Pioneer AVIC-HD1BT Operation Manual page 175

MAN-HD1BT-SOFTW-EN.book Page 173 Thursday, April 20, 2006 3:47 PM
Message
The vertical installation angle is
changed. Gyro Sensor calibration is
re-initialized.
Excess vertical installation angle
detected. Please install the naviga-
tion unit correctly.
Route calculation was not possible.
Route calculation not possible
because destination is too far.
Route calculation not possible
because destination is too close.
Route calculation not possible due to
traffic regulations.
Route calculation not possible
because navigation cannot be pro-
vided around destination or starting
point.
Route to destination cannot be cal-
culated.
• Ferry could not be avoided.
• Toll roads could not be avoided.
• Motorway could not be avoided.
• Ferry, toll roads and motorways
could not be avoided.
• Ferry and toll roads could not be
avoided.
• Toll roads and motorways could not
be avoided.
• Ferry and motorway could not be
avoided.
This area does not contain any POI's
of the selected type.
Failed to make the route profile.
There is no Traffic List.
"Service provider name" is currently
unavailable.
When
If the mounting angle of the naviga-
tion unit has been changed.
The navigation system is installed
with an extreme angle exceeding the
limitation of the installation angle.
Route calculation has failed because
of malfunction of map data, software,
hardware.
If the destination is too far.
The destination or waypoint(s) are
too close.
• The destination or waypoint(s) are
in a Control Traffic Zone (CTR) and
the route calculation is hampered.
• Your vehicle is currently in a Con-
trol Traffic Zone (CTR) and the
route calculation is hampered.
The destination, waypoint(s), or start-
ing point are in an area where no
road exists (e.g. a mountain) and the
route calculation is impossible.
The destination or waypoint(s) are in
an isolated island, etc. without a ferry
and the route calculation is impossi-
ble. If there is no road connect to
your starting point or destination,
this message will appear.
In case a ferry route, toll roads or
motorways are included in the route
to the destination or waypoints even
though a route is set to avoid them.
You can recognise these condition by
icon.
"Checking and modifying the
route" Page 24
Facilities of the selected category do
not exist in the surrounding areas.
In rarely case the route calculation
error may occur.
There is no available traffic informa-
tion now.
The system cannot tune to the
selected provider for some reason.
What to do
The system initialises the sensor in
order to operate it with the maximum
performance and automatically
starts re-learning.
Confirm the installation angle. (The
navigation system must be installed
within the allowed installation angle.
For details, refer to Installation Man-
ual.)
• Change the destination.
• Consult the Pioneer Local dealer if
this message persists.
• Set a destination closer to the start-
ing point.
• Set one or more waypoints.
Set a destination and waypoint(s) far-
ther from the starting point.
• Set a destination and waypoint(s)
outside the CTR if you know where
the restricted area is.
• Try the destination or waypoint(s)
away from the currently set points
to some extent.
• Drive your vehicle to an unre-
stricted area and reset the destina-
tion and waypoint(s).
• Set a destination and waypoint(s)
on roads.
• Reset the destination after you
drive the vehicle to any road.
Change the destination.
If the current route is not desired, set
destination or waypoints that do not
pass through a ferry route, toll roads
or motorways.
Use another search method or move
to another location and perform the
[Vicinity Search] again.
• Retry.
• Consult the Pioneer Local dealer if
this message persists.
Move to the location where you can
receive the RDS-TMC information,
and then try the operation again.
• Select another provider.
• Move to the location where you can
receive the selected provider, and
then try the operation again.
173