Denon AVR-1910 Owner's Manual page 25

Changing the amplifier assignment (Amp Assign)
The signals output from the AVR-1910's SURR. BACK/AMP ASSIGN
speaker terminals can be switched to signals of the surround mode
being used.
1
Press ui to select "Amp Assign".
2
Press o p to select
Amp Assign Mode.
3-1.Audyssey Auto Setup
Please place microphone
at ear height at
main listening position.
[ENT]:Select [RTN]:Back
Normal
: The sound of the surround back channel is output
from the speakers connected to the SURR.
BACK/AMP ASSIGN terminals.
ZONE2
: If the ZONE2 power is on, the sound of the
ZONE2 channel is output from the speakers
connected to the SURR. BACK/AMP ASSIGN
terminals.
Front A Bi-Amp
: The sound of the front A bi-amp channel is output
from the speakers connected to the SURR.
BACK/AMP ASSIGN terminals.
Front B Bi-Amp
: The sound of the front B bi-amp channel is output
from the speakers connected to the SURR.
BACK/AMP ASSIGN terminals.
Front Height : T he sound of the front height channel is output
from the speakers connected to the SURR.
BACK/AMP ASSIGN terminals.
n To cancel Audyssey Auto Setup
Use ui to select "Cancel" , then use o p
Step 3 : Performing the Audyssey Auto Setup Procedure
• The Audyssey Auto Setup function detects the presence of each
speaker and automatically calculates the speaker size, channel
level, distance, and optimal crossover frequency setting. Audyssey
Front
MultEQ corrects acoustical distortions within the listening area.
• Once started, MultEQ will play a series of test tones through each
speaker.
• Before starting, connect and position all of your speakers.
1
Press ui
MultEQ
"Start", then press
.
Front Sp.: A
Detection of the speaker
Amp Assign:
configuration starts.
Normal
Start
Cancel
2
Once all the speakers
have been detected
and the screen on
the right appears,
check the results
of detection of the
connected speakers.
3
Once you have checked the results, use
"Next", then press
Measurements for the main listening position begin.
4
Once the screen on
the right appears,
move the
microphone to the
second position, use
ui to select "Next",
to select "Yes" .
then press
Measurements for the second position begin.
Making the Optimum Settings for the Connected Speakers Automatically (Audyssey Auto Setup)
to select
3-1.Audyssey Auto Setup
MultEQ
Please place microphone
at ear height at
main listening position.
Front Sp.: A
Amp Assign:
Normal
Start
Cancel
[ENT]:Select [RTN]:Back
Step1:Speaker Detection
MultEQ
Front Sp. :Yes
Center Sp. :Yes
Subwoofer :Yes
Surround Sp. :Yes
S.Back Sp. :Yes
:2sp
Next
Retry
[ENT]:Next
ui
to select
.
Step2:Measurement
MultEQ
Please place microphone
setup
at ear height at
2nd listening position.
Next
Calculate
Cancel
. [ENT]:Next
5
Perform Step 4 repeatedly for the 3rd, 4th, 5th, and
6th measurments.
Once measurements for the sixth position are completed, "All
the measurements were finished. " is displayed.
b Measure at a total of six positions, including the main listening
position and positions around it. It is possible to stop the settings
with five positions or fewer, but for better results we recommend
measuring at six positions.
6
Once measurements
Step2:Measurement
are finished, use ui
All the measurements
were finished.
to select "Calculate",
then press .
Analysis begins.
[ENT]:Cancel
b Analysis takes several
minutes to complete.
The time required for
Step3:Calculation
this analysis depends on
Calculating
the number of speakers
Please wait...
connected. The greater
the number of speakers
connected, the longer
[----------]
analysis will take.
7
Use ui to select the item you want to check, then
press .
Step4:Check
The measurement result
Please check the results
confirmation screen is
of the measured item.
displayed.
Speaker Config.Check
b
Distance Check
S ubwoofers or other
Channel Level Check
speakers may be set to
Crossover Freq.Check
a value that does not
[ENT]:Select
correspond to the actual
distance.
ENGLISH
MultEQ
Calculate
Retry
Cancel
⇩
MultEQ
MultEQ
Next
See overleaf
22