Timer And Sleep Operation (Remote Control Only) - Sharp XL-HF200P (BK Operation Manual

Listening to the radio
To scan the preset stations
The stations saved in the memory can be scanned
automatically. (Preset memory scan)
1
Press the PRESET (
0.5 seconds. The preset number will fl ash and the
programmed stations will be tuned in sequentially, for
5 seconds each.
2
Press the PRESET (
desired station is located.
To erase entire preset memory
1
Press the ON/STAND-BY button to enter the stand-by
mode.
2
Whilst pressing down the FUNCTION button, press the
ON/STAND-BY button until "Tuner Clear" appears.
FUNCTION ON/STAND-BY
Setting the clock (Remote control only)
In this example, the clock is set for the 12-hour (AM 12:00)
display.
1
Press the ON/STAND-BY button to turn the power on.
2
Press the CLOCK/TIMER button.
3
Within 10 seconds, press the ENTER button. To adjust
the day, press the
ENTER button.
4
Press the or button to select 24-hour or 12-hour
display and then press the ENTER button.
The 12-hour display will appear.
(AM 12:00 - PM 11:59)
The 12-hour display will appear.
(AM 00:00 - PM 11:59)
The 24-hour display will appear.
(00:00 - 23:59)
5
To adjust the hour, press the
press the ENTER button. Press the
once to advance the time by 1 hour. Hold it down to
advance continuously.
6
To adjust the minutes, press the
then press the ENTER button. Press the
button once to advance the time by 1 minute.
To confi rm the time display:
Press the CLOCK/TIMER button. The time display will
appear for about 5 seconds.
(continued)
or ) button for more than
or ) button again when the
or button and then press the
or button and then
or
or button and
Note:
When power supply is restored after unit is plugged in
again or after a power failure, reset the clock (page 10).
To readjust the clock:
Perform "Setting the clock" from step 1. If the "Clock" does
not appear in step 2, step 4 (for selecting the 24-hour or
12-hour display) will be skipped.
To change the 24-hour or 12-hour display:
1
Clear all the programmed contents. [Refer to "Factory
reset, clearing all memory" on page 13 for details.]
2
Perform "Setting the clock" from step 1 onwards.
Timer and sleep operation (Remote
control only)
Once timer:
Once timer play works for one time only at a preset time.
(" " indicator).
Daily timer:
Daily timer play works at the same preset time every day
that we set. For example, set the timer as a wake-up call
every morning.
("DAILY" indicator).
Using the once timer and daily timer in combination:
For example, use the once timer to listen a radio
programme, and use the daily timer to wake up.
Daily timer
Start
Timer playback
Before setting timer:
Check that the clock is set to the correct time (refer to page
10). If it is not set, you cannot use the timer function.
For timer playback: Plug in USB or load discs or dock iPod
to be played.
1
Press the ON/STAND-BY button to turn the power on.
2
Press and hold the CLOCK/TIMER button.
3
Within 10 seconds, press the
"Once" or "Daily", and press the ENTER button.
4
Within 10 seconds, press the
"Timer Set", and press the ENTER button.
5
To select the timer playback source (CD, TUNER, USB,
iPod, AUDIO IN, LINE IN), press the
Press the ENTER button.
When you select the tuner, select a station by pressing
the or
If a station has not been programmed, "No Preset" will
be displayed and timer setting will be cancelled.
6
To adjust the day, press the
button
press the ENTER button.
7
Press the ENTER button to adjust the hour. Press the
or button and then press the ENTER button.
8
To adjust the minutes, press the
or
then press the ENTER button.
9
Set the time to fi nish as in steps 7 and 8 above.
10
Adjust the volume using the VOLUME control, and
then press the ENTER button. Do not turn the volume
up too high.
E-10
1 minute or more
Once timer
Stop Start
or
or
button, and then press the ENTER button.
or
or
Stop
button to select
button to select
or button.
button and then
button and