Panasonic Toughbook CF-19KDRAXCM Service Manual page 55

n Putting of the Sheet
*Because the sheets described on this page
are waterproof sheets, the whole part should
be put pressure after attaching.
(Put pressure around the sheet in particular.)
Apply the load to attach. 30 ~ 40N (3.0 ~ 4.0 Kgf)
Attaching details of Tape
Photo
n Cautions for Setting the Keyboard
S1:Insulation S2:Bitten S3:Sharp Edge
CAUTION
S4:Part No. Check S5:Other
Insert positions of
LCD Cable/KBD FFC
Connect the Connector
to the dotted part.
To avoid
S5
wiring damage
Note
Hold the Connector
part when connecting
/ disconnecting.
Insert position
Never bend at the foot
of KBD FFC.
of stiffening plate.
Incline to the right.
Incline to the right.
Avoid running over
the Top Case.
Insert the KBD FFC.
Lock the connector
after inserting FFC.
LCD Cushion Sheet
KB CNT Hole Cushion
Fit to
the rib.
0~1mm
Fold.
Avoid coming over. Avoid coming over. Avoid coming over.
3~5mm
0~0.5mm 0~0.5mm 0~0.5mm
Avoid running over. Avoid running over. Avoid running over.
0.5~1mm 0.5~1mm 0.5~1mm
Palmrest Waterproof Sheet L
Attach it
using
Fold.
the JIG.
Attach to
the rib.
Fold over the front and attach it.
KBD CNT LID Ass'y
Confirm the LCD Rear
side is at front when
processing the wire.
Screw
Screw
Insert the KBD FFC.
KBD Ass'y
Set using the jig.
Torque of tightening screw :0.2 ± 0.02N·m( 2.0 ± 0.2kgf·cm)
Ensure it does not come
over the end of the rib.
Gasket E
0~0.5mm
The paste should
Fit to the wall of the end side, and put Fit to the wall of the end side, and put Fit to the wall of the end side, and put
be put the left side.
the surplus to the Cabinet side. the surplus to the Cabinet side. the surplus to the Cabinet side.
0~0.5mm 0~0.5mm 0~0.5mm
Tape
0~0.5mm
*Avoid running over.
0~0.5mm
Click Button Plate
0.5~1.5mm 0.5~1.5mm 0.5~1.5mm
TP Tape
Attach it using the jig.
Apply the load to attach. 30~40N(3.0~4.0Kgf)
KB CNT LID Sheet
Use the jig.
KB CNT LID
<Order of fixing screws>
Rotate the LCD to make
the LCD display face front
after setting the KBD.
Screw
KBD CNT LID Ass'y
9-32
Ensure it does not come
LCD Cushion Sheet
over the end of the rib.
Avoid running over the rib.
KBD Waterproof Sheet C
Match to the circles. Match to the circles. Match to the circles.
0~0.5mm 0~0.5mm 0~0.5mm
*Avoid running over. *Avoid running over. *Avoid running over.
0~0.5mm 0~0.5mm 0~0.5mm
Avoid running over. Avoid running over. Avoid running over.
0.5~1mm 0.5~1mm 0.5~1mm
0~0.5mm 0~0.5mm 0~0.5mm
0~0.5mm 0~0.5mm 0~0.5mm Palmrest Waterproof Sheet R
Attach it using the jig.
Fold over the front and attach it.
Attach to the inside
the groove.
Avoid running over.
Gasket
Tighten inside first.
Screw
Screw
Tighten inside first.
KBD Plate(L)
Screw
Before attaching 2 and 3, Before attaching 2 and 3, Before attaching 2 and 3,
press the two-sided tape press the two-sided tape press the two-sided tape
parts (4 positions). parts (4 positions). parts (4 positions).
:30N(3.0Kgf) :30N(3.0Kgf) :30N(3.0Kgf)
KBD Plate(R)
4 7mm
Screw