Commercial Mode Setup - Zenith HCS5650 Installation And Operating Manual

Commercial Mode Setup

This page provides an overview of the TV configuration. See the pages listed below for more specific, detailed
instructions at each step; how to access and use the Installer menu etc.
*Note1: Disconnect all Aux inputs. Under certain conditions, Auto Program
(Channel search) is disabled if there is an Aux input active.
*Note2: Under certain conditions, changes to the input mode of the RGB
inputs will not take effect until the power is cycled (TV is turned Off and On).
Overview: Commercial Mode Setup Procedure
1.Set Installer Menu Items
(Enter Installer Menu, see page 58 for detailed instructions.)
a. Set Installer menu item 117 FACT DEFAULT, to 001 and press ENTER.
(This clears all installer menu items, custom settings, channel labels/icons
and reloads the factory default settings.)
b. Set Item 003 BAND/AFC.
- Broadcast: set to 000.
- CATV: set to 001.
c. Set item 028 CH OVERIDE to 001. This allows access to Auto Program,
Channel Labels and Channel List options in the Channel Menu.
d. Set other particular installer items that affect your TV programming
network. See pages 58 - 63.
e. After all required installer menu item settings have been adjusted, press
ENTER on the remote to remove Installer Menu.
2.Set Up TV Features
(See Picture, Sound, Setup menus etc. See TV Closable options list on page
64.) Installer Note: Some TV features will have to be set up after running.
Auto Program. An example is Digital Font options. This feature is not avail-
able until digital channels are found in the channel scan. Set up Digital
Font options after Auto Program finds a digital channel with digital cap-
tions. Do this before running 2-5-5 + Menu.
3.Run Auto Program
(Search for all available channels.) Go to the Channel menu and access
the Auto Program option, follow on-screen instructions.
a. Edit Channel Scan. In the Channel Menu, access the Channel List menu.
• Delete channels per your system requirements: do you want to delete any
free channels so the guest cannot access them?
• Add familiar Channel Icons like ABC, CBS, NBC etc. to the channel on-
screen display. Add identifiable labels for the end user to readily know
what common networks are available. In the Channel menu, select the
Channel Label option, follow instructions on the bottom of the screen.
4.Transfer TV Setup to Controller Box: 2-5-5 + Menu
After the TV channel scan has been edited and channel label icons added,
enter the Installer menu. Once in the Installer menu, press 2-5-5 and MENU
on the remote. This transfers the TV setup to the internal controller box.
*Note: Only do 2-5-5 + MENU once or TV setup may be corrupted. TV scans
available channels and exits menu when transfer to controller is complete.
5.Perform Adding Custom Channel Labels: 2-5-4 + Menu Mode
Enter Installer menu, press 2-5-4 and Menu. Add your own custom labels to
the channel on-screen displays. (See page 65.) To remove menu press MENU.
*Note: 2-5-4 + MENU can be performed more than once.
Verify TV Setup
At this point, verify that the channel lineup, channel icons and custom
labels are correct. Make sure the TV features are set per your requirements.
Set item 028 CH OVERIDE to 000 to lock the channel scan. After the preced-
ing has been completed, the Master TV setup is ready to be copied to the
LT2002 Clone Programmer, see next page.
P A G E 5 4
- HRC: set to 002
- IRC: set to 003
HCS5650XX PTC INSTALLER MENU
000 INSTALLER SEQ
UPN 000-000-000-000 FPGA 09F1
PTC V1.00.000 CPU V1.01.00
TV/STB Installer Menu
117 FACT DEFAULT
003 BAND/AFC
028 CH.OVERIDE
073 CH. NOT AVBLE
TV/STB Installer Menu Items
DIGITAL 19-3 ANALOG 2
MONO STEREO SAP
WXYZ
MONO
WXYZ
Custom Channel Label 'WXYZ' created in
2-5-4 + Menu Add Channel Label Mode
028 CH. OVERIDE
After TV setup has been verified,
set item 028 Ch Overide back to 000.
*Note: Default setting for Aux sources is to
be active in the installer menu. The Aux
sources will appear between the high-est
Analog and lowest Digital channel number
with Channel Up/Down. If the Aux sources
will not be used, it is advisable to set them
to 000 (Off) before doing 2-5-5 + Menu. After
doing 2-5-5 + Menu, the only way to turn the
Aux source off so they will not appear in the
channel scan, is to go to the Channel Bank
menus and turn each Aux source off by select-
ing 'Normal Delete' .
Refer to installer items: 34, 35, 38, 39, 87,
91, and 92.
000
00X
00X
001
001
000