Denon AVR-2112CI Owner's Manual page 93

Audio Setup
Make settings for audio playback.
Setting items
2ch Direct/Stereo Setting : Select the method for setting the speakers used in the 2-channel
Select the method for direct and stereo playback modes.
setting the speakers used Basic : The settings at "Speaker Setup" (vpage 86) are applied.
in the 2-channel direct and Custom : Make separate settings for 2-channel. Make the following
stereo playback modes. settings:
Front : Set the front speaker size.
Large : Use a large speaker that can adequately play back low
frequencies.
Small : Use a small speaker that has inadequate playback capacity for
low frequencies.
If "Speaker Config." – "Subwoofer"
the setting is automatically set to "Large".
SW : Set the presence of a subwoofer.
Yes : Use a subwoofer.
No : Select when a subwoofer is not connected.
If "Speaker Config." – "Subwoofer"
the setting is automatically set to "No". If the "Front" setting is
"Small", the setting is automatically "Yes".
SW Mode : Select low range signals to be reproduced by subwoofer.
LFE : When the "2ch Direct/Stereo" – "Front" setting is set to "Large",
the LFE signal alone is output from the subwoofer. Also, when the "2ch
Direct/Stereo" – "Front" setting is set to "Small", the front channel low
range signal is added to the LFE signal output from the subwoofer.
LFE+Main : The front channel low range signal is added to the LFE signal
output from the subwoofer.
This setting can be set made "2ch Direct/Stereo" – "SW" is set to
"Yes".
Crossover : Set the maximum frequency of the bass signal output from
each channel to the subwoofer.
40Hz / 60Hz / 80Hz / 90Hz / 100Hz / 110Hz / 120Hz / 150Hz / 200Hz /
250Hz
This setting can be set made "2ch Direct/Stereo" – "SW" is set to
"Yes".
If the "2ch Direct/Stereo" – "Front" setting is "Large" and the "SW
Mode" setting is "LFE", "Full Band" is displayed and the setting cannot
be made.
Default settings are underlined.
Setting details
(vpage 86) is set to "No",
(vpage 86) is set to "No",
Setting items
2ch Direct/Stereo Distance FL / Distance FR : Select the speaker.
(Continued) 0.0ft – 60.0ft (12.0ft) / 0.00m – 18.00m (3.60m) : Set the distance to
the speaker.
Set the difference in the distance between the speakers to less than
20.0 ft (6.00 m).
Level FL / Level FR : Select the speaker.
–12.0dB – +12.0dB (0.0dB) : Adjust the level of each channel.
Auto Surround ON : Memorize settings. Automatically play with the last used surround
Make setting for mode.
memorizing surround mode OFF : Do not memorize settings. Surround mode does not change
setting for each input signal according to input signal.
type.
The auto surround mode function lets you store in the memory the
surround mode last used for playing the four types of input signals listed
below.
q Analog and PCM 2-channel signals
w Dolby Digital and DTS 2-channel signals
e Dolby Digital and DTS multi-channel signals
r LPCM Multi-channel signals
When playing in PURE DIRECT, the surround mode does not change
even if the input signal is changed.
EQ Customize Audyssey Byp. L/R : Set when not using "Audyssey Byp. L/R" equalizer.
Set the disengaged Used : Use.
equalizers to not display Not Used : Do not use.
when the "MultEQ ® XT" is
Set so that "Audyssey Byp. L/R" settings can be made when
selected.
Audyssey ® Auto Setup is performed.
Audyssey Flat : Set when not using "Audyssey Flat" equalizer.
Used : Use.
The equalizer mode in which
Not Used : Do not use.
"Not Used" is selected
Set so that "Audyssey Flat" settings can be made when Audyssey ®
cannot be stored and
recalled in the Quick Select
Auto Setup is performed.
function.
Manual : Set when not using the "Manual" equalizer.
Used : Use.
Not Used : Do not use.
90
System Setup
Setting details