Authorisation

forgot your password?
Manuals → Brands → GE → Refrigerator → B420DX → Specification sheet

GE B420DX Specification Sheet

Ge monogram built-in side-by-side refrigerator specification sheet.

Download Manual (7 pages, 0.24 Mb) Add to your account Write a comment Upload Manual
1 2 3 4 5 6 7
 
ZISW/B420DX
GE Monogram
Water Filter
Dimensions and Installation Information (in inches)
41"
25-3/8
Case Width
*83-1/2"
at
Rear
42"
26-7/8"
Frame to Frame
including
handle
Product Clearances
These refrigerators are equipped with a 2 position door stop.
The factory set 130° door swing can be adjusted to 90° if
clearance to adjacent cabinets or walls is restricted.
130° Door Swing
13"
19"
Allow minimum clearances for freezer door and fresh food
door for a full 130° door swing and to allow for pan removal.
4" minimum clearance is required when door swing is
adjusted to 90° . If the 90° door stop position is used, pan
access is maintained, but pan removal is restricted.
Installation Information: Before installing, consult
installation instructions packed with product, or online
at Monogram.com, for current dimensional data.
For answers to your Monogram,
®
or GE
appliance questions, visit our website
at ge.com or call GE Answer Center
800.626.2000.
®
42" Built-In Side-by-Side Refrigerator with Dispenser and
* Shipping height.
The refrigerator
can be adjusted to
fit into a cutout that
is 83-1/2" min. to
*84" From
84-1/2" max. height.
Floor to
Note that the top
Top Frame
case trim at the
front is 1/2" higher
and will overlap
upper cabinetry or
soffit. Use leveling
legs and wheels
for a maximum 1"
height adjustment.
90° Door Swing
®
™
GE Profile
®
service,
The Installation Space
84-1/2" max
83-1/2" min
Finished
Opening
Water and electrical locations
The opening must be prepared with the electrical and water
supply located as shown.
The cutout depth must be 24" .
The refrigerator will project forward, slightly beyond
23-7/8"
adjacent cabinetry, depending on your installation.
Behind
Frame
The cutout depth beneath a soffit:
When installed beneath a soffit, the soffit cannot exceed the
24" installation depth shown. The top case trim overlaps the
28-5/8"
bottom of the soffit.
Additional Specifications
• A 115 volt 60Hz., 15 or 20 amp power supply is required.
4" Min.
to Wall
An individual properly grounded branch circuit or circuit
breaker is recommended. Install a properly grounded 3-
prong electrical receptacle recessed into the back wall.
Electrical must be located on rear wall as shown.
Note: GFI (ground fault interrupter) is not recommended.
• Water line can enter the opening through the floor or back
wall. The water line should be 1/4" O.D. copper tubing or
GE SmartConnect
water connection location, long enough to extend to the
front of the refrigerator. Installation of an easily accessible
shut off valve in the water line is recommended.
36" Models 12"
42" Models 18"
48" Models 20"
*Finished Width
6"
Electrical
Area
5"
75" From Floor
24"
5"
5"
Water Supply
3-1/2"
3-1/2"
696Dia15
™
kit between the cold water line and
Listed by
Underwriters
Laboratories
Specification Created 3/08
to Bottom
of Electrical
Area
®
As an EnErgy StAr
partner, gE has determined
that this product meets the
EnErgy StAr guidelines
for energy efficiency.
110172
Next page ->

Related Manuals for GE B420DX

This manual also for: Zisw

Summary of Contents

  • Page 1

    For answers to your Monogram, GE Profile ® or GE appliance questions, visit our website ® at ge.com or call GE Answer Center 800.626.2000. The Installation Space * Shipping height. The refrigerator can be adjusted to fit into a cutout that is 83-1/2"...

  • Page 2

    GE Profile ® or GE appliance questions, visit our website ® at ge.com or call GE Answer Center 696Dia2 800.626.2000. Door Handles The supplied handles can be adjusted to accommodate both framed or overlay panels. Custom handles of your choice, supplied by your cabinet maker, can also be installed.

  • Page 3

    GE Profile ® or GE appliance questions, visit our website 194Dia_64 ® at ge.com or call GE Answer Center 800.626.2000. 194Dia_63 Raised Overlay Panel Design On Dispenser Models When a raised panel design is to be used, a custom wide Door middle rail is required to accept the dispenser trim.

  • Page 4

    For answers to your Monogram, GE Profile ® or GE appliance questions, visit our website ® at ge.com or call GE Answer Center 800.626.2000. Dispenser Models These refrigerators are supplied with two dispenser trims, 5/16" one for framed panels and one for overlay panels.

  • Page 5

    1.100" thickness. ® For answers to your Monogram, GE Profile ® or GE appliance questions, visit our website ® at ge.com or call GE Answer Center 800.626.2000. 23-7/8" From Rear of Refrigerator Case Trim 1/2" 1/4"...

  • Page 6

    1.100" thickness. ® For answers to your Monogram, GE Profile ® or GE appliance questions, visit our website ® at ge.com or call GE Answer Center 800.626.2000. Refrigerator Door ™ service, Case Trim 23-7/8" From Rear of Refrigerator 1/4"...

  • Page 7

    • Model ZISB420DX – Black dispenser ® For answers to your Monogram, GE Profile ® or GE appliance questions, visit our website ® at ge.com or call GE Answer Center 800.626.2000. ™ service, ZISB420DR As an EnErgy StAr Listed by partner, gE has determined...

Comments to this Manuals

Symbols: 0

Latest comments:

×

Select the desired size and copy embed code

Copy your embed code and put on your site: