The Installation Space; Dimensions And Clearances; Step8, Adjust Door Swing - GE 36" Built-In Bottom-Freezer Installation Instructions Manual

Design Guide
THE INSTALLATION SPACE
35-1/2'
Finished Width
The finished 1' [xc
cutout width [ [ _2-5/16"
must be [ 11 '_=T .
[ 1[
10" _-Electrieal
84-1/21 max_ Area
83-t/2 min
IL_24" CutoutDepth
Finished
) I
Opeoing II
5"
...........
Wall View
75" From
FloortoBottom
of Electrical A rea
2
Water And Electrical Locations
Electrical and water supply must be located as shown.
The cutout depth must be 24"
The refrigerator will project forward, slightly beyond
adjacent cabinetry, depending on your installation.
Cutout depth beneath a soffit:
When installed beneath a soffit, the soffit cannot
exceed the 24" installation depth shown. The top case
trim overlaps the bottom of the soffit.
Additional Specifications
• A 115 volt 60Hz., 15 or 20 amp power supply is
required. An individual properly grounded branch
circuit or circuit breaker is recommended. Install
a properly grounded 3-prong electrical receptacle
recessed into the back wall. Electrical must be
located on rear wall as shown.
Note: GFI (ground fault interrupter) is not
recommended.
• Water line can enter the opening through the
floor or back wall. Route GE SmartConnect
TM
kit or
1/4" O.D. copper tubing between the cold water
line and the water connection location. The tubing
should be long enough to extend to the front of the
refrigerator. Installation of an easily accessible
shut-off valve in the water line is required.
DIMENSIONS AND CLEARANCES
35" 25-3/8'Framed Models
CaseWidth 25-3/4'StainlessSteelModels
From
"83-1 Floorto
at Top Frame
I
}6"Frame to
Frame Width
Depth Includin Handles:
26-7/8' Frame_ Models
27-3/4"Staintess SteelModels
28-11/16'professional StyleModels
* Shipping height.The
refrigerator c anbe adjusted
to fit into a cutoutthat is
83-1/2"min.to 84-1/2'max.
height.Notethat the top
casetrim atthe front is
1/2" higherandwill ovedap
uppercabinetryor soffit
Uselevelinglegsandwheels
for a maximum 1" height
adjustment
Product Clearances
These refrigerators are equipped with a 2-position door
stop. The factory set 130 ° door swing can be adjusted to
90 ° if clearance to adjacent cabinets or walls is restricted.
\
130"
2Y3.7/8
9O" Door S wing ,Fra_eBehmd
-3/4"
90" Ill "4" Stainless
_---[_L[ andFramed
models.
_1_ 5"ProSeries
•Min.Distance toWall
Allow 25" minimum clearance for a full 130 ° door
swing. Allow 15" for pan removal.
For a 90 ° door swing, allow 4" min. clearance to a
wall, for framed and stainless steel models. Allow 5"
min. clearance for professional style models. If the
90 ° door stop position is used, pan access is maintained,
but pata removal is restricted.
See illustrations pages 4 and 5 to determine door swing
interaction with adjacent cabinets or countertops.
ZUG2, ZUGSS2 Unified Grille Panel Kit
• If you are installing two refrigerators, side by side,
the installation space must be 71-1/2" wide.
Note: Additional cutoutwidth may be required whenside panels
are used,Addside panelthicknessto the finished cutoutto
calculaterough-in width.
• The water and electrical locations for each product
must be located as shown.
• A separate 115V, 60Hz., 15 or 20 amp power supply
is recommended for each product.
84-1/2"max
83-1/Tmin
Finished
Opening
3-1/2"
75"From
Floor to Bottom
of Electrical Area
3-1/2"
3