Advertisement
Available languages
Available languages
Installation
Instructions
GROUNDING
INSTRUCTIONS (Cont.)
Do not modify the plug provided with the appliance. If it
will not fit the outlet, have a proper outlet installed by a
qualified electrician.
B.For permanently connected appliance:
This appliance must be connected to a grounded,
metal, permanent wiring system, or an equipment-
grounding conductor must be run with the circuit
conductors and connected to the equipment ground-
ing terminal or lead on the appliance.
CONNECTING
APPLIANCE USING 4-WIRE
CONNECTION
(MUST BE USED FOR
MOBILE HOME INSTALLATION)
NOTES:Since January 1,1996, the National Electric code
requires that the new constructions
utilize a 4-wire
connection
to an
electric
dryer.
WARNING:only a4-conductor
cord shall
be used when theappliance isinstalled ina location
where groundingthroughthe neutral conductoris
prohibited. Groundingthroughthe neutral isprohibited
forthenew branch-circuit
installations,
mobilehomes,
recreational vehicles, and areaswhere local codes
prohibit g roundingthroughtheneutral conduction.
REHOVE GROUND STRAP
ANDDISCARD KEEPGREEN
GROU N D SCRE[Fd F6"/
WIRE
RELOCATE GREEN
GROUND
SCREW
"__
HERE
GREEN
OR
RELIEF
BRACKET
COVER
HOT
WIRE
3/4",UL
/_
RECOGNIZED
STRAIN RELIEF
4 #10AWG MINIMUM C OPPER
CONDUCTORS
OR 120/240V 30APOWER
SUPPLY CORD K ITMARKED
FOR USE
WFHDRYERS
& PROVIDED
WITH
CLOSED LOOP O R SPADE TERMINALS
WFHUPTURNED
ENDS ( NOT SUPPLIED)
1. Turn off the circuit breaker (s)(30 amp) or remove the
dryer's circuit fuse at the electrical box.
2. Be sure the appliance cord is unplugged from the wall
receptacle.
3. Remove the power cord cover located at the lower
back.
4. Remove and discard ground strap. Keep the green
ground screw for step 7.
5. Install 3/4 in. UL recognized strain relief to power cord
entry hole. Bring power cord through strain relief.
6. Connect power cord as follows:
A. Connect the 2 hot lines to the outer screws of
the terminal block (marked L1 and L2).
B. Connect the neutral (white) line to the center of
the terminal block (marked N).
7. Attach ground wire of power cord with the green
ground screw (hole above strain relief bracket). Tighten all
terminal block screws (3) completely.
8. Properly secure power cord to strain relief.
9. Reinstall the cover.
WARNING:
NEVER LEAVE THE
COVER OFF OF THE TERMINAL BLOCK.
CONNECTING
DRYER USING 3-WIRE
CONNECTION
GREEN
GROUND
GROUND STRAP
SCREW
HOT
WIRE
STRAIN RELIEF
BRACKET
3/#',UL
RECOGNIZED
RELIEF
NEUTRAL
(White)
HOT
WIRE
] #10 AWGMINIMUM COPPER
COVER
CONDUCTORS
OR120/240V 30APOWER
SUPPLY C ORD KITMARKED F OR USE
WITH DRYERS
&PROVIDED
WITH CLOSED
LOOP ORSPADE T ERMINALS
WITH
UPTURNED
ENDS (NOT S UPPLIED).
1.Turn off the circuit breaker(s) (30 amp) or remove the
dryer's
circuit fuse at the electrical box.
2. Be sure the dryer cord is unplugged from the wall.
3. Remove the power cord cover located at the lower
back.
4. Install 3/4 in. UL recognized strain relief to power cord
entry hole. Bring power cord through strain relief.
5. Connect power cord as follows:
A. Connect the 2 hot lines to the outer screws of
the terminal block (marked L1 and L2).
B.Connect the neutral (white) line to the center of
the terminal block (marked N).
6. Be sure ground strap is connected to neutral (center)
terminal of block and to green ground screw on cabinet
rear. Tighten all terminal block screws (3) completely.
7. Properly secure power cord to strain relief.
8. Reinstall the cover.
A ,.0^...,,.,.-
JI, W/AKI_III_IIJ:
NEVER
LEAVE THE
COVER
OFF OF THE TERMINAL
BLOCK.
5
Advertisement
