M/S: Mud and Snow, or AT: All Terrain, or AS: All Season. J.
Page 365 Wheels and Tires Additional Information Contained on the Tire Sidewall for LT Type Tires LT type tires have some additional information beyond those of P type tires. These differences are described below. Note: Tire Quality Grades do not apply to this type of tire. A.
Page 366 Wheels and Tires Information on T Type Tires T type tires have some additional information beyond those of P type tires. These differences are described below. T145/80D16 is an example of a tire size. Note: The temporary tire size for your vehicle may be different from this example.
Page 367 Always inflate your tires to the Ford recommended inflation pressure even if it is less than the maximum inflation pressure information found on the tire. The Ford recommended tire inflation pressure is found on the Safety Compliance Certification Label (affixed to either the door hinge pillar, door-latch post, or the door edge that meets the door-latch post, next to the driver’s seating position), or Tire Label which is located...
Page 368 Wheels and Tires Maximum Inflation Pressure is the tire manufacturer’s maximum permissible pressure or the pressure at which the maximum load can be carried by the tire. This pressure is normally higher than the manufacturer’s recommended cold inflation pressure, which can be found on the Safety Compliance Certification Label (affixed to either the door hinge pillar, door-latch post, or the door edge that meets the door-latch post, next to the driver’s seating position), or Tire Label which is located...
Page 369 Wheels and Tires Note: Some spare tires operate at a higher inflation pressure than the other tires. For T-type mini-spare tires, see the Dissimilar Spare Tire and Wheel Assembly Information section. Store and maintain at 60 psi (4.15 bar). For full-size and dissimilar spare tires, see Dissimilar Spare Tire and Wheel Assembly Information under Changing a Road Wheel in this chapter.
Page 370 Wheels and Tires Damage Periodically inspect the tire treads and sidewalls for damage (such as bulges in the tread or sidewalls, cracks in the tread groove and separation in the tread or sidewall). If damage is observed or suspected, have the tire inspected by a tire professional. Tires can be damaged during off-road use, so inspection after off-road use is also recommended.
Page 371 B-Pillar or edge of the driver’s door. If this information is not found on these labels, then you should contact your authorized dealer as soon as possible. Use of any tire or wheel not recommended by Ford can affect the safety and performance of your vehicle, which could result in an increased risk of loss of vehicle control, vehicle rollover, personal injury and death.
Page 372 The tire pressure sensors mounted in the wheels (originally installed on your vehicle) are not designed to be used in aftermarket wheels. The use of wheels or tires not recommended by Ford Motor Company may affect the operation of your tire pressure monitoring system.
Page 373 Wheels and Tires Safety Practices WARNING: If your vehicle is stuck in snow, mud, or sand, do not rapidly spin the tires. Spinning the tires can tear the tire and cause an explosion. A tire can explode in as little as three to five seconds. WARNING: Do not spin the wheels at over 35 mph (56 km/h).
Page 374 Mud and Snow (M+S or M/S) tire traction rating on the tire side wall. Since summer tires do not have the same traction performance as All-season or Snow tires, Ford does not recommend using summer tires when temperatures drop to approximately 40°F (5°C) or below (depending on tire wear and environmental conditions) or in snow and ice conditions.
Page 375: Using Snow Chains
WARNING: Snow tires must be the same size, load index and speed rating as those originally provided by Ford. Use of any tire or wheel not recommended by Ford can affect the safety and performance of your vehicle, which could result in an increased risk of loss of vehicle control, vehicle rollover, personal injury and death.
Page 376: Tire Pressure Monitoring System (Tpms)
Wheels and Tires TIRE PRESSURE MONITORING SYSTEM WARNING: The tire pressure monitoring system is NOT a substitute for manually checking tire pressure. The tire pressure should be checked periodically (at least monthly) using a tire gauge. See Inflating Your Tires in this chapter. Failure to properly maintain your tire pressure could increase the risk of tire failure, loss of control, vehicle rollover and personal injury.
Page 377 Wheels and Tires telltale after replacing one or more tires or wheels on your vehicle to ensure that the replacement or alternate tires and wheels allow the TPMS to continue to function properly. The tire pressure monitoring system complies with part 15 of the FCC rules and with RSS-210 of Industry Canada.
Page 378 Wheels and Tires When You Believe Your System Is Not Operating Properly The main function of the tire pressure monitoring system is to warn you when your tires need air. It can also warn you in the event the system is no longer capable of functioning as intended.
Page 379 Wheels and Tires Low tire Possible cause Customer action required pressure warning light Flashing Spare tire in use Repair the damaged road wheel warning light and tire assembly and reinstall it on the vehicle to restore system function. For a description on how the system functions, see When Your Temporary Spare Tire is Installed in this section.
Page 380: Changing A Road Wheel
Ford. If the dissimilar spare tire or wheel is damaged, it should be replaced rather than repaired.
Page 381 Wheels and Tires 2. Full-size dissimilar spare with label on wheel: This spare tire has a label on the wheel that states: THIS TIRE AND WHEEL FOR TEMPORARY USE ONLY When driving with one of the dissimilar spare tires listed above, do not: •...
Page 382 Wheels and Tires The usage of a full-size dissimilar spare tire and wheel assembly can lead to impairment of the following: • Handling, stability and braking performance • Comfort and noise • Ground clearance and parking at curbs • Winter weather driving capability •...
Page 383 Wheels and Tires WARNING: Do not attempt to change a tire on the side of the vehicle close to moving traffic. Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel.
Page 384 Wheels and Tires 4. Remove the wing nut securing the spare tire by turning it counterclockwise. 5. Lift and remove the spare tire from the spare tire well. 6. Remove the wing bolt that secures the jack kit by turning it counterclockwise. 7.
Page 385 Wheels and Tires Vehicle Jacking 1. Block the diagonally opposite wheel. 2. Loosen each wheel lug nut one-half turn counterclockwise but do not remove them until the wheel is raised off the ground. 3. The vehicle jacking points are shown here, and are depicted on the warning label on the jack.
Page 386 Wheels and Tires 8. Remove the jack and fully tighten the lug nuts in the order shown. See Wheel Lug Nut Torque Specifications later in this chapter for the proper lug nut torque specification. Stowing the mini-spare and jack 1. Adjust the jack to the proper height to install the wrench.
Page 387 Wheels and Tires Stowing the flat tire 1. Place the third-row seat in the raised position. 2. Secure the jack kit in the alternate position by inserting the L-shaped bolt through the hole in the side of the jack channel as shown. Note: The L-shaped bolt is located in the foam tray.
Page 388: Technical Specifications
N•m ⁄ x 20 * Torque specifications are for nut and bolt threads free of dirt and rust. Use only Ford recommended replacement fasteners. Note: Inspect the wheel pilot hole and mounting surface prior to installation. Remove any visible corrosion or loose particles.
Page 389: Capacities And Specifications
Capacities and Specifications ENGINE SPECIFICATIONS 3.5L V6 2.0L EcoBoost Engine 3.5L V6 engine EcoBoost engine engine Cubic inches Minimum Minimum Minimum Required fuel 87 octane 87 octane 87 octane Firing order 1–4–2–5–3–6 1–4–2–5–3–6 1-3-4-2 Ignition Coil on plug Coil on plug Coil on plug system Spark plug...
Page 390 Capacities and Specifications 2.0L EcoBoost engine A. Long drivebelt on the first pulley groove closer to the engine B. Short drivebelt on the second pulley groove farther from the engine 2014 Explorer (exp) Owners Guide gf, 3rd Printing, September 2013 USA (fus)
Page 391 Capacities and Specifications 2014 Explorer (exp) Owners Guide gf, 3rd Printing, September 2013 USA (fus)
Page 392 Capacities and Specifications 2014 Explorer (exp) Owners Guide gf, 3rd Printing, September 2013 USA (fus)
Page 393 Capacities and Specifications 2014 Explorer (exp) Owners Guide gf, 3rd Printing, September 2013 USA (fus)
Page 394 Capacities and Specifications 2014 Explorer (exp) Owners Guide gf, 3rd Printing, September 2013 USA (fus)
Page 395: Part Numbers
Note: Replace the spark plugs with ones that meet Ford material and design specifications for your vehicle, such as Motorcraft® or equivalent replacement parts. The customer warranty may be void for any damage to the engine if such spark plugs are not used.
Page 396: Vehicle Identification Number
Capacities and Specifications VEHICLE IDENTIFICATION NUMBER The vehicle identification number is located on the driver’s side instrument panel. XXXXXXXXXXXXXXXXX Please note that in the graphic, XXXX is representative of your vehicle identification number. The Vehicle Identification Number (VIN) contains the following information: A.
Page 397: Vehicle Certification Label
Capacities and Specifications VEHICLE CERTIFICATION LABEL The National Highway Traffic Safety Administration Regulations require that a Safety Compliance Certification Label be affixed to a vehicle and prescribe where the Safety Compliance Certification Label may be located. The Safety Compliance Certification Label shall be affixed to either the door hinge pillar, the door latch post, or the edge of the door near the door latch, next to the...
Page 398: Accessories
Ford Genuine Accessories found to be defective in factory-supplied materials or workmanship during the warranty period, as well as any component damaged by the defective accessories. Ford Motor Company will warrant your vehicle through the warranty that provides the greatest benefit: • 24 months, unlimited mileage.
Page 399 • If you or an authorized Ford dealer add any non-Ford electrical or electronic accessories or components to your vehicle, you may adversely affect battery performance and durability. In addition, you may also adversely affect the performance of other electrical systems in the vehicle.
Page 400: Extended Service Plan
SERVICE PLANS (U.S. Only) More than 32 million Ford owners have discovered the powerful protection of Ford Extended Service Plan. It is the only extended service plan backed by Ford Motor Company, and provides peace of mind protection beyond the New Vehicle Limited Warranty coverage.
Page 401 • Destination assistance for taxi, shuttle, rental car coverage and emergency transportation Transferable Coverage If you sell your vehicle before your Ford Extended Service Plan coverage expires, you can transfer any remaining coverage to the new owner. Whenever you sell your vehicle, prospective buyers may have a higher degree of confidence that vehicle was properly maintained with Ford ESP, thereby improving resale value.
Page 402 Ford ESP has to offer while paying over time. You are pre-approved with no credit checks, no hassles! To learn more, call our Ford ESP specialists at 800-367-3377. Ford ESP P.O.
Page 403: Audio System
Due to technical incompatibility, certain recordable and re-recordable compact discs may not function correctly when used in Ford CD players. Note: Do not insert CDs with homemade paper (adhesive) labels into the CD player as the label may peel and cause the CD to become jammed.
Page 404 Audio System MP3 Track and Folder Structure Audio systems capable of recognizing and playing MP3 individual tracks and folder structures work as follows: • There are two different modes for MP3 disc playback: MP3 track mode (system default) and MP3 folder mode. •...
Page 405: Myford™ System
Audio System MyFord® SYSTEM WARNING: Driving while distracted can result in loss of vehicle control, crash and injury. We strongly recommend that you use extreme caution when using any device that may take your focus off the road. Your primary responsibility is the safe operation of your vehicle.
Page 406 Audio System C. Memory presets: • In radio mode, store your favorite radio stations. To store a radio station, tune to the station, then press and hold a preset button until sound returns. • In CD mode, press one of these buttons to select a track. D.
Page 407 Audio System M. PHONE: Press this button to access the phone features of the SYNC system. See the SYNC chapter for more information. N. AUX: Press this button to access your auxiliary input jack or switch between devices you plug into the input jack or USB port. See Auxiliary input jack later in this chapter.
Page 408 Audio System SIRIUS Channel Guide Select to view available satellite radio channels. Press OK to open a list of the following options for this channel: Tune Channel, Skip Channel or Lock Channel. Once you skip or lock a channel, you can only access it by pressing Direct and entering the channel number.
Page 409 Audio System CD Settings Scan All Select to scan all disc selections. Scan Folder Select to scan all music in the current MP3 folder. CD Compression Select to bring soft and loud passages together for a more consistent listening level. Clock Settings Set Time Select to set the time.
Page 410 Audio System AM/FM/CD PREMIUM AUDIO SYSTEM WARNING: Driving while distracted can result in loss of vehicle control, crash and injury. We strongly recommend that you use extreme caution when using any device that may take your focus off the road. Your primary responsibility is the safe operation of your vehicle.
Page 411 Audio System E. SEEK, Reverse and Fast Forward: • In radio mode, select a frequency band and press one of these buttons. The system stops at the first station it finds in that direction. • In Sirius mode, press these buttons to select the previous or next channel.
Page 412 Audio System B. Seek, Reverse and Fast Forward: • In radio mode, select a frequency band and press one of these buttons. The system stops at the first station it finds in that direction. • In Sirius mode, press these buttons to select the previous or next channel.
Page 413 Audio System When HD Radio broadcasts are active, you can access the following functions: When you select: You can: Scan Hear a brief sampling of all available stations. This feature still works when HD Radio reception is on, although it does not scan for HD2-HD7 channels.
Page 414 Audio System HD Radio Reception and Station Troubleshooting Potential reception issues Reception area If you are listening to a multicast station and you are on the fringe of the reception area, the station may mute due to weak signal strength. If you are listening to HD1, the system switches back to the analog broadcast until the digital broadcast is available again.
Page 415 HD Radio™ Technology manufactured under license from iBiquity Digital Corp. U.S. and foreign patents. HD Radio™ and the HD and HD Radio logos are proprietary trademarks of iBiquity Digital Corp. Ford Motor Company and iBiquity Digital Corp. are not responsible for the content sent using HD Radio technology.
Page 416: Satellite Radio Information
Audio System SATELLITE RADIO INFORMATION (IF EQUIPPED) Satellite Radio Channels Sirius broadcasts a variety of music, news, sports, weather, traffic and entertainment satellite radio channels. For more information and a complete list of Sirius satellite radio channels, visit www.siriusxm.com in the United States, www.sirius.ca in Canada, or call Sirius at 1–888–539–7474.
Page 417 Note: Sirius reserves the unrestricted right to change, rearrange, add or delete programming including canceling, moving or adding particular channels, and its prices, at any time, with or without notice to you. Ford Motor Company shall not be responsible for any such programming changes. Sirius satellite radio is a...
Page 418 Audio System Radio display Condition Possible action Invalid Channel The channel is no Tune to another longer available. channel or choose another preset. Unsubscribed Channel Your subscription does Contact Sirius at not include this 1–888–539–7474 to channel. subscribe to the channel, or tune to another channel.
Page 419: Auxiliary Input Jack
Audio System AUXILIARY INPUT JACK WARNING: Driving while distracted can result in loss of vehicle control, crash and injury. We strongly recommend that you use extreme caution when using any device that may take your focus off the road. Your primary responsibility is the safe operation of your vehicle.
Page 420: Usb Port
Audio System 5. Switch your portable music player on and adjust its volume to half its maximum level. 6. Press AUX until LINE or LINE IN appears in the display. You should hear music from your device even if it is low. 7.
Page 421: Sync
SYNC® SYNC is an in-vehicle communications system that works with your Bluetooth-enabled cellular phone and portable media player. This allows you to: • Make and receive calls. • Access and play music from your portable music player. • Use 911 Assist, Vehicle Health Report and SYNC Services (Traffic, Directions &...
Page 422 SYNC® GENERAL INFORMATION Make sure you review your device’s manual before using it with SYNC. Support The SYNC support team is available to help you with any questions you cannot answer on your own. Monday-Saturday, 8:30am-9:00pm EST. Sunday, 10:30am-7:30pm EST. In the United States, call: 1–800–392–3673.
Page 423 Master Reset to erase all stored information. System data cannot be accessed without special equipment and access to the vehicle’s SYNC module. Ford Motor Company and Ford of Canada do not access the system data for any purpose other than as described...
Page 424 SYNC® USING VOICE RECOGNITION This system helps you control many features using voice commands. This allows you to keep your hands on the wheel and focus on what is in front of you. Initiating a Voice Session Push the voice icon; a tone sounds and Listening appears in the display.
Page 425 SYNC® Adjusting the Interaction Level Push the voice icon; when prompted, say “Voice settings”, then any of the following: When you say: The system: “Interaction mode standard” Provides more detailed interaction and guidance. “Interaction mode advanced” Provides less audible interaction and more tone prompts.
Page 426 SYNC® • Speak naturally, without long pauses between words. • At any time you can interrupt the system while it is speaking by pressing the voice icon. USING SYNC WITH YOUR PHONE Hands-free calling is one of the main features of SYNC. While the system supports a variety of features, many are dependent on your cellular phone’s functionality.
Page 427 SYNC® Depending on your phone’s capability and your market, the system may prompt you with questions such as setting the current phone as the primary phone (the phone SYNC automatically tries to connect with first upon vehicle start-up), downloading your phone book, etc. Pairing Subsequent Phones Note: To scroll through the menus, press the up and down arrows on your audio system.
Page 428 SYNC® “PHONE” “Call <name> at home” “Call <name> at work” OR “Call <name> in office” “Dial” “Phone book <name>” “Phone book <name> at work” OR “Phone book <name> at office” “Call history incoming” “Connections” “Go to privacy” “Hold” These commands do not require you to say “Phone” first. These commands are not available until phone information is completely downloaded using Bluetooth.
Page 429 SYNC® Phone book commands: When you ask SYNC® to access a phone book name, number, etc., the requested information appears in the display to view. Press the phone button and say “Call” to call the contact. “DIAL” “411” (four-one-one), “911” (nine-one-one) “700 (seven hundred)”...
Page 430 SYNC® Phone Options during an Active Call During an active call, you have additional menu features which become available such as putting a call on hold, joining calls, etc. Use the arrow buttons to scroll through the menu options. To access: 1.
Page 431 SYNC® When you select: You can: Access your phonebook contacts. Phonebook 1. Press OK to select, then scroll through your phonebook contacts. 2. Press OK again when the desired selection appears in the display. 3. Press the phone button. Access your call history log. Call History 1.
Page 432 SYNC® Accessing Features through the Phone Menu SYNC’s phone menu allows you to redial a number, access your call history and phone book and send text messages as well as access phone and system settings. You can also access advanced features, such as 911 Assist, Vehicle Health Report and SYNC Services.
Page 433 SYNC® When you select: You can: Enables you to send, download and delete Text Message text messages. Allows you to view your phone’s status, set Phone Settings ring tones, select your message notification, change phone book entries and automatically download your cellular phone among other features.
Page 434 SYNC® Receiving a Text Message Note: This is a phone-dependent feature. Your phone must support downloading text messages using Bluetooth to receive incoming text messages. Note: Forwarding a text message is a speed-dependent feature and can only be done when the vehicle is traveling at 3 mph (5 km/h) or less. Note: Only one recipient is allowed per text message.
Page 435 6. Press OK when the contact appears and press OK again to confirm when the system asks if you would like to send the message. Each text message is sent with the following signature: “This message was sent from my <Ford or Lincoln>”. Pre-defined text message options Can’t talk right now...
Page 436 SYNC® Accessing Your Phone Settings These are phone-dependent features. Your phone settings allow you to access and adjust features such as your ring tone, text message notification, modify your phone book and also set up automatic download. 1. Press the phone button. 2.
Page 437 SYNC® When you select: You can: Modify the contents of your phone book Modify Phonebook (such as add, delete, download). Press OK to select and scroll between: Add Contacts: Press OK to add more contacts from your phone book. Push the desired contact(s) on your phone.
Page 438 SYNC® System Settings System Settings provide access to your Bluetooth Devices and Advanced menu features. Use the arrow buttons to scroll through the menu options. The Bluetooth Devices menu allows you to add, connect, delete and set a phone as primary as well as turn your Bluetooth feature on and off. The Advanced menu allows you to access and set prompts, languages, defaults, perform a master reset, install an application and view system information.
Page 439 SYNC® If you select: You can: Set Bluetooth On/Off Turn the Bluetooth feature on and off. Press OK and scroll to toggle between On and Off. When the desired selection is chosen, press OK. Note: Turning Bluetooth off disconnects all Bluetooth devices and deactivates all Bluetooth features.
Page 440 SYNC® Advanced Menu Options This menu allows you to access settings such as prompts, languages, defaults, perform a master reset, install an application and view system information. 1. Press the phone button to enter the Phone Menu. 2. Scroll until System Settings appears and press OK. 3.
Page 441 SYNC® If you select: You can: Completely erase all information stored on Master Reset SYNC (phonebook, call history, text messages and paired devices) and return to the factory default settings. Press OK to select. The display indicates when complete and SYNC takes you back to the Advanced menu.
Page 442: Assist
SYNC® 911 Assist® WARNING: Unless the 911 Assist setting is set on prior to a crash, the system will not dial for help which could delay response time, potentially increasing the risk of serious injury or death after a crash. WARNING: Do not wait for 911 Assist to make an emergency call if you can do it yourself.
Page 443 SYNC® Setting 911 Assist On Perform the following: 1. Press the phone button to enter the Phone Menu. 2. Scroll until 911 Assist is selected. 3. Press OK to confirm and enter the 911 Assist menu. 4. Scroll to select between On and Off selections. 5.
Page 444: Vehicle Health Report
SYNC® If the call is not cancelled and a successful call is made, a pre-recorded message is played for the 911 operator, then the occupant(s) in the vehicle is able to talk with the operator. Be prepared to provide your name, phone number and location immediately, because not all 911 systems are capable of receiving this information electronically.
Page 445 SYNC® Note: In order to allow a break-in period for your vehicle, you may not be able to create a Vehicle Health Report until your vehicle odometer has reached 200 miles. Register for Vehicle Health Report and set your report preferences at www.SYNCMyRide.com.
Page 446 Certain versions or updates to Vehicle Health Report may also collect additional vehicle information. Ford may use the vehicle information it collects for any purpose. If you do not want to disclose your cellular phone number or vehicle information, do not run the feature or set up your Vehicle Health Report profile at www.SYNCMyRide.com.
Page 447 For more information, see SYNC Services Terms and Conditions at www.SYNCMyRide.com. If you do not want Ford or its service providers to collect the vehicle travel information or other information identified in the Terms and Conditions, do not activate or use the service.
Page 448 SYNC® Connecting to SYNC Services Using the Phone Menu 1. Press the phone button to enter the Phone Menu. 2. Scroll until Services appears in the display. 3. Press OK to confirm and enter the Services menu. The display indicates the system is connecting. 4.
Page 449 SYNC® Disconnecting from SYNC Services 1. Press and hold the phone button on the steering wheel. 2. Say “Good-bye” from the SYNC Services main menu. SYNC Services quick tips Personalizing You can personalize your Services feature to provide quicker access to your most used or favorite information.
Page 450 SYNC® SYNC is capable of hosting nearly any digital media player including: iPod, Zune™, Plays from device players, and most USB drives. SYNC also supports audio formats such as MP3, WMA, WAV and ACC. Connecting Your Digital Media Player via the USB Port Note: If your digital media player has a power switch, ensure that the device is turned on.
Page 451 SYNC® Media Voice Commands Press the voice icon and, when prompted, say “USB” then any of the following: “USB” “Autoplay off” “Autoplay on” “(Phone) (Media) (Bluetooth) Connections” “Pause” “Play” “Play album <name>” “Play all” “Play artist <name>” “Play genre <name>” “Play next folder”...
Page 452 SYNC® “USB” “Similar music” “What’s playing?” “<name>” is a dynamic listing, meaning that it could be the name of any desired group, artist, etc. Voice commands which are only available in folder mode. Voice commands which are not available until indexing is complete. Voice command guide “Autoplay”...
Page 453 SYNC® Voice command guide “Search/Play The system searches for a specific Artist/Track/Album” artist/track/album from the music indexed through the USB port. “Refine” This allows you to make your previous command more specific. For example, if you asked to search and play all music by a certain artist, you could then say “refine album”...
Page 454 SYNC® Media Menu Features The media menu allows you to select your media source, how to play your music (by artist, genre, shuffle, repeat, etc.), and also to add, connect or delete devices. 1. Press AUX and then MENU to enter the Media Menu. 2.
Page 455 SYNC® When you select: You can: Choose to shuffle or repeat your music and select Media Settings your Autoplay settings. Once these selections are turned on, they remain on until turned off. Press SEEK to play the previous or next track. Note: Some digital media players require both USB and line in ports to stream data and music separately.
Page 456 SYNC® If there are no media files to access, the display indicates there is no media. If there are media files, you have the following options to scroll through and select from: When you select: You can: Play All Play all indexed media (tracks) from your playing device in flat file mode, one at a time in numerical order.
Page 457 SYNC® When you select: You can: Sort indexed music by genre (category) type. Genres SYNC lists the genres alphabetically in flat file mode. If there are more than 255, SYNC automatically organizes them into alphabetical categories. Press OK to select and then scroll to select the desired genre and press OK.
Page 458 SYNC® When you select: You can: Similar Music Play music similar to what is currently playing from the USB port. The system uses the metadata information of each song to compile a playlist for you. Press OK to select. The system creates a new list of similar songs and begins playing.
Page 459 SYNC® Bluetooth Devices Menu Options This menu allows you to add, connect and delete devices as well as turn Bluetooth on and off. 1. Press AUX and then MENU to enter the Media Menu. 2. Scroll until System Settings appears and select OK. 3.
Page 460 SYNC® Advanced Menu Options This menu allows you to access settings such as prompts, language, performing a master reset as well as returning to factory defaults. 1. Press AUX and then MENU to access the Media Menu. 2. Scroll until System Settings appears and select OK. 3.
Page 461 SYNC® When you select: You can: Completely erase all information stored on Master Reset SYNC (all phonebook, call history, text messages and all paired devices) and return to the factory default settings. Download new software applications Application (if available) and then load the desired applications through your USB port.
Page 462 SYNC® Phone issues Issue Possible Possible solution(s) cause(s) • This is a • Go to the website to review SYNC is not able to download my phone-dependent your phone’s compatibility. • Try turning off the device, phonebook. feature, OR • Possible phone resetting the device or removing malfunction.
Page 463 SYNC® Phone issues Issue Possible Possible solution(s) cause(s) • This is a • Go to the website to review I am having trouble phone-dependent your phone’s compatibility. • Try turning off the device, connecting my feature, OR • Possible phone phone to SYNC.
Page 464 SYNC® USB and media issues Issue Possible Possible solution(s) cause(s) • Try turning off the device, I am having Possible device trouble malfunction. resetting the device or removing connecting my the device’s battery, then trying device. again. • Make sure you are using the manufacturer’s cable.
Page 465 SYNC® USB and media issues Issue Possible Possible solution(s) cause(s) • Your music files • Make sure that all song details SYNC does not recognize music may not contain are populated. • Some devices require you to that is on my the proper artist, device.
Page 466 SYNC® Vehicle Health Report and SYNC Services (Traffic, Directions and Information) issues Issue Possible Possible solution(s) cause(s) I am unable to The preferred When you register your account, retrieve the dealer you must list a preferred dealer. report on the information did If one is already listed, try website, or I...
Page 467 SYNC® Voice command issues Issue Possible Possible solution(s) cause(s) • You may be • Review the Phone voice SYNC does not understand what using the wrong commands and the Media voice I am saying. voice commands, commands at the beginning of their respective sections.
Page 468 SYNC® Voice command issues Issue Possible Possible solution(s) cause(s) • You may be • Review the phone voice SYNC does not understand or is using the wrong commands at the beginning of calling the wrong voice commands, the phone section. •...
Page 469 SYNC® AppLink issues Issue Possible Possible solution(s) cause(s) • Your device • Check the website for SYNC does not find any mobile may not support compatible devices and apps that are on the AppLink applications. • Make sure your device is my phone.
Page 470: Myford Touch® (If Equipped)
MyFord Touch® (If Equipped) INTRODUCTION WARNING: Driving while distracted can result in loss of vehicle control, crash and injury. We strongly recommend that you use extreme caution when using any device that may take your focus off the road. Your primary responsibility is the safe operation of your vehicle.
Page 471 MyFord Touch® (If Equipped) Note: Some features are not available while your vehicle is moving. Note: Your system is equipped with a feature that allows you to access and control audio features for 30 minutes after you switch the ignition off (and no doors open).
Page 472 MyFord Touch® (If Equipped) SETTINGS Press to select any of the following: • Clock • Display • Sound • Vehicle • Settings • Help HOME Press to access your home screen. Depending on your vehicle’s option package and software, your screens may vary in appearance from the descriptions in this section.
Page 473 MyFord Touch® (If Equipped) Using the Touch-sensitive Controls on Your System To turn a feature on and off, just touch the graphic with your finger. To get the best performance from the touch-sensitive controls: • Do not press hard on the controls. They are sensitive to light touch. •...
Page 474 MyFord Touch® (If Equipped) Support The SYNC support team is available to help you with any questions you cannot answer on your own. Monday-Saturday, 8:30am-9:00pm EST. Sunday, 10:30am-7:30pm EST. In the United States, call: 1–800–392–3673. In Canada, call: 1–800–565–3673. Times are subject to change due to holidays. Safety Information WARNING: Driving while distracted can result in loss of vehicle control, crash and injury.
Page 475 MyFord Touch® (If Equipped) Speed-restricted Features Some features of this system may be too difficult to use while your vehicle is moving so they are restricted from use unless your vehicle is stationary. • Screens that are too crowded with information, such as Point of Interest reviews and ratings, Sirius Travel Link sports scores, movie times and ski conditions.
Page 476 Master Reset to erase all stored information. System data cannot be accessed without special equipment and access to the vehicle’s SYNC module. Ford Motor Company and Ford of Canada do not access the system data for any purpose other than as described...
Page 477 MyFord Touch® (If Equipped) ACCESSING AND ADJUSTING MODES THROUGH YOUR RIGHT VEHICLE INFORMATION DISPLAY (IF EQUIPPED) The display is located on the right side of your instrument cluster. You can use your steering wheel controls to view and make minor adjustments to active modes without taking your hands off the wheel.
Page 478: Voice Recognition
MyFord Touch® (If Equipped) Audio Sources and Memory Presets Use the OK and arrow buttons on the right side of your steering wheel to scroll through the available modes. You can make selections from the menu by using the OK button. The selection menu expands and different options appear.
Page 479 MyFord Touch® (If Equipped) How to Use Voice Commands with Your System Press the voice icon. After the tone, speak your command clearly. These commands can be said at any time. “Cancel” “Exit” “Go back” “List of commands” “Main menu” “Next page”...
Page 480 MyFord Touch® (If Equipped) Accessing a List of Available Commands • If you use the touchscreen, press the Settings icon > Help > Voice Command List. • If you use the steering wheel control, press the voice icon. After the tone, speak your command clearly.
Page 481 MyFord Touch® (If Equipped) Confirmation Prompts: The system uses these short questions to confirm your voice request. If turned off, the system simply makes a best guess as to what you requested. The system may still occasionally ask you to confirm settings. Phone/Media Candidate Lists: Candidate lists are lists of possible results from your voice commands.
Page 482 MyFord Touch® (If Equipped) ENTERTAINMENT A. AM 1 and AM AST B. FM 1, FM 2 and FM AST C. SIRIUS D. CD E. USB F. Touch this button to scroll down for more options, such as: • SD Card •...
Page 483 MyFord Touch® (If Equipped) Browsing Device Content When listening to audio on a device, you can browse through other devices without having to change sources. For example, if you are currently listening to audio on an SD card, you can browse all the artists that are stored on your USB device.
Page 484: Listening To Music
MyFord Touch® (If Equipped) Your voice system allows you to change audio sources with a simple voice command. For example, if you are listening to music on a USB device, then want to switch to a satellite radio channel, simply press the voice button on the steering wheel controls and say the name of the Sirius station (such as, “the Highway”).
Page 485 MyFord Touch® (If Equipped) Scan Touch this button to go to the next strong AM or FM radio station. The light on the button illuminates when the feature is on. Options Sound Settings allows you to adjust settings for: • Bass •...
Page 486 MyFord Touch® (If Equipped) HD Radio™ Information (If Available) Note: HD Radio broadcasts are not available in all markets. HD Radio technology is the digital evolution of analog AM/FM radio. Your system has a special receiver that allows it to receive digital broadcasts (where available) in addition to the analog broadcasts, it already receives.
Page 487 MyFord Touch® (If Equipped) When HD Radio broadcasts are active, you can access the following functions: • Scan allows you to hear a brief sampling of all available stations. This feature still works when HD Radio reception is on, although it does not scan for HD2-HD7 channels.
Page 488 HD Radio Technology manufactured under license from iBiquity Digital Corp. U.S. and foreign patents. HD Radio and the HD and HD Radio logos are proprietary trademarks of iBiquity Digital Corp. Ford Motor Company and iBiquity Digital Corp. are not responsible for the content sent using HD Radio technology.
Page 489 MyFord Touch® (If Equipped) Radio Voice Commands If you are listening to the radio, press the voice button on the steering wheel control. When prompted, say any of the commands in the following chart. If you are not listening to the radio, press the voice button and, after the tone, say “Radio”, then any of the commands in the following chart.
Page 490 MyFord Touch® (If Equipped) Sirius Satellite Radio (If Activated) Press the lower left corner of the touchscreen, then select the SIRIUS tab. Presets Save a channel by pressing and holding one of the memory preset areas. There is a brief mute while the radio saves the channel. Sound returns when finished.
Page 491 Note: Sirius does not support the Alert feature on all channels. Ford Motor Company shall not be responsible for Alert feature variation. Electronic Serial Number (ESN) is required when you need to activate, modify or track your satellite radio account.
Page 492 MyFord Touch® (If Equipped) If you are not listening to Sirius satellite radio, press the voice button and, after the tone, say “Sirius”, then any of the commands in the following chart. “SIRIUS” “Sirius <0–223>” “SAT 3” “<Channel name>” “SAT 3 preset <#>” “Preset <#>”...
Page 493 Note: Sirius reserves the unrestricted right to change, rearrange, add or delete programming including canceling, moving or adding particular channels, and its prices, at any time, with or without notice to you. Ford Motor Company shall not be responsible for any such programming changes.
Page 494 MyFord Touch® (If Equipped) Sirius troubleshooting tips Radio display Condition Possible action Acquiring... Radio requires more No action required. than two seconds to This message should produce audio for the disappear shortly. selected channel. Sat Fault/SIRIUS There is an internal If this message does system failure.
Page 495 MyFord Touch® (If Equipped) Sirius troubleshooting tips Radio display Condition Possible action None Found. Check All the channels in the Use the channel guide Channel Guide. selected channels are to turn off the Lock either skipped or or Skip function on locked.
Page 496 MyFord Touch® (If Equipped) Compression allows you to turn the compression feature on and off. Browse Touch this button to look through all available CD tracks. CD Voice Commands If you are listening to a CD, press the voice button on the steering wheel control.
Page 497 MyFord Touch® (If Equipped) SD logo is a trademark of SD-3C, LLC. USB Port The ports are located either in the center console or behind a small access door in the instrument panel. To access and play music from your device, press the lower left corner of the touchscreen, and then select the USB tab.
Page 498 MyFord Touch® (If Equipped) Note: Your vehicle may not have all these sound settings. • Media Player Settings allows you to select more settings, which is under Media Player. See Settings. • Device Information displays software and firmware information about the currently connected media device. •...
Page 499 MyFord Touch® (If Equipped) “USB” or “SD CARD” “Play movie <name>” “Repeat one” “Play music video <name>” “Shuffle” “Play next song” “Shuffle off” “Play playlist <name>” “What’s this?” “Play podcast <name>” “Help” “Play podcast episode <name>” If you have said you would like to browse your USB or SD card, the system prompts you to specify what you would like to browse.
Page 500 MyFord Touch® (If Equipped) Supported Media Players, Formats and Metadata Information SYNC is capable of hosting nearly any digital media player, including iPod®, Zune™, plays from device players, and most USB drives. Supported audio formats include MP3, WMA, WAV and AAC. It is also able to organize your indexed media from your playing device by metadata tags.
Page 501 MyFord Touch® (If Equipped) Line In (Auxiliary Input Jack) WARNING: Driving while distracted can result in loss of vehicle control, crash and injury. We strongly recommend that you use extreme caution when using any device that may take your focus off the road.
Page 502 MyFord Touch® (If Equipped) 7. Adjust the volume on your portable music player until it reaches the volume level of the FM station or CD. Do this by switching back and forth between the AUX and FM or CD controls. Troubleshooting •...
Page 503: Pairing Your Phone For The First Time
MyFord Touch® (If Equipped) Hands-free calling is one of the main features of SYNC. Once you pair your phone, you can access many options using the touchscreen or voice commands. While the system supports a variety of features, many are dependent on your cellular phone’s functionality.
Page 504 MyFord Touch® (If Equipped) 3. If you are prompted to enter a PIN on your device, it does not support Secure Simple Pairing. To pair, enter the PIN displayed on the touchscreen. Skip the next step. 4. When prompted on your phone’s display, confirm that the PIN provided by SYNC matches the PIN displayed on your cellular phone.
Page 505 MyFord Touch® (If Equipped) Receiving Calls During an incoming call, an audible tone sounds. Call information appears in the display if it is available. Accept the call by pressing Accept on the touchscreen or by pressing this phone button on your steering wheel controls Reject the call by pressing Reject on the touchscreen or by pressing this phone button on your steering wheel controls.
Page 506 MyFord Touch® (If Equipped) Messaging Send text messages using your touchscreen. See Text messaging later in this section. Settings Touch this button to access various phone settings, such turning Bluetooth on and off, managing your phonebook and more. See Phone settings later in this section.
Page 507 MyFord Touch® (If Equipped) Pre-defined text message options I’ll call you back in a few minutes. I just left, I’ll be there soon. Can you give me a call? I’m on my way. I’m running a few minutes late. I’m ahead of schedule, so I’ll be there early. I’m outside.
Page 508 MyFord Touch® (If Equipped) Bluetooth Touch this tab to turn Bluetooth off or on. Do Not Disturb Touch this tab if you want all calls to go directly to your voice mail and not ring in the vehicle. When this feature is on, text message notifications do not ring inside the cabin either.
Page 509 MyFord Touch® (If Equipped) Phone Voice Commands Press the voice button on the steering wheel control. After the tone, say any of the following commands: “PHONE” “Call” “Join calls” “Call <name>” “Listen to text message <#>” “Call <name> at home” “Listen to text messages”...
Page 510: Information Menu
Note: SYNC Services varies by trim level and model year and may require a subscription. Traffic alerts and turn-by-turn directions available in select markets. Message and data rates may apply. Ford Motor Company reserves the right to change or discontinue this product service at any time without prior notification or incurring any future obligation.
Page 511 For more information, see SYNC Services Terms and Conditions at www.SYNCMyRide.com. If you do not want Ford or its service providers to collect your vehicle travel information or other information identified in the Terms and Conditions, do not subscribe or use the service.
Page 512 MyFord Touch® (If Equipped) Connecting to SYNC Services Using the Touchscreen If your vehicle is equipped with Navigation, touch the i (Information) button to access these features. If your vehicle is not equipped with Navigation, touch the corner of the touchscreen with the green tab.
Page 513 MyFord Touch® (If Equipped) If you miss a turn, SYNC automatically asks if you want the route updated. Just say, “Yes” when prompted and the system delivers a new route to your vehicle. If your vehicle is equipped with Navigation, SYNC Services downloads your requested destination to the navigation system.
Page 514 Sirius Travel Link. Note: Neither Sirius nor Ford is responsible for any errors or inaccuracies in the Sirius Travel Link services or its use in vehicles. 2014 Explorer (exp)
Page 515 MyFord Touch® (If Equipped) When you subscribe to Sirius Travel Link, it can help you locate the best gas prices, find movie listings, get current traffic alerts, view the current weather map, get accurate ski conditions and see scores to current sports games.
Page 516 MyFord Touch® (If Equipped) Sirius Travel Link Voice Commands Note: In order to use Sirius Travel Link, your vehicle must be equipped with navigation and your navigation SD card must be in the SD card slot. Press the voice button on the steering wheel controls and, when prompted, say any of the following: Travel Link voice commands “5–day weather forecast”...
Page 517 MyFord Touch® (If Equipped) “TRAVEL LINK” “College basketball “Motor sports order” “NHL schedule” schedule” “College basketball “Motor sports “NHL scores” scores” schedule” “College football “Movie listings” “Traffic” headlines” “College football “My team headlines” “Weather” schedule” “College football “My teams schedule” “Weather map”...
Page 518 MyFord Touch® (If Equipped) 911 Assist® (If Equipped) WARNING: Unless the 911 Assist setting is set on before a crash, the system will not dial for help, which could delay response time, potentially increasing the risk of serious injury or death after a crash.
Page 519 MyFord Touch® (If Equipped) Setting 911 Assist On If your vehicle is equipped with Navigation, touch the i (Information) button to access these features. If your vehicle is not equipped with Navigation, touch the corner of the touchscreen with the green tab. Press Apps >...
Page 520 MyFord Touch® (If Equipped) If you do not cancel the call, and SYNC makes a successful call, a pre-recorded message plays for the 911 operator, and then the occupant(s) in your vehicle is able to talk with the operator. Be prepared to provide your name, phone number and location immediately, because not all 911 systems are capable of receiving this information electronically.
Page 521 “Vehicle health report”. Vehicle Health Report Privacy Notice When you create a Vehicle Health Report, Ford Motor Company may collect your cellular phone number (to process your report request) and diagnostic information about your vehicle. Certain versions or updates to Vehicle Health Report may also collect more vehicle information.
Page 522: Settings
MyFord Touch® (If Equipped) SETTINGS A. Clock B. Display C. Sound D. Vehicle E. Settings F. Help Under this menu, you can set your clock, access and adjust the display, sound and vehicle settings as well as access settings for specific modes or the help feature.
Page 523 MyFord Touch® (If Equipped) You can also turn the outside air temperature display on and off. It appears at the top center of the touchscreen, next to the time and date. The system automatically saves any updates you make to the settings. Display You can adjust the touchscreen display through the touchscreen or by pressing the voice button on your steering wheel controls and when...
Page 524 MyFord Touch® (If Equipped) Only the photograph(s), which meets the following conditions, display: • Compatible file formats are as follows: .jpg, .gif, .png, .bmp. • Each file must be 1.5 MB or less. • Recommended dimensions: 800 x 384. Sound Press the Settings icon >...
Page 525 MyFord Touch® (If Equipped) Door Keypad Code To change the keypad code for your keyless entry keypad system: 1. Press the Settings icon > Vehicle > Door Keypad Code. 2. Enter your current factory code, then, when prompted, enter your new code.
Page 526 MyFord Touch® (If Equipped) System Touch Screen Button Select to have the system beep to confirm Beep choices made through the touchscreen. Touch Panel Button Select to have the system beep to confirm Beep button choices made through the climate or audio system.
Page 527 MyFord Touch® (If Equipped) Voice control Phone Candidate Candidate lists are possible results from your Lists voice commands. The system simply makes a best guess at your request with these turned off. Voice Control Volume This allows you to adjust the system’s voice volume level.
Page 528 MyFord Touch® (If Equipped) Navigation Press the Settings icon > Settings > Navigation, then select from the following: Navigation Map Preferences Turn breadcrumbs on and off. Have the system display your turn list top to bottom or bottom to top. Turn the Parking POI notification on and off.
Page 529 MyFord Touch® (If Equipped) Navigation Traffic Preferences Have the system display areas where roadwork occurs. Have the system display incident icons. Have the system display areas where difficult driving conditions may occur. Have the system display areas where snow and ice on the road may occur. Have the system display any smog alerts.
Page 530 MyFord Touch® (If Equipped) Phone Phone Ringer Select the type of notification for phone calls - ring tone, beep, text to speech, or have it be silent. Text Message Select the type of notification for text Notification messages - alert tone, beep, text to speech, or have it be silent.
Page 531 MyFord Touch® (If Equipped) Press the Settings icon > Settings > Wireless & Internet, then select from the following: Wireless & Internet Wi-Fi Settings Wi-Fi Network (Client) Mode turns the Wi-Fi feature on and off in your vehicle. Make sure you turn it on for connectivity purposes. Choose a Wireless Network allows you to use a previously stored wireless network.
Page 532 MyFord Touch® (If Equipped) Wireless & Internet USB Mobile Instead of using Wi-Fi, your system can also Broadband use a USB mobile broadband connection to access the internet. (You must turn on your mobile broadband device on your personal computer before connecting it to the system.) This screen allows you to set up what is your typical area for your USB mobile broadband connection.
Page 533 MyFord Touch® (If Equipped) Help Press the Settings icon > Help, then select from the following: Help Where Am I? View your vehicle’s current location, if your vehicle is equipped with navigation. If your vehicle is not equipped with navigation, nothing displays.
Page 534 MyFord Touch® (If Equipped) To access Help using the voice commands, press the voice button, then, after the tone, say “Help”. The system provides allowable voice commands for the current mode. CLIMATE Press the lower right corner on the touchscreen to access your climate control features.
Page 535 MyFord Touch® (If Equipped) • To adjust fan speed, touch + or – next to the fan icon. • Touch Rear again to close the rear controls. Closing the rear climate control functions does not affect their current settings. E. Recirculated air: Touch to turn the recirculated air on or off which: •...
Page 536 MyFord Touch® (If Equipped) • Panel and Floor: Distributes air through the instrument panel vents, demister vents, floor vents and rear seat floor vents. • Floor: Distributes air through the demister vents, floor vents and rear seat floor vents. L. Driver settings: Depending on your vehicle and option package, you may have the following features: •...
Page 537: Navigation System
MyFord Touch® (If Equipped) There are additional climate control commands but in order to access them, you have to say “Climate” first, then when the system is ready to listen, you may say any of the following commands: Additional climate control voice commands “Automatic”...
Page 538 MyFord Touch® (If Equipped) Your navigation system is comprised of two main features, destination mode and map mode. To set a destination, press the green corner of your touchscreen, then Dest when it appears. See Setting a destination later in this chapter. To view the navigation map and your vehicle’s current location, touch the green bar in the upper right hand corner of the touchscreen, or, press Dest >...
Page 539 MyFord Touch® (If Equipped) Note: If your vehicle is on a recognized road and you do not press the Start Route button, the system defaults to the Fastest Route option and begins guidance. During route guidance, you can press the talking bubble icon that appears in the upper right navigation corner (green bar) if you want the system to repeat route guidance information.
Page 540 MyFord Touch® (If Equipped) Pressing the Search Areas button allows you to search for points of interest nearby, near a city or state or near a destination, if a route is active. Pressing the Search By Name button allows you to directly enter the point of interest name into the system by using the keyboard.
Page 541 MyFord Touch® (If Equipped) Nightlife Attraction This icon appears when your selection exists in multiple categories within the system. When you are viewing more information for hotels, cityseekr also tells you if the hotel has certain services and facilities using icons. Hotel services and facilities Restaurant 24 Hr Room Service...
Page 542 MyFord Touch® (If Equipped) Map Preferences Breadcrumbs displays your vehicle’s previously traveled route with white dots. Turn this feature ON or OFF. Turn List Format allows you to choose to have the system display your turn list Top to Bottom or Bottom to Top. Parking POI Notification sets the automatic parking points of interest notification.
Page 543 MyFord Touch® (If Equipped) Traffic Preferences Avoid Traffic Problems allows you to choose how you want the system to handle traffic problems along your route. • Automatic: Have the system reroute you to avoid traffic incidents that develop and impact the current route. The system does not provide a traffic alert notification.
Page 544 MyFord Touch® (If Equipped) Change the appearance of the map display by repeatedly pressing the arrow button in the upper left corner of the screen. It toggles between three different map modes: Heading up, North up, and 3D. Heading up (2D map) always shows the direction of forward travel to be upward on the screen.
Page 545 MyFord Touch® (If Equipped) In 3D mode, rotate the map view by swiping your finger across the shaded bar with the arrows. Map Icons Vehicle mark shows the current location of your vehicle. It stays in the center of the map display, except when in scroll mode.
Page 546 MyFord Touch® (If Equipped) No GPS symbol indicates that insufficient GPS satellite signals are available for accurate map positioning. This icon may display under normal operation in an area with poor GPS access. Quick-touch Buttons When in map mode, touch anywhere on the map display to access more features.
Page 547 Annual navigation map updates are available for purchase through your dealership, by calling 1-800-NAVMAPS (in Mexico, call 01–800–557–5539) or going to www.navigation.com/ford. You need to specify the make and model of your vehicle to determine if there is an update available.
Page 548 MyFord Touch® (If Equipped) “DESTINATION” “<nametag>” “<POI category>” “Favorites” “Home” “Intersection” “Nearest <POI category>” “Nearest POI” “Play nametags” “POI category” “Previous destination” “Street address” “Help” “NAVIGATION” “Destination” “Zoom city” “Zoom country” “Zoom in minimum” “Zoom out maximum” “Zoom province” “Zoom state” “Zoom street”...
Page 549: Appendices
SYNC® End User License Agreement (EULA) • You have acquired a device (“DEVICE”) that includes software licensed by Ford Motor Company and its affiliates (“FORD MOTOR COMPANY”) from an affiliate of Microsoft Corporation (“MS”). Those installed software products of MS origin, as well as associated media, printed materials, and “online”...
Page 550 Neither FORD MOTOR COMPANY nor its suppliers shall be liable for any damages arising out of errors in the speech recognition process.
Page 551 • Consent to Use of Data: You agree that MS, Microsoft Corporation, FORD MOTOR COMPANY, third party software and systems suppliers, their affiliates and/or their designated agent may collect and use technical information gathered in any manner as part of product support services related to the SOFTWARE or related services.
Page 552 DEVICE. UPGRADES AND RECOVERY MEDIA: If the SOFTWARE is provided by FORD MOTOR COMPANY separate from the DEVICE on media such as a ROM chip, CD ROM disk(s) or via web download or other means, and is labeled “For Upgrade Purposes Only” or For Recovery Purposes...
Page 553 U.S. and other governments. For additional information, see http://www.microsoft.com/exporting/. TRADEMARKS: This EULA does not grant you any rights in connection with any trademarks or service marks of FORD MOTOR COMPANY, MS, Microsoft Corporation, third party software or service providers, their affiliates or suppliers.
Page 554 End user notice Microsoft® Windows® Mobile for Automotive Important Safety Information This system Ford SYNC™ contains software that is licensed to Manufacturer FORD MOTOR COMPANY by an affiliate of Microsoft Corporation pursuant to a license agreement. Any removal, reproduction, reverse engineering or other unauthorized use of the software from this system in violation of the license agreement is strictly prohibited and may subject you to legal action.
Page 555 Appendices Keep User’s Guide in Vehicle When kept in the vehicle, the User’s Guide will be a ready reference for you and other users unfamiliar with the Windows Automotive-based system. Please make certain that before using the system for the first time, all persons have access to the User’s Guide and read its instructions and safety information carefully.
Page 556 Appendices Navigation Features Any navigation features included in the system are intended to provide turn by turn instructions to get you to a desired destination. Please make certain all persons using this system carefully read and follow instructions and safety information fully. Distraction Hazard Any navigation features may require manual (non-verbal) setup.
Page 557 Appendices TeleNav Software End User License Agreement Please read these terms and conditions carefully before you use the Telenav Software. Your use of the Telenav Software indicates that you accept these terms and conditions. If you do not accept these terms and conditions, do not break the seal of the package, launch, or otherwise use the Telenav Software.
Page 558 Appendices 2. Account Information You agree: (a) when registering the Telenav Software, to provide Telenav with true, accurate, current, and complete information about yourself, and (b) to inform Telenav promptly of any changes to such information, and to keep it true, accurate, current and complete. 3.
Page 559 Appendices reflect reality due to, among other things, road closures, construction, weather, new roads and other changing conditions. You are responsible for the entire risk arising out of your use of the Telenav Software. For example but without limitation, you agree not to rely on the Telenav Software for critical navigation in areas where the well-being or survival of you or others is dependent on the accuracy of navigation, as the maps or functionality of the Telenav Software are not intended to support such...
Page 560 Appendices 6. Arbitration and Governing Law You agree that any dispute, claim or controversy arising out of or relating to this Agreement or the Telenav Software shall be settled by independent arbitration involving a neutral arbitrator and administered by the American Arbitration Association in the County of Santa Clara, California.
Page 561 Appendices 8. Miscellaneous 8.1 This Agreement constitutes the entire agreement between Telenav and you with respect to the subject matter hereof. 8.2 Except for the limited licenses expressly granted in this Agreement, Telenav retains all right, title and interest in and to the Telenav Software, including without limitation all related intellectual property rights.
Page 562 Appendices 9. Other Vendors Terms and Conditions The Telenav Software utilizes map and other data licensed to Telenav by third party vendors for the benefit of you and other end users. This Agreement includes end-user terms applicable to these companies (included at the end of this Agreement), and thus your use of the Telenav Software is also subject to such terms.
Page 563 Appendices License Limitations on Transfer: Your limited license does not allow transfer or resale of the Data, except on the condition that you may transfer the Data and all accompanying materials on a permanent basis if: (a) you retain no copies of the Data; (b) the recipient agrees to the terms of this End-User License Agreement;...
Page 564 Appendices Disclaimer of Liability: HERE AND ITS LICENSORS (INCLUDING THEIR LICENSORS AND SUPPLIERS) SHALL NOT BE LIABLE TO YOU IN RESPECT OF ANY CLAIM, DEMAND OR ACTION, IRRESPECTIVE OF THE NATURE OF THE CAUSE OF THE CLAIM, DEMAND OR ACTION ALLEGING ANY LOSS, INJURY OR DAMAGES, DIRECT OR INDIRECT, WHICH MAY RESULT FROM THE USE OR POSSESSION OF THIS DATA;...
Page 565 Appendices (“Claims”), you agree to submit to the personal jurisdiction of (a) the State of Illinois for Claims related to Data for the Americas and/or the Asia Pacific region provided to you hereunder, and (b) The Netherlands for Data for Europe, the Middle East and/or Africa provided to you hereunder.
Page 566 Appendices Gracenote and CDDB are registered trademarks of Gracenote. The Gracenote logo and logotype, and the Powered by Gracenote™ logo are trademarks of Gracenote. Gracenote® End User License Agreement (EULA) This device contains software from Gracenote, Inc. of 2000 Powell Street Emeryville, California 94608 (“Gracenote”).
Page 567 Appendices Gracenote uses a unique identifier to track queries for statistical purposes. The purpose of a randomly assigned numeric identifier is to allow Gracenote to count queries without knowing anything about who you are. For more information, see the web page at www.gracenote.com for the Gracenote Privacy Policy THE GRACENOTE SOFTWARE, EACH ITEM OF GRACENOTE DATA AND THE GRACENOTE CONTENT ARE LICENSED TO YOU “AS IS.”...
Page 568 Appendices This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Page 569: Scheduled Maintenance
Parts installed at your dealership carry a nationwide 24-month or unlimited miles (kilometers) parts and labor limited warranty. If you do not use Ford authorized parts they may not meet our specifications and depending on the part, it could affect emissions compliance.
Page 570 Ford Motor Company has recommended maintenance intervals for various parts and component systems based upon engineering testing. Ford Motor Company relies upon this testing to determine the most appropriate mileage for replacement of oils and fluids to protect your vehicle at the lowest overall cost to you and recommends against maintenance schedules that deviate from the scheduled maintenance information.
Page 571 Scheduled Maintenance Ford strongly recommends the use of only genuine Ford, Motorcraft or Ford-authorized remanufactured replacement parts because they are engineered for your vehicle. Additives and Chemicals Ford Motor Company recommended additives and chemicals are listed in the owner manual and in the Ford Workshop Manual. Additional chemicals or additives not approved by Ford Motor Company are not recommended as part of normal maintenance.
Page 572 In order to keep your vehicle running right, it is important to have the systems on your vehicle checked regularly. This can help identify potential issues and prevent major problems. Ford Motor Company recommends the following multi-point inspection be performed at every scheduled maintenance interval to help make sure your vehicle keeps running great.
Page 573 Scheduled Maintenance 2014 Explorer (exp) Owners Guide gf, 3rd Printing, September 2013 USA (fus)
Page 574: Normal Scheduled Maintenance And Log
Scheduled Maintenance NORMAL SCHEDULED MAINTENANCE AND LOG Intelligent Oil-Life Monitor® Your vehicle is equipped with an Intelligent Oil-Life Monitor that determines when the engine oil needs to be changed based on how your vehicle is used. By using several important factors in its calculations, the monitor helps reduce the cost of owning your vehicle and reduce environmental waste at the same time.
Page 575 Scheduled Maintenance Normal scheduled maintenance At every oil change Change engine oil and filter. interval as indicated by Rotate tires, inspect tire wear and measure the information display tread depth. Perform multi-point inspection (recommended). Inspect automatic transmission fluid level (if equipped with dipstick).
Page 576 Scheduled Maintenance Other maintenance items Every 20000 miles Replace cabin air filter (if equipped). (32000 km) Every 30000 miles Replace climate-controlled (heated and (48000 km) cooled) seat filter. Replace engine air filter. At 100000 miles Change engine coolant. (160000 km) Every 100000 miles Replace spark plugs.
Page 577 Scheduled Maintenance Maintenance Schedule Log EALER ALIDATION EALER ALIDATION P&A C P&A C RO#: RO#: OURS OURS ILEAGE ILEAGE EALER ALIDATION EALER ALIDATION P&A C P&A C RO#: RO#: OURS OURS ILEAGE ILEAGE EALER ALIDATION EALER ALIDATION P&A C P&A C RO#: RO#: OURS...
Page 578 Scheduled Maintenance EALER ALIDATION EALER ALIDATION P&A C P&A C RO#: RO#: OURS OURS ILEAGE ILEAGE EALER ALIDATION EALER ALIDATION P&A C P&A C RO#: RO#: OURS OURS ILEAGE ILEAGE EALER ALIDATION EALER ALIDATION P&A C P&A C RO#: RO#: OURS OURS ILEAGE...
Page 579 Scheduled Maintenance EALER ALIDATION EALER ALIDATION P&A C P&A C RO#: RO#: OURS OURS ILEAGE ILEAGE EALER ALIDATION EALER ALIDATION P&A C P&A C RO#: RO#: OURS OURS ILEAGE ILEAGE EALER ALIDATION EALER ALIDATION P&A C P&A C RO#: RO#: OURS OURS ILEAGE...
Page 580 Scheduled Maintenance SPECIAL OPERATING CONDITIONS If you operate your vehicle primarily in any of the following conditions, you need to perform additional maintenance as indicated. If you occasionally operate your vehicle under any of these conditions, it is not necessary to perform the additional maintenance. For specific recommendations, see your dealership service advisor or technician.
Page 581 Scheduled Maintenance Extensive idling or low-speed driving for long distances as in heavy commercial use (such as delivery, taxi, patrol car or livery) As required Change engine oil and filter as indicated by the information display and perform services listed in the Normal Scheduled Maintenance chart.
Page 582 Scheduled Maintenance Special Operating Condition Log EALER ALIDATION EALER ALIDATION P&A C P&A C RO#: RO#: OURS OURS ILEAGE ILEAGE EALER ALIDATION EALER ALIDATION P&A C P&A C RO#: RO#: OURS OURS ILEAGE ILEAGE EALER ALIDATION EALER ALIDATION P&A C P&A C RO#: RO#:...
Page 583 Scheduled Maintenance EALER ALIDATION EALER ALIDATION P&A C P&A C RO#: RO#: OURS OURS ILEAGE ILEAGE EALER ALIDATION EALER ALIDATION P&A C P&A C RO#: RO#: OURS OURS ILEAGE ILEAGE EALER ALIDATION EALER ALIDATION P&A C P&A C RO#: RO#: OURS OURS ILEAGE...
Page 584 Ford Motor Company, however, urges you to have all recommended maintenance services performed at the specified intervals and to record all vehicle service.
Page 585 Scheduled Maintenance Engine air filter & cabin air filter replacement: Engine air filter and cabin air filter life is dependent on exposure to dusty and dirty conditions. Vehicles operated in these conditions require frequent inspection and replacement of the engine air filter and cabin air filter. ENGINE COOLANT CHANGE RECORD Initial change Six years or 100000 miles (160000 km)
Page 586: Manual Heating And Air Conditioning
Index 911 Assist™ ......441, 517 Air filter, cabin ......154 All Wheel Drive (AWD), driving off road ......215 Ambient mood/lighting .....523 ABS (see Brakes) .....224 Ambulance packages ....17 Accessing and using your USB port ........495 AM/FM ........483 Accessing call history/phone Antifreeze (see Engine book during active call .....429 coolant) ........321 Accessing your calendar ..516...
Page 587 Cross Traffic Alert ....258 Cell phone use ......17 Cruise control ......242 Changing a tire ......379 Customer Assistance ....291 Changing the air filter ....337 Ford Extended Service Plan ..........399 Child safety restraints ..32, 34 Getting roadside assistance ...291 Child safety seats Getting the service attaching with tether straps ..34...
Page 588: Dual Automatic Temperature Control
Index Engine oil checking and adding ....320 Defrost .......145, 147, 149 dipstick ........320 rear window ......154 filter, specifications ....394 Dipstick refill capacities ......390 automatic transmission specifications ......390 fluid ........326–327 engine oil .........320 Event data recording ....13 Display settings ......522 Exhaust fumes ......194 Driver alert ........252 Driving under special conditions ....213, 217, 220...
Page 589 Index Instrument panel cleaning ........350 cluster ........118 Garage door opener ....179 Intelligent Access Key ....64 Gas cap (see Fuel cap) ....201 Gauges .......117–118 odometer .........128 trip odometer ......128 Jack ..........379 positioning .......379 storage ........379 Joining two calls Hazard flashers ......292 (multiparty/conference call) ..429 HD Radio™...
Page 590 Index Locks autolock ........79 Pairing other phones ..426, 503 childproof ........38 Pairing your phone ....502 doors ..........76 Pairing your phone for the first Lubricant specifications ...390 time ........425, 502 Lug nuts ........387 Parental MyKey programming ...71 Park Assist ........233 Parking brake ......224 Making and receiving calls ..503 Parts (see Motorcraft®...
Page 591: Rear Window Defroster
Index Push button start system ..190 Putting a call on/off hold ..429 Safety Belt Maintenance ....49 Safety belts (see Safety restraints) ......41, 44 Quick touch buttons ....545 Safety defects, reporting ..304 Safety information ....421, 473 Safety restraints ....41–42, 44 Belt-Minder® ......45 Radio ......404, 409–410 Belt-Minder®, AM/FM ........483...
Page 592 Index memory seat .....66, 163 Starting your vehicle ....191 jump starting ......294 second row seats ....167 push button start system ..190 third row seats ..169, 174, 176 Steering wheel ......93 Second-row power fold seat ..172 controls ........95 SecuriCode keyless entry tilting ........93–94 system ..........85 Supplemental Restraint System...
Page 593: Wrecker Towing
Index snow tires and chains ....374 spare tire .........379 terminology ......360 Vehicle health report ..443, 519 tire grades .......359 Vehicle Identification Number treadwear ......359, 368 (VIN) ..........395 Touchscreen features Vehicle loading ......270 (climate) ........533 Ventilating your vehicle ...194 Towing .......278, 285–286 Voice commands in media recreational towing ....286 mode ..........450...

Ford EXPLORER 2014 Owner's Manual

Table of Contents

Table of Contents

Table of Contents

Table of Contents

Introduction

Child Safety

Safety Belts

Personal Safety System

Supplementary Restraints System

Keys and Remote Control

Mykey

Wipers and Washers

Windows and Mirrors

Instrument Cluster

Seats

Universal Garage Door Opener (if Equipped) 179

Auxiliary Power Points

Storage Compartments

Quick Links

Troubleshooting

Related Manuals for Ford EXPLORER 2014

Summary of Contents for Ford EXPLORER 2014