Weber Summit Series Service Manual
Rear vent assembly replacement instructions
Hide thumbs
Also See for Summit Series:
- Owner's manual (74 pages) ,
- Installation and owner's manual (45 pages) ,
- Manual (36 pages)
Advertisement
Quick Links
THIS PROCEDURE SHOULD ONLY BE PERFORMED BY AN AUTHORIzED
WARNINg: gENUINE WEBER-STEPHEN REPLACEMENT PARTS MUST BE USED FOR ANY REPAIR OR REPLACEMENT.
YOUR ACTIONS, IF YOU FAIL TO FOLLOW THIS PRODUCT WARNINg, MAY CAUSE A FIRE, AN ExPLOSION, OR
STRUCTURAL FAILURE RESULTINg IN SERIOUS PERSONAL INjURY OR DEATH AS WELL AS DAMAgE TO PROPERTY.
DANgER: BEFORE PERFORMINg ANY WORk MAkE SURE THE gAS SUPPLY IS TURNED OFF AT THE SOURCE.
FAILURE TO FOLLOW DANgERS, WARNINgS AND CAUTIONS CONTAINED IN THIS INSTRUCTION SHEET MAY CAUSE A
FIRE OR AN ExPLOSION RESULTINg IN SERIOUS PERSONAL INjURY OR DEATH AS WELL AS DAMAgE TO PROPERTY.
BEFORE STARTINg:
Make sure lid is closed
and casters are locked to
prevent grill from moving.
1
DiScOnnectiOn OF GaS SOURce
A) Make sure main gas source is completely turned off.
B) Located inside tank enclosure, disconnect main corrugated gas line from
bulkhead fitting, (1).
C) Pull main corrugated gas line through
island structure cavity and into grill
assembly. (Not Pictured)
1
WEBER-STEPHEN PRODUCTS LLC SERVICE TECHNICIAN
(Will vOid all WarraNTy prOTEcTiON.)
ReaR
FilleR StRip
Replacement
NOTE: Grills illustrated may have slight differences than model purchased.
REAR VENT ASSEMBLY
REPLACEMENT INSTRUCTIONS
ReaR
Vent
Replacement
2
A) Remove all front, side, and rear filler strips.
1
Vent bRacket
Replacement
FilleR StRip RemOVal
56589 10/30/11
ReaR
AA
Advertisement
Related Manuals for Weber Summit Series
Summary of Contents for Weber Summit Series
- Page 1 THIS PROCEDURE SHOULD ONLY BE PERFORMED BY AN AUTHORIzED WEBER-STEPHEN PRODUCTS LLC SERVICE TECHNICIAN WARNINg: gENUINE WEBER-STEPHEN REPLACEMENT PARTS MUST BE USED FOR ANY REPAIR OR REPLACEMENT. YOUR ACTIONS, IF YOU FAIL TO FOLLOW THIS PRODUCT WARNINg, MAY CAUSE A FIRE, AN ExPLOSION, OR STRUCTURAL FAILURE RESULTINg IN SERIOUS PERSONAL INjURY OR DEATH AS WELL AS DAMAgE TO PROPERTY.
- Page 2 RemOVal OF ReaR Vent RemOVal FROnt WHeel aliGnment panel TOOLS NEEDED: - PHILLIPS TOOLS NEEDED: - PHILLIPS A) Using a Phillips head screwdriver, remove screws that secure rear vent to rear vent bracket (1). A) Using a Phillips head screwdriver, remove screws that secure front wheel B) Lift rear vent off grill assembly (2).
-
Page 3: Rear Vent Installation
• REPLACEMENT PART INSTALLATION GRill aSSemblY ReinStallatiOn ReaR Vent bRacket inStallatiOn A) Push grill assembly into island structure. B) Align each front caster so that v-shaped piece faces forward. Reach behind TOOLS NEEDED: - PHILLIPS each caster and push lock down. (Not Pictured) A) Place rear vent bracket onto frame assembly hooks (1). - Page 4 cOnnectiOn OF GaS SOURce FilleR StRip inStallatiOn A) Install all front, side, and rear filler strips. A) Make sure main gas source is completely turned off. B) Pull main corrugated gas line through grill assembly into island structure cavity. (Not Pictured) C) Connect main corrugated gas line to bulkhead fitting, which is located inside tank enclosure (1).
- Page 5 Contact the Customer Service Representative in your area using the contact information on our web site. Log onto www.weber.com ® E) LP: Hose-to-regulator connection (3).
- Page 6 WARNINg: All repairs to gas carrying, gas burning, igniter or structural components must be performed by an authorized Weber-Stephen Products LLC service technician. These parts may be gas carrying, gas burning, igniter or structural components. Please contact Weber-Stephen Products LLC, Customer Service Department for genuine Weber-Stephen Products LLC replacement part(s) information.
- Page 7 Visit Visit For All of Your For All of Your Grilling Needs Grilling Needs...
- Page 8 WEBER-STEPHEN PRODUCTS LLC Customer Service Center 1890 Roselle Road, Suite 308 Schaumburg, IL 60195 1-800-446-1071 (USA ONLY) www.weber.com ®...