Zenith HCS5650 Installation And Operating Manual page 62

Installer Menu (Continued)
(Continued from previous page)
036 - FRONT Y/C EN. (HDMI 2 Enable)
Set to 1 to enable display panel HDMI 2 input.
Set to 0 to disable display panel HDMI 2 input.
038 - YPrPb EN. (Rear Component Video Enable)
Set to 1 to enable display panel rear Component Video 1 input.
Set to 0 to disable display panel rear Component Video 1 input.
039 - REAR AUX EN. (Rear Aux Enable)
Set to 1 to enable display panel rear AUX (Video 1) input.
Set to 0 to disable display panel rear AUX (Video 1) input.
046 - STRT AUX SRCE (Start Aux Source)
Sets the starting AUX source.
Start source if start channel =0
1 = Video 1 5 = Component 2
2 = Video 2 6 = Component 1
3 = HDMI 1 7 = RGB 2
4 = RGB 1 8 = HDMI 2
047 - AUX STATUS
Set to 1 for M.P.I. AUX source to be reported as a channel number
instead of channel 0. Set to 0 to disable AUX identification change.
Controls M.P.I. status channel response for AUX inputs.
053 - DIS. CH-TIME (Disable Channel-Time)
Set to 1 to disable the Channel-Time display, Channel-Time display
will not appear.
Set to 0 to enable the Channel-Time display.
069 - EN. CH-T COL. (Enable Text OSD Color)
Set to 1 to enable custom color for the Channel-Time display.
Set to 0 to disable custom color for the Channel-Time display.
070 - FOR. CH-TIME (Display Text Foreground Color)
Set according to Color Chart.
0 = Black 3 = Cyan
1 = Blue 4 = Red
2 = Green 5 = Violet
*Note: If foreground and background color are the same, menu
background is transparent.
071 - BCK. CH-TIME (Display Text Background Color)
Set according to Color Chart.
0 = Black 3 = Cyan
1 = Blue 4 = Red
2 = Green 5 = Violet
*Note: If foreground and background color are the same, menu
background is transparent.
073 - CH NOT AVBLE (Channel Not Available)
If set to 1 and item 028 CHANNEL OVERRIDE is set to 0, "NOT
AVAILABLE" message is displayed when directly accessing a channel
not in the channel scan list available in memory.
P A G E 6 2
6 = Yellow
7 = White
6 = Yellow
7 = White
075 - REVERT CH (Revert to Start Channel)
If set to 1 and loss of M.P.I. communication occurs, TV automatically
tunes to the specified Start Channel.
077 - QUICK SHUTOFF
Allows TV power off to be controlled by the pillow speaker channel
selection button. User would press and hold button down for time
required to have TV turn off.
Value Range 0 - 17, each number represents 1/2 second.
For example, if set to 4, TV would turn off if user held speaker chan-
nel button down for 2 seconds.
078 - UPN MSB (UPN Most Significant Byte)
User programmable number, most significant byte readable by M.P.I.
command. Note: Not linked to serial number.
079 - UPN MSB-1 (UPN Most Significant Byte-1)
User programmable number, most significant byte-1 readable by
M.P.I. command. Not linked to serial number.
080 - UPN MSB-2 (UPN Most Significant Byte-2)
User programmable number, most significant byte-2 readable by
M.P.I. command. Not linked to serial number.
081 - UPN LSB (UPN Least Significant Byte)
User programmable number, least significant byte readable by M.P.I.
command. Not linked to serial number.
082 - CHKSM ERROR (Checksum Error)
Enforces rigid M.P.I. checksum validation.
Set to 1 for validation.
Set to 0 to disable (does not check checksum on M.P.I. async port).
SPI is always checked.
083 - HANDSHK TIME (Handshake Time)
Adds an additional delay to the handshake time which is 64 msec,
thus relaxing M.P.I. timing requirements to be compatible with PC
based Windows controlled systems, range is 0 - 5.
(Timeout = 25.5MS + [25.5 MS* Handshake time]).
084 - PERMANENT BLK (Permanent Block)
Allows Lock (Parental Control) blocking schemes to be permanent by
disabling the blocking hours function.
Set to 1 to install Parental Control restrictions permanently.
Set to 0 for user-specified hours control of blocking schemes.
(Continued on next page)