Ipod Or Iphone Playback - Sharp XL-HF200P (BK Operation Manual

Listening to the iPod or iPhone (continued)
To remove iPod or iPhone adaptor
Insert the tip of a screwdriver ("-" type, small)
into the adaptor hole as shown and lift upward
to remove.

iPod or iPhone playback

1
Press the ON/STAND-BY button to turn the power on.
2
Press the iPod/iPhone button on the remote control or Function
button repeatedly on the main unit to select iPod function.
3
Insert iPod or iPhone unit in iPod dock of main unit.
4
Press the (iPod/iPhone
iPhone playback
Sound will only switch from iPhone to the main unit after
authentication process is completed in approximately 10 seconds.
Incoming calls will pause the playback and iPhone ringtones will be
heard from the main unit speakers only.
Once the calls are answered, the conversation can only be heard
through the built-in iPhone speaker. Turn on the iPhone speaker or
undock the iPhone to start conversation.
To disconnect iPod or iPhone
Simply remove the iPod or iPhone from the iPod dock. It is safe to do so
even during playback.
Navigating the iPod and iPhone menus
1
Press the MENU button to view the menu on iPod or iPhone unit.
Press it again to go back to previous menu.
2
Use the PRESET ( or
and then press ENTER button.
Note:
When navigating the iPod or iPhone menu with remote control, do not
operate any of the buttons on the iPod or iPhone unit. The volume level
is adjusted by pressing the VOL (+ or -) button on the main unit or the
remote control. Adjusting the volume on the iPod and iPhone units give
no effect.
iPod and iPhone operations:
The operations described below depend on the generation iPod and
iPhone you are using.
System on operation:
When the main unit is powered on, the iPod and iPhone units will
automatically power on when docked in the unit.
System off (stand-by operation):
When the main unit is turned to stand-by mode, the docked iPod and
iPhone unit will automatically turn to stand-by mode.
) button to start playback.
RRMCGA232AWSA
) button to select an item on the menu
Watching videos on a TV connected to iPod
or iPhone
1
Press the DISPLAY (TV OUT) button for more than 2 seconds. "TV
Display" will appear on display.
2
Press the ENTER button to start playback.
Notes:
If the TV Out setting is already turned on at video menu, the video
is automatically displayed on the TV screen when ENTER key is
pressed.
To return to watching video on iPod or iPhone screen, press the
MENU button to enter video menu. Then press the DISPLAY (TV
OUT) button for more than 2 seconds until "iPod Display" appears.
During iPod or iPhone video playback, pressing the DISPLAY (TV
OUT) button will not toggle video out display between iPod and TV.
iPod or iPhone playback detection function:
Once the play button on the iPod or iPhone unit is pressed, the main
unit will automatically change to iPod function overriding the previous
function selected.
Caution:
Unplug all accessories for the iPod or iPhone before inserting it into
the iPod dock.
Stop button ( ) at main unit is invalid during iPod function.
Various iPod functions
Function Main unit
Play
Pause
Track
up/down
Fast
forward/
reverse
Display
____
Repeat
____
Shuffl e
____
iPod
____
Menu
iPod
Enter
____
iPod
Cursor
____
Up/Down
E-5
Remote
Operation
control
Press in the pause mode.
Press in the playback mode.
Press in the playback or pause
mode. If you press the button
in the pause mode, press the
button to start the desired
track.
Press and hold down in the
playback mode.
Release the button to resume
playback.
iPod back light ON.
Press for more than 2 seconds
to toggle the video out display
between iPod or TV.
Press to toggle repeat mode.
Press and hold down to toggle
shuffl e mode.
Press to view the iPod menu
during iPod function.
Press to confi rm the selection.
Press to select the iPod menu.