Liquid Propane Cylinder Requirements - Weber Summit Series Installation And Owner's Manual

12
• Do not use a damaged LP cylinder. Dented or rusty LP cylinders or LP cylinders
with a damaged valve may be hazardous and should be replaced with a new
one immediately.
Liquid Propane (LP) Cylinder(s)
• The joint where the hose connects to the LP cylinder must be leak tested each
time the LP cylinder is reconnected. For example, test each time the LP cylinder
is refilled.
• Be sure the regulator is mounted with the small vent hole pointed downward so
that it will not collect water. This vent should be free of dirt, grease, bugs etc.
• The gas connections supplied with your Weber
designed and tested to meet 100% CSA and ANSI requirements.
PROBLEM
Burners do not light.
Flame is low in HIGH position.
Burners do not light -or- burners have a small flickering
flame in the HIGH position -or- barbecue temperature
only reaches 250˚ to 300˚F in the HIGH position.
If problems cannot be corrected by using these methods, please contact the Customer Service Representative in your area using the contact information on our
web site. Log onto www.weber.com
©2005- The following trademarks are registered in the name of Weber-Stephen Products Co., an Illinois corporation, located at 200 East Daniels Road, Palatine, Illinois 60067 U.S.A.
Australia; Smokey Joe, Weber, Kettle Silhouette , Genesis, Austria; Kettle Silhouette , Smokey Joe, Weber, Benelux; Kettle Silhouette , Smokey Joe, Weber, Compact Grill Configura-
tion, Botswana; Weber, Canada; Smokey Joe, Genesis, China; Kettle Silhouette , Denmark; Kettle Silhouette , Smokey Joe, Weber, Finland; Smokey Joe, France; Kettle Silhouette ,
Smokey Joe, Weber, One-Touch, Germany; Smokey Joe, Weber, One-Touch, Greece; Smokey Joe, Ireland; Kettle Silhouette , Smokey Joe, Italy; Smokey Joe, Weber, Japan; Smokey
Joe, Weber, Korea; Smokey Joe, Weber, New Zealand; Weber, Smokey Joe, Nigeria; Weber, Norway; Smokey Joe, Weber, Portugal; Weber, South Africa: Smokey Joe, Weber, Kettle
Configuration, Spain; Smokey Joe, Weber, Sweden; Kettle Silhouette , Smokey Joe, Switzerland; Kettle Silhouette , Smokey Joe, Weber, United Kingdom; Smokey Joe, Weber, Weber
One-Touch, U.S.A..; Kettle Configuration, Kettle Silhouette , Smokey Joe, Weber, One-Touch, Firespice, Go-Anywhere, U.S.A.;Kettle Configuration, Kettle Silhouette, Genesis, Fla-
vorizer, Crossover, Flamgo, Performer, Rapidfire, Tuck 'N Carry, Jumbo Joe, Bar-B-Kettle, Master-Touch, Spirit, Grill Out, Summit, Platinum, 1-800-Grill-Out, Ranch, Matchless Flame,
Zimbabwe; Weber, Kettle Configuration, Kettle Silhouette .
GAS INSTRUCTIONS
® gas barbecue have been
DOT 4BA240
00/07
TANK CABINET TROUBLESHOOTING
Is gas supply off?
Is fuel hose bent or kinked?
The excess flow safety device, which is part of
the barbecue to cylinder connection, may have
activated.
® .
WEBER-STEPHEN PRODUCTS CO.
Printed in USA.
WARNING: Replacement LP tanks must match the regulator
connection supplied with this barbecue.

LIQUID PROPANE CYLINDER REQUIREMENTS

• Check to be sure cylinders have a D.O.T. certification (1), and date tested (2) is
within five years. Your LP gas supplier can do this for you.
• All LP tank supply systems must include a collar to protect the cylinder valve.
• The LP cylinder must be a 20-lb. size approximately (18¼ inches high, 12¼
inches in diameter).
• The cylinder must be constructed and marked in accordance with the
Specifications for LP - Gas Cylinders of the U.S. Department of Transportation
(D.O.T.) or the National Standard of Canada, CAN/CSA-B339, Cylinders,
Spheres and Tubes or Transportation of Dangerous Goods; and Commission, as
1 applicable.
IN CANADA
LIQUID PROPANE CYLINDER REQUIREMENTS
Note: Your retailer can help you match a replacement tank to your barbecue.
• The LP cylinder must be constructed and marked in accordance with the
specifications for LP gas cylinders, T.C.
2
CHECK
www.weber.com ®
CURE
Turn supply on.
Straighten fuel hose.
To reset the excess flow safety device turn all burner control
knobs and the cylinder valve OFF. Disconnect the regulator
from the cylinder. Turn burner control knobs to HIGH. Wait at
least 1 minute. Turn burner control knobs OFF. Reconnect
the regulator to the cylinder. Turn cylinder valve on slowly.
Refer to "Lighting Instructions" .
WWW.WEBER.COM
®